BS EN 15383 : 2012
Current
The latest, up-to-date edition.
PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS
Hardcopy , PDF
English
01-01-2012
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 General requirements
5 Geometrical characteristics
6 Mechanical characteristics
7 Leak-tightness of manholes and inspection chambers and
their joints
8 Minimum required marking
9 Ancillary products
10 Dangerous substances
11 Manufacturer's installation recommendations
12 Evaluation of conformity
Annex A (normative) - Determination of the longitudinal
compressive properties measured on prism shaped test
pieces
Annex B (normative) - Determination of the resistance of
installed steps to vertical or horizontal loading
Pertains to: a) manholes, when made from glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP); b) inspection chambers, when made from glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) which are intended to be used with inverts which are at a depth not exceeding 2 m.
| Committee |
PRI/88/2/P5
|
| DevelopmentNote |
Supersedes 05/30141329 DC & 10/30237537 DC. (01/2013) 2012 Edition Re-Issued in October 2013 & incorporates AMD 1 2013. (11/2013)
|
| DocumentType |
Standard
|
| Pages |
34
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| EN 15383:2012+A1:2013 | Identical |
| EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
| EN 14396:2004 | Fixed ladders for manholes |
| EN ISO 604:2003 | Plastics - Determination of compressive properties (ISO 604:2002) |
| CEN/TS 14632:2012 | Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the assessment of conformity |
| ISO 2602:1980 | Statistical interpretation of test results Estimation of the mean Confidence interval |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| EN 476:2011 | General requirements for components used in drains and sewers |
| ISO 8533:2003 | Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin Test methods to prove the design of cemented or wrapped joints |
| EN 124:1994 | Gully tops and manhole tops for vehicular and pedestrian areas - Design requirements, type testing, marking, quality control |
| ISO 604:2002 | Plastics — Determination of compressive properties |
| EN 13101:2002 | Steps for underground man entry chambers - Requirements, marking, testing and evaluation of conformity |
| EN 1119:2009 | Plastics piping systems - Joints for glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods for leaktightness and resistance to damage of non-thrust resistant flexible joints with elastomeric sealing elements |
| EN 14364:2013 | Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.