Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS 6564-3:1990

Current

Current

The latest, up-to-date edition.

Polytetrafluoroethylene (PTFE) materials and products Specification for E glass fibre filled polytetrafluoroethylene

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

28-02-1990

$268.61
Including GST where applicable

Foreword
Committees responsible
Specification
0 Introduction
1 Scope
2 Definition
3 Designation
4 Composition and appearance
5 Performance and physical properties
6 Dimensional tolerances
7 Sampling
8 Marking
Tables
1 Forms, grades, subgrades and types covered by
   BS 6465 : Part 3
2 Performance and physical properties
3 Tolerance on nominal outside diameter
4 Tolerance on thickness of sheet
5 Tolerance on nominal width and nominal thickness of
   veneered tape
Appendices
A Information to be agreed between the purchaser and
   the supplier
B Method for determining compression modulus

Specifies three levels of glass filling and two levels of performance.

Committee
PRI/82
DevelopmentNote
Supersedes 88/36032 DC. (09/2005) Reviewed and confirmed by BSI, December 2011. (11/2011)
DocumentType
Standard
Pages
14
PublisherName
British Standards Institution
Status
Current

This Part of BS 6564 specifies requirements for fabricated E glass fibre filled polytetrafluoroethylene (PTFE) products which may occur in several forms, available in the grades, subgrades and types as indicated in Table 1.

NOTE 1 E glass is defined in BS 3447 as “a glass containing not more than 1 % of alkali (calculated as Na2O) and used for the manufacture of glass fibres??.

NOTE 2 The titles of the publications referred to in this standard are listed on the inside back cover.

BS 6564-1.1(1989) : 1989 POLYTETRAFLUOROETHYLENE (PTFE) MATERIALS AND PRODUCTS - POLYTETRAFLUOROETHYLENE POWDERS FOR MOULDING AND EXTRUSION - SPECIFICATION
04/30091878 DC : DRAFT FEB 2004 BS EN ISO 13000-2 - PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
I.S. EN ISO 13000-2:2006 PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
BS 6564-1.2(1989) : 1989 POLYTETRAFLUOROETHYLENE (PTFE) MATERIALS AND PRODUCTS - POLYTETRAFLUOROETHYLENE POWDERS FOR MOULDING AND EXTRUSION - METHOD OF SPECIFYING
BS EN ISO 13000-2:2005 Plastics. Polytetrafluoroethylene (PTFE) semi-finished products Preparation of test specimens and determination of properties
ISO 13000-2:2005 Plastics Polytetrafluoroethylene (PTFE) semi-finished products Part 2: Preparation of test specimens and determination of properties
EN ISO 13000-2:2005 Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 2: Preparation of test specimens and determination of properties (ISO 13000-2:2005)
DIN EN ISO 13000-2:2006-02 Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 2: Preparation of test specimens and determination of properties (ISO 13000-2:2005)

BS 6564-2:1985 Polytetrafluoroethylene (PTFE) materials and products. Specification for fabricated unfilled polytetrafluoroethylene products
BS 2782-3 Method 345A:1979 Methods of testing plastics. Mechanical properties Determination of compressive properties by deformation at constant rate
BS 6564-1.1(1989) : 1989 POLYTETRAFLUOROETHYLENE (PTFE) MATERIALS AND PRODUCTS - POLYTETRAFLUOROETHYLENE POWDERS FOR MOULDING AND EXTRUSION - SPECIFICATION
BS 2782-3 Method 327A:1982 Methods of testing plastics. Mechanical properties Determination of tensile strength and elongation at break of polytetrafluoroethylene (PTFE) products
BS 3447:1962 Glossary of terms used in the glass industry
BS 2782-6 Methods 620A to 620D:1980 Methods of testing plastics. Dimensional properties Determination of density of solid plastics excluding cellular plastics (immersion method). Determination of density of solid plastics excluding cellular plastics (pyknometer method). Determination of density of solid plastics excluding cellular plastics (sink-float method). Determination of density of solid plastics excluding cellular plastics (density gradient column method)

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more