BS EN 1366-1:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Fire resistance tests for service installations Ventilation ducts
Hardcopy , PDF
08-10-2020
English
31-10-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Test equipment
5 Test conditions
6 Test specimen
7 Installation of test specimen
8 Conditioning
9 Application of instrumentation
10 Test procedure
11 Performance criteria
12 Test report
13 Field of direct application of test results
Annex A (informative) - General guidance
Bibliography
Defines a method for determining the fire resistance of vertical and horizontal ventilation ducts including those access panels, which are integral part of the tested ducts.
| Committee |
FSH/22/-/9
|
| DevelopmentNote |
Supersedes 94/306101 DC. (09/2005) Supersedes 08/30176919 DC. (10/2014)
|
| DocumentType |
Standard
|
| Pages |
54
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This European Standard specifies a method for determining the fire resistance of vertical and horizontal ventilation ducts including those access panels, which are integral part of the tested ducts. The test examines the behaviour of ducts exposed to fire from the outside (duct A) and fire inside the duct (duct B). This European Standard is used in conjunction with EN1363‑1 . AnnexA provides general guidance and gives background information. This European Standard is not applicable to: ducts whose fire resistance depends on the fire resistance performance of a ceiling or wall (where ducts are located in cavities enclosed by fire-resistant shafts or ceilings); ducts containing fire dampers at points where they pass through fire separations; one, two or three sided ducts; fixing of suspension devices (e.g. anchors) to floors or walls.
| Standards | Relationship |
| ONORM EN 1366-1 : 2014 | Identical |
| I.S. EN 1366-1:2014 | Identical |
| NEN EN 1366-1 : 2014 | Identical |
| UNI EN 1366-1 : 2014 | Identical |
| NS EN 1366-1 : 2014 | Identical |
| EN 1366-1:2014 | Identical |
| NF EN 1366-1 : 2014 | Identical |
| UNE-EN 1366-1:2016 | Identical |
| SN EN 1366-1 : 2014 | Identical |
| NBN EN 1366-1 : 2014 | Identical |
| DIN EN 1366-1:2014-12 | Identical |
| 07/30147204 DC : 0 | BS 476-10 - FIRE TESTS ON BUILDING MATERIALS AND STRUCTURES - PART 10: GUIDE TO THE PRINCIPLES, SELECTION, ROLE AND APPLICATION OF FIRE TESTING AND THEIR OUTPUTS |
| PD 7974-3:2011 | Application of fire safety engineering principles to the design of buildings Structural response and fire spread beyond the enclosure of origin |
| BS 476-10:2009 | Fire tests on building materials and structures Guide to the principles, selection, role and application of fire testing and their outputs |
| PD 7974-3:2003 | Application of fire safety engineering principles to the design of buildings Structural response and fire spread beyond the enclosure of origin (Sub-system 3) |
| ISO 5167-3:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 3: Nozzles and Venturi nozzles |
| EN 520:2004+A1:2009 | Gypsum plasterboards - Definitions, requirements and test methods |
| EN 1507:2006 | Ventilation for buildings - Sheet metal air ducts with rectangular section - Requirements for strength and leakage |
| EN ISO 5167-2:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 2: Orifice plates (ISO 5167-2:2003) |
| EN 15882-1:2011+A1:2017 | Extended application of results from fire resistance tests for service installations - Part 1: Ducts |
| EN 1364-1:1999 | Fire resistance tests for non-loadbearing elements - Part 1: Walls |
| ISO 13943:2017 | Fire safety — Vocabulary |
| EN 12237:2003 | Ventilation for buildings - Ductwork - Strength and leakage of circular sheet metal ducts |
| ISO 5167-2:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 2: Orifice plates |
| EN ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003) |
| EN ISO 5167-3:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3: Nozzles and Venturi nozzles (ISO 5167-3:2003) |
| ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements |
| EN 1366-8:2004 | Fire resistance tests for service installations - Part 8: Smoke extraction ducts |
| EN 60584-1:2013 | Thermocouples - Part 1: EMF specifications and tolerances |
| EN ISO 13943:2017 | Fire safety - Vocabulary (ISO 13943:2017) |
| EN 1363-1:2012 | Fire resistance tests - Part 1: General Requirements |
| EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) |
| EN 1363-2:1999 | Fire resistance tests - Part 2: Alternative and additional procedures |
| IEC 60584-1:2013 | Thermocouples - Part 1: EMF specifications and tolerances |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.