BS EN 10155:1993
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Structural steels with improved atmospheric corrosion resistance. Technical delivery conditions
Hardcopy , PDF
17-11-2004
English
15-09-1993
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Cooperating organizations
National foreword
Foreword
1 Scope
2 Normative references
2.1 General standards
2.2 Standards on dimensions and tolerances
2.3 Standards on testing
3 Definitions
4 Information to be supplied by the purchaser
4.1 General
4.2 Options
5 Dimensions, mass and tolerances
5.1 Dimensions and tolerances
5.2 Mass of steel
6 Classification of grades and qualities;
designation
6.1 Classification of grades and qualities
6.2 Designation
7 Technical requirements
7.1 Steel manufacturing process
7.2 Delivery conditions
7.3 Chemical composition
7.4 Mechanical properties
7.5 Technological properties
7.6 Surface finish
8 Inspection and testing
8.1 General
8.2 Specific inspection and testing
8.3 Sampling
8.4 Test units
8.5 Verification of chemical composition
8.6 Mechanical tests
8.7 Test methods
8.8 Retests and resubmission for testing
8.9 Internal defects
8.10 Inspection documents
9 Marking for flat and long products
10 Complaints after delivery
11 Options
11.1 All products
11.2 Flat products
11.3 Long products
Annex A (normative) Location of samples and test pieces
(see EURONORM 18)
Annex B (informative) Additional information for the
use of steel with improved atmospheric
corrosion resistance
Annex C (informative) Notes on fabrication
Annex D (informative) List of national standards which
correspond with EURONORMS referenced
Annex E (informative) List of corresponding former
designations
National annex NA (informative) Committees responsible
National annex NB (informative) Cross-references
Specifies requirements for long products and flat products of hot-rolled steels with improved atmospheric corrosion resistance. Includes the following sections: technical requirements; inspection and testing; marking for flat and long products. Coverage also includes surface finish, mechanical tests, internal defects, and definitions. Also gives detailed annexes.
| Committee |
ISE/103
|
| DevelopmentNote |
Together with BS 7613(1994), BS 7668(1994), BS EN 10029, BS EN 10113-1, BS EN 10113-2, BS EN 10113-3, and BS EN 10210-1 supersedes BS 4360(1990). Supersedes 91/35823 DC. (07/2005)
|
| DocumentType |
Standard
|
| Pages |
28
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 4952:2006 | Similar to |
| UNE-EN 10155:1994 | Identical |
| I.S. EN 10155:1994 | Identical |
| NEN EN 10155 : 1993 | Identical |
| SN EN 10155 : 1994 | Identical |
| NS EN 10155 : 1ED 1993 | Identical |
| NF EN 10155 : 1993 | Identical |
| UNI EN 10155 : 1995 | Identical |
| NBN EN 10155 : 1993 | Identical |
| EN 10155 : 1993 | Identical |
| DIN EN 10155:1993-08 | Identical |
| EN 10113-2 : 1993 | HOT-ROLLED PRODUCTS IN WELDABLE FINE GRAIN STRUCTURAL STEELS - DELIVERY CONDITIONS FOR NORMALIZED/NORMALIZED ROLLED STEELS |
| EN 10113-3 : 1993 | HOT ROLLED PRODUCTS IN WELDABLE FINE GRAIN STRUCTURAL STEELS - DELIVERY CONDITIONS FOR THERMOMECHANICAL ROLLED STEELS |
| 02/703583 DC : DRAFT FEB 2002 | BS 7668 - WELDABLE STRUCTURAL STEELS - HOT FINISHED STRUCTURAL HOLLOW SECTIONS IN WEATHER RESISTANT STEELS |
| BS 6180:1999 | Barriers in and about buildings. Code of practice |
| BS 6349-1:2000 | Maritime structures Code of practice for general criteria |
| BS 5950-2:2001 | STRUCTURAL USE OF STEELWORK IN BUILDING - PART 2: SPECIFICATION FOR MATERIALS, FABRICATION AND ERECTION - ROLLED AND WELDED SECTIONS |
| BS 5950-1:2000 | Structural use of steelwork in building Code of practice for design. Rolled and welded sections |
| BS 4074:2000 | Specification for steel trench struts |
| BS EN 10113-2:1993 | Hot-rolled products in weldable fine grain structural steels Delivery conditions for normalized/normalized rolled steels |
| DD ENV 1090-1:1998 | Execution of steel structures General rules and rules for buildings (together with United Kingdom national application document) |
| BS EN 10113-3:1993 | Hot-rolled products in weldable fine grain structural steels Delivery conditions for thermomechanical rolled steels |
| BS 5400-3:2000 | Steel, concrete and composite bridges Code of practice for design of steel bridges |
| BS 5975:1996 | Code of practice for falsework |
| BS 5400-6:1999 | STEEL, CONCRETE AND COMPOSITE BRIDGES - PART 6: SPECIFICATION FOR MATERIALS AND WORKMANSHIP, STEEL |
| EURONORM 54 : 1980 | HOT-ROLLED SMALL U-BEAMS |
| EN 10002-1 : 2001 | METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE |
| EURONORM 57 : 1978 | HOT-ROLLED ROUND-EDGE UNEQUAL ANGLE STEEL |
| EURONORM 55 : 1980 | HOT-ROLLED ROUND-EDGE EQUAL ANGLE T-BEAMS |
| EN 10051:2010 | Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape |
| EN 10079:2007 | Definition of steel products |
| EN 10027-2:2015 | Designation systems for steels - Part 2: Numerical system |
| EN 10029:2010 | Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape |
| EURONORM 18 : 1979 | TAKING AND PREPARATION OF SAMPLES AND SAMPLE SECTIONS OF STEEL AND STEEL PRODUCTS |
| EN 10164:2004 | Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions |
| EURONORM 24 : 1962 | NORMAL I-BEAMS, U-BEAMS; PERMISSIBLE DEVIATIONS |
| EN 10025:1990/A1:1993 | HOT ROLLED PRODUCTS OF NON-ALLOY STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS |
| EURONORM 48 : 1984 | HOT-ROLLED STRIP STEEL; PERMISSIBLE DEVIATIONS IN DIMENSIONS AND FORM |
| EURONORM 53 : 1962 | HOT-ROLLED BROAD FLANGED I-BEAMS (WIDE-FLANGED I-BEAMS) WITH PARALLEL FLANGE FACINGS |
| EURONORM 103 : 1971 | MICROSCOPIC DETERMINATION OF THE FERRITE OR AUSTENITIC GRAIN SIZE OF STEELS |
| EURONORM 60 : 1977 | HOT-ROLLED ROUND STEEL FOR GENERAL USE |
| EURONORM 56 : 1977 | HOT-ROLLED ROUND-EDGE EQUAL ANGLE STEEL |
| EN 10045-1 : 1990 | METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD |
| EURONORM 19 : 1957 | IPE BEAMS - I-BEAMS WITH PARALLEL FLANGE FACINGS |
| EN 10163-2:2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats |
| EN 10021:2006 | General technical delivery conditions for steel products |
| EURONORM 58 : 1978 | HOT-ROLLED FLAT STEEL FOR GENERAL USE |
| ISO 2566-1:1984 | Steel Conversion of elongation values Part 1: Carbon and low alloy steels |
| EN 10163-3:2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 3: Sections |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN 10027-1:2016 | Designation systems for steels - Part 1: Steel names |
| EN 10020:2000 | Definition and classification of grades of steel |
| EURONORM 168 : 1986 | IRON AND STEEL PRODUCTS - INSPECTION DOCUMENTS, CONTENTS |
| EURONORM 59 : 1978 | HOT-ROLLED SQUARE STEEL FOR GENERAL USE |
| EURONORM 91 : 1981 | HOT-ROLLED WIDE FLATS - PERMISSIBLE DEVIATIONS FOR DIMENSION, FORM AND WEIGHT |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.