BS EN 13348:2016
Current
The latest, up-to-date edition.
Copper and copper alloys. Seamless, round copper tubes for medical gases or vacuum
Hardcopy , PDF
English
30-06-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Designations
5 Ordering information
6 Requirements
7 Sampling
8 Test methods
9 Inspection documentation
10 Packaging, marking and form of delivery
Annex A (normative) - Marking durability test
Annex B (normative) - Freedom from defects test
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of Directive 2014/68/EU aimed
to be covered
Bibliography
Defines the requirements, sampling, test methods and conditions of delivery for copper tubes.
| Committee |
NFE/34
|
| DevelopmentNote |
Supersedes 98/716462 DC. (09/2001) Supersedes 04/30122982 DC. (09/2007)
|
| DocumentType |
Standard
|
| Pages |
26
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
This European Standard specifies the requirements, sampling, test methods and conditions of delivery for copper tubes. It is applicable to seamless round copper tubes having an outside diameter from 6 mm up to and including 219 mm for pipeline systems under vacuum or for distributing the following medical gases intended to be used at operating pressures up to 2 000 kPa: - oxygen, nitrous oxide, nitrogen, helium, carbon dioxide, xenon; - medical air; - specific mixtures of these above mentioned gases; - air for driving surgical tools; - anaesthetic gases and vapours.
| Standards | Relationship |
| UNI EN 13348 : 2008 | Identical |
| I.S. EN 13348:2016 | Identical |
| DIN EN 13348:2015-11 (Draft) | Identical |
| SN EN 13348:2016 | Identical |
| UNE-EN 13348:2016 | Identical |
| NS EN 13348 : 2001 | Identical |
| NBN EN 13348 : 2016 | Identical |
| NF EN 13348 : 2016 | Identical |
| EN 13348:2016 | Identical |
| NEN EN 13348 : 2016 | Identical |
| DIN EN 13348:2001-11 | Identical |
| BS PD5500(2015) : 2015 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| ISO 6507-1:2005 | Metallic materials Vickers hardness test Part 1: Test method |
| EN 1971-2:2011 | Copper and copper alloys - Eddy current test for measuring defects on seamless round copper and copper alloy tubes - Part 2: Test with an internal probe on the inner surface |
| EN ISO 8493:2004 | Metallic materials - Tube - Drift-expanding test (ISO 8493:1998) |
| EN 1412:2016 | Copper and copper alloys - European numbering system |
| ISO 1190-1:1982 | Copper and copper alloys — Code of designation — Part 1: Designation of materials |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| ISO 8491:1998 | Metallic materials Tube (in full section) Bend test |
| EN 1057:2006+A1:2010 | Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications |
| ISO 1553:1976 | Unalloyed copper containing not less than 99,90 % of copper Determination of copper content Electrolytic method |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| ISO 8493:1998 | Metallic materials Tube Drift-expanding test |
| EN 723:2009 | Copper and copper alloys - Combustion method for determination of the carbon content on the inner surface of copper tubes or fittings |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| ISO 7396-2:2007 | Medical gas pipeline systems Part 2: Anaesthetic gas scavenging disposal systems |
| EN 1971-1:2011 | Copper and copper alloys - Eddy current test for measuring defects on seamless round copper and copper alloy tubes - Part 1: Test with an encircling test coil on the outer surface |
| EN 1173:2008 | Copper and copper alloys - Material condition designation |
| EN ISO 6708:1995 | Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995) |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN ISO 7396-1:2016 | Medical gas pipeline systems - Part 1: Pipeline systems for compressed medical gases and vacuum (ISO 7396-1:2016) |
| ISO 4741:1984 | Copper and copper alloys — Determination of phosphorus content — Molybdovanadate spectrometric method |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| 2014/68/EU : 2014 COR 1 2015 | DIRECTIVE 2014/68/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 15 MAY 2014 ON THE HARMONISATION OF THE LAWS OF THE MEMBER STATES RELATING TO THE MAKING AVAILABLE ON THE MARKET OF PRESSURE EQUIPMENT TEXT WITH EEA RELEVANCE |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN ISO 8491:2004 | Metallic materials - Tube (in full section) - Bend test (ISO 8491:1998) |
| EN ISO 7396-2:2007 | Medical gas pipeline systems - Part 2: Anaesthetic gas scavenging disposal systems (ISO 7396-2:2007) |
| ISO 857-2:2005 | Welding and allied processes Vocabulary Part 2: Soldering and brazing processes and related terms |
| ISO 7396-1:2016 | Medical gas pipeline systems — Part 1: Pipeline systems for compressed medical gases and vacuum |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.