Customer Support: 131 242

  • Shopping Cart
    There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS EN 61347-2-1 : 2001

Current

Current

The latest, up-to-date edition.

LAMP CONTROLGEAR - PART 2-1: PARTICULAR REQUIREMENTS FOR STARTING DEVICES (OTHER THAN GLOW STARTERS)

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2001

$396.52
Including GST where applicable

INTRODUCTION
1 Scope
2 Normative references
3 Definitions
4 General requirements
5 General notes on tests
6 Classification
7 Marking
8 Protection against accidental contact with live parts
9 Terminals
10 Provisions for earthing
11 Moisture resistance and insulation
12 Electric strength
13 Thermal endurance test for windings
14 Fault conditions
15 Heating of built-in and independent starting devices
16 Pulse voltage of ignitors
17 Mechanical strength
18 Construction
19 Creepage distances and clearances
20 Screws, current-carrying parts and connections
21 Resistance to heat, fire and tracking
22 Resistance to corrosion
Annex A (normative) - Test to establish whether a
        conductive part is a live part which may
        cause an electric shock
Annex B (normative) - Particular requirements for
        thermally protected lamp controlgear
Annex C (normative) - Particular requirements for
        electronic lamp controlgear with means
        of protection against overheating
Annex D (normative) - Requirements for carrying
        out the heating tests of thermally protected
        lamp controlgear
Annex E (normative) - Use of constant S other than
        4500 in t[w] tests
Annex F (normative) - Draught-proof enclosure
Annex G (informative) - Explanation of the derivation
        of the values of pulse voltages
Annex H (normative) - Tests
Annex I (normative) - Mechanical strength testing
Annex J (normative) - Precautions to be observed when
         measuring with sphere-gaps
Annex ZA (normative) - Normative references to
         international publications with the
         corresponding European publications
Bibliography

Defines particular safety requirements for starting devices (starters other than glow starters and ignitors) for fluorescent and other discharge lamps for use on a.c. supplies up to 1000 V at 50 Hz or 60 Hz which produce starting pulses not greater than 100 kV and which are used in combination with lamps and ballasts covered in IEC 60081, IEC 60188, IEC 60192, IEC 60662, IEC 60901, IEC 61167, IEC 61195, IEC 61199, IEC 61347-2-8 and IEC 61347-2-9.

Committee
CPL/34/3
DevelopmentNote
Together with BS EN 61347-1, it supersedes BS EN 60926. (04/2001) Supersedes 98/263269 DC. (10/2003) Supersedes 04/300382 DC. (06/2006) 2001 Edition Re-Issued in May 2014 & incorporates AMD 2 2014. Supersedes 11/30241984 DC. (05/2014)
DocumentType
Standard
Pages
28
PublisherName
British Standards Institution
Status
Current
Supersedes

EN 60188:2001 High-pressure mercury vapour lamps - Performance specifications
EN 60192:2001 Low pressure sodium vapour lamps - Performance specifications
EN 60068-2-75:2014 Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests
IEC 60662:2011 High-pressure sodium vapour lamps - Performance specifications
IEC 60192:2001 Low-pressure sodium vapour lamps - Performance specifications
IEC 60188:2001 High-pressure mercury vapour lamps - Performance specifications
EN 61199:2011/A2:2015 SINGLE-CAPPED FLUORESCENT LAMPS - SAFETY SPECIFICATIONS (IEC 61199:2011/A2:2014)
IEC 61347-1:2015 RLV Lamp controlgear - Part 1: General and safety requirements
EN 60255-8:1998 Electrical relays - Part 8: Thermal electrical relays
IEC 61199:2011+AMD1:2012+AMD2:2014 CSV Single-capped fluorescent lamps - Safety specifications
IEC 61167:2015 Metal halide lamps - Performance specification
IEC 60410:1973 Sampling plans and procedures for inspection by attributes
EN 61347-1:2015 Lamp controlgear - Part 1: General and safety requirements
IEC 60598-1:2014+AMD1:2017 CSV Luminaires - Part 1: General requirements and tests
IEC 60927:2007+AMD1:2013 CSV Auxiliaries for lamps - Starting devices (other than glow starters)- Performance requirements
IEC 60255-8:1990 Electrical relays - Part 8: Thermal electrical relays
IEC 60052:2002 Voltage measurement by means of standard air gaps
EN 60155:1995/A2:2007 GLOW-STARTERS FOR FLUORESCENT LAMPS
IEC 60068-2-75:2014 Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests
EN 60662:2012 High-pressure sodium vapour lamps - Performance specifications
IEC 60155:1993 Glow-starters for fluorescent lamps
ISO 3864:1984 Safety colours and safety signs
EN 61195:1999/A2:2015 DOUBLE-CAPPED FLUORESCENT LAMPS - SAFETY SPECIFICATIONS (IEC 61195:1999/A2:2014)
IEC 61195:1999+AMD1:2012+AMD2:2014 CSV Double-capped fluorescent lamps - Safety specifications

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.