BS EN 14188-1:2004
Current
The latest, up-to-date edition.
Joint fillers and sealants Specifications for hot applied sealants
Hardcopy , PDF
English
29-09-2004
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification and specification
4.1 Joint sealant
4.2 Primer
5 Requirements
5.1 Shelf life
5.2 Compliance to requirements after safe heating temperature
5.3 Softening point
5.4 Density
5.5 Cone penetration
5.6 Penetration and recovery at +25 Degrees C (resilience)
5.7 Heat stability
5.8 Flow resistance
5.9 Resistance to fuel immersion (solubility)
5.10 Compatibility with asphalt pavements
5.11 Bonding strength
5.12 Cohesion
5.13 Dangerous substances
6 Evaluation of conformity
6.1 General
6.2 Type Testing
6.2.1 Initial Type Testing (ITT)
6.2.2 Further Type Testing
6.3 Factory Production Control (FPC)
6.3.1 General
6.3.2 Frequency of testing
6.3.3 Equipment
6.3.4 Raw materials and components
6.3.5 Design process
6.3.6 Non-conforming products
7 Marking, labelling and packaging
7.1 General
7.2 Hot applied joint sealant
7.3 Primer
7.4 Containers
Annex A (normative) Initial Type Testing and frequencies of
testing for Factory Production Control
Annex B (informative) Example of a product data sheet
B.1 General information
Annex ZA (informative) Clauses of this European Standard
addressing essential requirements or other provisions
of EU Directives
ZA.1 Scope and relevant characteristics
ZA.2 Procedure(s) for attestation of conformity
ZA.2.1 Systems of attestation of conformity
ZA.2.2 EC Certificate and declaration of conformity
ZA.3 CE marking and labelling
Bibliography
Describes the requirements for hot-applied normal and fuel resistant joint sealants to be used in roads, airfields and other trafficked areas.
| Committee |
B/510/3
|
| DevelopmentNote |
Supersedes BS 2499-1(1993) (09/2004) Supersedes 01/103314 DC (10/2004)
|
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
This document specifies requirements for hot-applied normal and fuel resistant joint sealants to be used in roads, airfields and other trafficked areas. The specification also applies to hot-applied normal joint sealants in bituminous surfacing and between bituminous surfacing and concrete pavements.
| Standards | Relationship |
| NS EN 14188-1 : 1ED 2004 | Identical |
| NF EN 14188-1 : 2005 | Identical |
| EN 14188-1:2004 | Identical |
| NBN EN 14188-1 : 2004 | Identical |
| DIN EN 14188-1:2004-12 | Identical |
| SN EN 14188-1 : 2005 | Identical |
| I.S. EN 14188-1:2004 | Identical |
| UNE-EN 14188-1:2005 | Identical |
| NEN EN 14188-1 : 2004 | Identical |
| UNI EN 14188-1 : 2004 | Identical |
| BS 5385-3:2014 | Wall and floor tiling Design and installation of internal and external ceramic and mosaic floor tiling in normal conditions. Code of practice |
| 14/30283603 DC : 0 | BS 5385-3 - WALL AND FLOOR TILING - PART 3: DESIGN AND INSTALLATION OF INTERNAL ANDEXTERNAL CERAMIC AND MOSAIC FLOOR TILING IN NORMAL CONDITIONS - CODE OF PRACTICE |
| 08/30043515 DC : DRAFT FEB 2008 | BS 5385-1 - WALL AND FLOOR TILING - PART 1: DESIGN AND INSTALLATION OF CERAMIC AND NATURAL STONE AND MOSAIC WALL TILING IN NORMAL INTERNAL CONDITIONS - CODE OF PRACTICE |
| EN 1427:2015 | Bitumen and bituminous binders - Determination of the softening point - Ring and Ball method |
| 89/106/EEC : 1988 | COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS |
| EN 13880-11:2003 | Hot applied joint sealants - Part 11: Test method for the preparation of asphalt test blocks used in the function test and for the determination of compatibility with asphalt pavements |
| EN 13880-8:2003 | Hot applied joint sealants - Part 8: Test method for the determination of the change in weight of fuel resistance joint sealants after fuel immersion |
| EN 13880-3:2003 | Hot applied joint sealants - Part 3: Test method for the determination of penetration and recovery (resilience) |
| EN 13880-4:2003 | Hot applied joint sealants - Part 4: Test method for the determination of heat resistance - Change in penetration value |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN 13880-7:2003 | Hot applied joint sealants - Part 7: Function testing of joint sealants |
| EN 13880-9:2003 | Hot applied joint sealants - Part 9: Test method for the determination of compatibility with asphalt pavements |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN 13880-5:2004 | Hot applied joint sealants - Part 5: Test method for the determination of flow resistance |
| EN 13880-2:2003 | Hot applied joint sealants - Part 2: Test method for the determination of cone penetration at 25°C |
| EN 13880-6:2004 | Hot applied joint sealants - Part 6: Method for the preperation of samples for testing |
| EN 13880-13:2003 | Hot applied joint sealants - Part 13: Test method for the determination of the discontinuous extension (adherence test) |
| EN 13880-1:2003 | Hot applied joint sealants - Part 1: Test method for the determination of density at 25 °C |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.