BS EN 12007-2:2012
Current
The latest, up-to-date edition.
Gas infrastructure. Pipelines for maximum operating pressure up to and including 16 bar Specific functional requirements for polyethylene (MOP up to and including 10 bar)
Hardcopy , PDF
English
31-08-2012
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
4 Design
5 Construction
6 Quality control
7 Pressure testing
Annex A (informative) - Storage, handling
and transportation
Annex B (informative) - Fusion joint integrity
Annex C (informative) - Technical changes between
this European Standard and EN 12007-2:2000
Bibliography
Specifies the specific functional requirements for polyethylene (PE) pipelines in addition to the general functional requirements of EN 12007-1 for: a) a maximum operating pressure (MOP) up to and including 10 bar; b) an operating temperature between -20 degrees C and +40 degrees C.
| Committee |
GSE/33
|
| DevelopmentNote |
Supersedes 95/709431 DC (08/2004) Supersedes 10/30208795 DC. (08/2012)
|
| DocumentType |
Standard
|
| Pages |
32
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
This European Standard describes the specific functional requirements for polyethylene (PE) pipelines in addition to the general functional requirements of EN 12007-1 for: a maximum operating pressure (MOP) up to and including 10 bar; an operating temperature between -20 °C and +40 °C. This European Standard covers three types of pipe: PE pipes including any identification stripes; PE pipes with co-extruded layers on either or both the outside and/or inside of the pipe; PE pipes with a peelable, contiguous thermoplastics additional layer on the outside of the pipe. This European Standard specifies common basic principles for gas infrastructure. Users of this European Standard should be aware that more detailed national standards and/or code of practice may exist in the CEN member countries. This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles. In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this European Standard, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737 (all parts). CEN/TR 13737 (all parts) give: clarification of all legislations/regulations applicable in a member state; if appropriate, more restrictive national requirements; a national contact point for the latest information.
| Standards | Relationship |
| DIN EN 12007-2:2012-10 | Identical |
| UNE-EN 12007-2:2013 | Identical |
| SN EN 12007-2:2012 | Identical |
| NF EN 12007-2 : 2012 | Identical |
| NBN EN 12007-2 : 2012 | Identical |
| UNI EN 12007-2 : 2012 | Identical |
| I.S. EN 12007-2:2012 | Identical |
| NS EN 12007-2 : 2012 | Identical |
| NEN EN 12007-2 : 2012 | Identical |
| EN 12007-2:2012 | Identical |
| EN 12327:2012 | Gas infrastructure - Pressure testing, commissioning and decommissioning procedures - Functional requirements |
| EN 1555-1:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General |
| EN 1555-3:2010+A1:2012 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings |
| EN 12007-3:2015 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 3: Specific functional requirements for steel |
| EN 12007-1:2012 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 1: General functional requirements |
| ISO 10838-2:2000 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm |
| ISO 21307:2011 | Plastics pipes and fittings Butt fusion jointing procedures for polyethylene (PE) pipes and fittings used in the construction of gas and water distribution systems |
| ISO 10838-1:2000 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm |
| ISO 12176-1:2017 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| ISO 12176-2:2008 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion |
| ISO 11414:2009 | Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion |
| EN 1555-4:2011 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 4: Valves |
| EN 1555-5:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 1555-2:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes |
| ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
| EN 12007-4:2012 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 4: Specific functional requirements for renovation |
| ISO 11413:2008 | Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.