BS EN 60384-1:2016

FOREWORD
INTRODUCTION
1 General
2 Technical data
3 Quality assessment procedures
4 Tests and measurement procedures
Annex A (informative) - Interpretation of sampling plans
        and procedures as described in IEC 60410 for use within
        quality assessment systems
Annex B (informative) - Rules for the preparation of detail
        specifications for capacitors and resistors for electronic
        equipment for use within quality assessment systems
Annex C (informative) - Layout of the first page of a PCP/CQC
        specification
Annex D (informative) - Requirements for capability approval
        test report
Annex E (informative) - Guide for pulse testing of capacitors
Annex F (informative) - Guidance for the extension of endurance
        tests on fixed capacitors
Annex G (normative) - Damp heat, steady state with voltage
        applied, for metallized film capacitors only
Annex H (normative) - Accelerated damp heat, steady state,
        for multilayer ceramic capacitors only
Annex Q (informative) - Quality assessment procedures
Bibliography
Annex ZA (normative) - Normative references to international
         publications with their corresponding European publications

Defines standard terms, inspection procedures and methods 000 of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose.

1.1 Scope This part of IEC60384 is a generic specification and is applicable to fixed capacitors for use in electronic equipment. It establishes standard terms, inspection procedures and methods of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose. 1.2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC60027 (all parts), Letter symbols to be used in electrical technology IEC60050 (all parts), International Electrotechnical Vocabulary 1 IEC60062, Marking codes for resistors and capacitors IEC60063, Preferred number series for resistors and capacitors IEC60068‑1:2013, Environmental testing— Part1: General and guidance IEC60068‑2‑1:2007, Environmental testing— Part2-1: Tests— Tests A: Cold IEC60068‑2‑2:2007, Environmental testing— Part2-2: Tests— Tests B: Dry heat IEC60068‑2‑6:2007, Environmental testing— Part2-6: Tests— Test Fc: Vibration (sinusoidal) IEC60068‑2‑13:1983, Environmental testing— Part2-13: Tests— Test M: Low air pressure IEC60068‑2‑14:2009, Environmental testing— Part2-14: Tests— Test N: Change of temperature IEC60068‑2‑17:1994, Environmental testing— Part2-17: Tests— Test Q: Sealing IEC60068‑2‑20:2008, Environmental testing— Part2-20: Tests— Test T: Test methods for solderability and resistance to soldering heat of devices with leads IEC60068‑2‑21:2006, Environmental testing— Part2-21: Tests— Test U: Robustness of terminations and integral mounting devices IEC60068‑2‑27:2008, Environmental testing— Part2-27: Tests— Test Ea and guidance: Shock IEC60068‑2‑30:2005, Environmental testing— Part2-30: Tests— Test Db: Damp heat, cyclic (12h+12h cycle) IEC60068‑2‑45:1980, Environmental testing— Part2-45: Tests— Test XA and guidance: Immersion in cleaning solvents IEC60068-2-45:1980/AMD1:1993 IEC60068‑2‑54:2006, Environmental testing— Part2-54: Tests— Test Ta: Solderability testing of electronic components by the wetting balance method IEC60068‑2‑58:2015, Environmental testing— Part2-58: Tests— Test Td: Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD) IEC60068‑2‑67:1995, Environmental testing— Part2-67: Tests— Test Cy: Damp heat, steady state, accelerated test primarily intended for components IEC60068‑2‑69:2007, Environmental testing— Part2-69: Tests— Test Te: Solderability testing of electronic components for surface mounting devices (SMD) by the wetting balance method IEC60068‑2‑78:2012, Environmental testing— Part2-78: Tests— Test Cab: Damp heat, steady state IEC60068‑2‑82:2007, Environmental testing— Part2-82: Tests— Test XW1: Whisker test methods for electronic and electric components IEC60294, Measurement of the dimensions of a cylindrical component with axial terminations IEC60617, Graphical symbols for diagrams IEC60695‑11‑5:2004, Fire hazard testing— Part11-5: Test flames— Needle-flame test method— Apparatus, confirmatory test arrangement and guidance IEC60717, Method for the determination of the space required by capacitors and resistors with unidirectional terminations IEC61193‑2, Quality assessment systems— Part2: Selection and use of sampling plans for inspection of electronic components and packages IEC61249‑2‑7:2002, Materials for printed boards and other interconnecting structures— Part2-7: Reinforced base materials clad and unclad— Epoxide woven E-glass laminated sheet of defined flammability (vertical burning test), copper-clad ISO3, Preferred numbers— Series of preferred numbers ISO80000‑1, Quantities and units— Part1: General