Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS EN 1803:2002

Current

Current

The latest, up-to-date edition.

Transportable gas cylinders. Periodic inspection and testing of welded carbon steel gas cylinders

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

25-03-2002

$443.41
Including GST where applicable

Foreword
Introduction
1 Scope
2 Normative references
3 Intervals between periodic inspection and test
4 List of procedures for periodic inspection and test
5 Identification of cylinder and preparation for
   inspection and test
6 External visual inspection
7 Internal visual inspection
8 Supplementary tests
9 Inspection of cylinder neck
10 Pressure test
11 Repair of cylinders
12 Inspection of valve
13 Final operations
14 Rejection and rendering cylinder unserviceable
Annex A (informative) Gas cylinders manufactured
        according to National Regulations
Annex B (normative) Inspection periods
Annex C (normative) Description, evaluation of defects
        and conditions for rejection of welded carbon
        steel gas cylinders at time of visual inspection
Annex D (normative) Procedure to be adopted when a
        cylinder valve is suspected to be obstructed
Annex E (normative) Proof pressure test of gas cylinders
Annex F (informative) Inspection and maintenance of
        valves and their connections: recommended
        procedures
Annex G (informative) List of commonly used gases
        corrosive to cylinder material
Bibliography

Gives the requirements for periodic inspection and testing of welded, carbon steel transportable gas cylinders intended for compressed and liquefied gases under pressure, of water capacity from 0,5 L up to 150 L.

Committee
PVE/3/7
DevelopmentNote
Supersedes BS 5430-2(1990) and 95/702035 DC (04/2002)
DocumentType
Standard
Pages
30
PublisherName
British Standards Institution
Status
Current
Supersedes

This European Standard specifies the requirements for periodic inspection and testing of welded, carbon steel transportable gas cylinders intended for compressed and liquefied gases under pressure, of water capacity from 0,5 l up to 150 l.

NOTE As far as practicable, this standard may also be applied to cylinders of less than 0,5 l water capacity.

This Standard specifies the requirements for periodic inspection and testing to verify the integrity of such gas cylinders to be reintroduced into service for a further period of time. It also defines a procedure to qualify existing gas cylinders for free movement between member states of the European Union (see annex A).

This standard does not apply to periodic inspection and testing of acetylene cylinders or composite (fully wrapped or hoop-wrapped) steel cylinders.

This standard is primarily for industrial gases other than LPG but may also be applied for LPG. However for dedicated LPG cylinders, see EN 1440, Transportable refillable welded steel cylinders for liquefied petroleum gas (LPG) – Periodic requalification prepared by CEN/TC 286 – Liquefied petroleum gas equipment and accessories.

Standards Relationship
NS EN 1803 : 1ED 2002 Identical
I.S. EN 1803:2002 Identical
EN 1803:2002 Identical
UNI EN 1803 : 2004 Identical
NEN EN 1803 : 2002 Identical
UNE-EN 1803:2003 Identical
SN EN 1803 : 2002 Identical
NF EN 1803 : 2002 Identical
NBN EN 1803 : 2002 Identical
DIN EN 1803:2002-09 Identical

07/30152563 DC : 0 BS 5306-3 - FIRE EXTINGUISHING INSTALLATIONS AND EQUIPMENT ON PREMISES - PART 3: CODE OF PRACTICE FOR THE COMMISSIONING AND MAINTENANCE OF PORTABLE FIRE EXTINGUISHERS
BS 5306-3:2003 Fire extinguishing installations and equipment on premises Code of practice for the inspection and maintenance of portable fire extinguishers
DEFSTAN 00-970(PT0)/9(2012) : 2012 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
DEFSTAN 00-970(PT0)/17(2016) : 2016 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
DEFSTAN 00-970(PT9)/5(2009) : 2009 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 9: UAV SYSTEMS
DEFSTAN 00-970(PT0)/7(2011) : 2011 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
DEFSTAN 00-970(PT0)/14(2014) : 2014 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
DEFSTAN 00-970(PT0)/13(2014) : 2014 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
DEFSTAN 00-970(PT0)/11(2013) : 2013 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
DEFSTAN 00-970(PT0)/12(2014) : 2014 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
DEFSTAN 00-970(PT0)/15(2015) : 2015 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
DEFSTAN 00-970(PT0)/8(2011) : 2011 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
DEFSTAN 00-970(PT0)/16(2015) : 2015 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
DEFSTAN 00-970(PT0)/10(2013) : 2013 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
BS 341-4:2004 Transportable gas container valves Pressure relief devices
BS 5306-3:2009 Fire extinguishing installations and equipment on premises Commissioning and maintenance of portable fire extinguishers. Code of practice

EN 629-2 : 1996 TRANSPORTABLE GAS CYLINDERS - 25E TAPER THREAD FOR CONNECTION OF VALVES TO GAS CYLINDERS - GAUGE INSPECTION
ISO 11114-1:2012 Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials
PREN 14189 : DRAFT 2001 TRANSPORTABLE GAS CYLINDERS - INSPECTION AND MAINTENANCE OF CYLINDER VALVES AT TIME OF PERIODIC INSPECTION OF GAS CYLINDERS
EN 1089-1 : 1996 TRANSPORTABLE GAS CYLINDERS - GAS CYLINDER IDENTIFICATION (EXCLUDING LPG) - STAMPMARKING
ISO 13341:2010 Gas cylinders — Fitting of valves to gas cylinders
EN 1795 : 1997 TRANSPORTABLE GAS CYLINDERS (EXCLUDING LPG) - PROCEDURES FOR CHANGE OF GAS SERVICE
PREN 13322-2 : DRAFT 1998 TRANSPORTABLE GAS CYLINDERS - REFILLABLE WELDED STAINLESS STEEL GAS CYLINDERS- DESIGN AND CONSTRUCTION - WELDED STAINLESS STEEL
PREN 13322-1 : DRAFT 1998 TRANSPORTABLE GAS CYLINDERS - REFILLABLE WELDED STEEL GAS CYLINDERS - DESIGN AND CONSTRUCTION - WELDED STEEL
ISO 11114-2:2013 Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 2: Non-metallic materials
EN ISO 11114-2:2013 Gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 2: Non-metallic materials (ISO 11114-2:2013)
EN 1089-3:2011 Transportable gas cylinders - Gas cylinder identification (excluding LPG) - Part 3: Colour coding
EN 849:1996/A2:2001 TRANSPORTABLE GAS CYLINDERS - CYLINDER VALVES - SPECIFICATION AND TYPE TESTING
EN 1089-2 : 2002 TRANSPORTABLE GAS CYLINDERS - GAS CYLINDER IDENTIFICATION (EXCLUDING LPG) - PART 2: PRECAUTIONARY LABELS
EN 837-3:1996 Pressure gauges - Part 3: Diaphragm and capsule pressure gauges - Dimensions, metrology, requirements and testing

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more