BS 5930:2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Code of practice for ground investigations
Hardcopy , PDF
11-06-2020
English
31-07-2015
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
Section 1: Preliminary considerations
4 Primary objectives
5 Safety on investigation sites
6 Personnel for ground investigations
7 Investigation strategy
8 Planning and control of investigations
9 Quality management
Section 2: Desk study and field reconnaissance
10 General
11 Desk study
12 Field reconnaissance
13 Earlier uses and state of site
14 Aerial photographs and satellite imagery
Section 3: Planning ground investigations
15 Types of ground investigation
16 Geological mapping
17 Scope of the ground investigation
18 Frequency of sampling and testing
19 General considerations in the selection of methods
of ground investigation
20 The effect of ground conditions on the selection
of methods of intrusive investigation
21 Ground chemically aggressive or prone to volume change
22 Ground investigations over water
Section 4: Exploratory holes
23 Surveying of investigation points
24 Excavations and boreholes
25 Sampling the ground
26 Groundwater monitoring and sampling
Section 5: Geophysical field investigations
27 General
28 The use of geophysical surveys as part of a ground
investigation
29 Geophysical techniques
30 Application of geophysical techniques
31 Specification and planning of a geophysical survey
Section 6: Description of soils and rocks
32 The description process
33 Description of soils
34 Field procedures for description of principal inorganic soil
type
35 Classification of soils
36 Description and classification of rocks
Section 7: Field tests
Section 8: Field instrumentation
50 General
51 Planning a field monitoring programme
52 Groundwater measurements
53 Inclinometers
54 Extensometers
Section 9: Laboratory tests on samples
55 General
56 Roles and responsibilities
57 Health and safety in laboratories
58 Sample storage and inspection facilities
59 Selection of testing programme
60 Visual examination and description of laboratory samples
61 Laboratory tests
Section 10: Reports and interpretation
62 General
63 Reports
Section 11: Review during and after construction
64 General
65 Purpose of review
66 Information required
67 Monitoring
68 Reporting
Annexes
Annex A (informative) - National safety legislation and
guidance
Annex B (informative) - General information for a desk study
Annex C (informative) - Sources of information
Annex D (informative) - Detailed information for design and
construction
Annex E (informative) - Notes on field reconnaissance
Annex F (informative) - Ground investigations and
development in ground potentially containing voids
Annex G (informative) - Integrated investigations
Annex H (informative) - Photographic records
Bibliography
Defines recommendations for the investigation of sites for the purposes of assessing their suitability for the construction of civil engineering and building works and of acquiring knowledge of the characteristics of a site that could affect the design and construction of such work and the security of neighbouring land and property.
Committee |
B/526/7
|
DevelopmentNote |
Supersedes BS 5930(1999) & 14/30268442 DC. (07/2015)
|
DocumentType |
Standard
|
Pages |
328
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
BS 8006-2(2011) : 2011 | CODE OF PRACTICE FOR STRENGTHENED/REINFORCED SOILS - PART 2: SOIL NAIL DESIGN |
BS 10175(2011) : 2011 | INVESTIGATION OF POTENTIALLY CONTAMINATED SITES - CODE OF PRACTICE |
BS 1377-1:2016 | Methods of test for soils for civil engineering purposes General requirements and sample preparation |
BS 5607:2017 | Code of practice for the safe use of explosives in the construction industry |
BS 8081:2015 | CODE OF PRACTICE FOR GROUTED ANCHORS |
BS 6349-5:2016 | Maritime works Code of practice for dredging and land reclamation |
BS EN ISO 5667-1:2006 | Water quality. Sampling Guidance on the design of sampling programmes and sampling techniques |
BS EN ISO 22476-3 : 2005 | GEOTECHNICAL INVESTIGATION AND TESTING - FIELD TESTING - PART 3: STANDARD PENETRATION TEST |
BS 5493:1977 | Code of practice for protective coating of iron and steel structures against corrosion |
BS EN 933-9 : 2009 | TESTS FOR GEOMETRICAL PROPERTIES OF AGGREGATES - PART 9: ASSESSMENT OF FINES - METHYLENE BLUE TEST |
BS EN ISO 22282-3:2012 | Geotechnical investigation and testing. Geohydraulic testing Water pressure tests in rock |
BS ISO 15176:2002 | Soil quality. Characterization of excavated soil and other soil materials intended for re-use |
BS EN 1744-5:2006 | Tests for chemical properties of aggregates Determination of acid soluble chloride salts |
DIN 18196:2011-05 | Earthworks and foundations - Soil classification for civil engineering purposes |
BS EN 1097-1:2011 | Tests for mechanical and physical properties of aggregates Determination of the resistance to wear (micro-Deval) |
BS EN 1367-4:2008 | Tests for thermal and weathering properties of aggregates Determination of drying shrinkage |
ASTM E 228 : 2017 : REDLINE | Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer |
ASTM D 5731 : 2016 : REDLINE | Standard Test Method for Determination of the Point Load Strength Index of Rock and Application to Rock Strength Classifications |
BS ISO 18400-201:2017 | Soil quality. Sampling Physical pretreatment in the field |
BS EN 1097-9:2014 | Tests for mechanical and physical properties of aggregates Determination of the resistance to wear by abrasion from studded tyres. Nordic test |
BS EN 1097-7:2008 | Tests for mechanical and physical properties of aggregates Determination of the particle density of filler. Pyknometer method |
BS EN ISO 17892-1:2014 | Geotechnical investigation and testing. Laboratory testing of soil Determination of water content |
BS EN 933-1:2012 | Tests for geometrical properties of aggregates Determination of particle size distribution. Sieving method |
BS EN 933-11:2009 | Tests for geometrical properties of aggregates Classification test for the constituents of coarse recycled aggregate |
BS EN 1367-1:2007 | Tests for thermal and weathering properties of aggregates Determination of resistance to freezing and thawing |
ASTM D 5335 : 2014 : REDLINE | Standard Test Method for Linear Coefficient of Thermal Expansion of Rock Using Bonded Electric Resistance Strain Gauges (Withdrawn 2023) |
ASTM D 5334 : 2014 : REDLINE | Standard Test Method for Determination of Thermal Conductivity of Soil and Soft Rock by Thermal Needle Probe Procedure |
BS EN ISO 22475-1:2006 | Geotechnical investigation and testing. Sampling methods and groundwater measurements Technical principles for execution |
BS EN ISO 22476-1:2012 | Geotechnical investigation and testing. Field testing Electrical cone and piezocone penetration test |
BS ISO 18512:2007 | Soil quality. Guidance on long and short term storage of soil samples |
BS 1377-7:1990 | Methods of test for soils for civil engineering purposes Shear strength tests (total stress) |
BS EN ISO 22476-12:2009 | Geotechnical investigation and testing. Field testing Mechanical cone penetration test (CPTM) |
BS EN ISO 22282-4:2012 | Geotechnical investigation and testing. Geohydraulic testing Pumping tests |
BS ISO 10381-3:2001 | Soil quality. Sampling Guidance on safety |
BS ISO 5667-22:2010 | Water quality. Sampling Guidance on the design and installation of groundwater monitoring points |
BS 1377-6:1990 | Methods of test for soils for civil engineering purposes Consolidation and permeability tests in hydraulic cells and with pore pressure measurement |
BS ISO 18400-102:2017 | Soil quality. Sampling Selection and application of sampling techniques |
BS PAS 128(2014) : 2014 | SPECIFICATION FOR UNDERGROUND UTILITY DETECTION, VERIFICATION AND LOCATION |
BS EN ISO 22476-7:2012 | Geotechnical investigation and testing. Field testing Borehole jack test |
BS EN 933-5:1998 | Tests for geometrical properties of aggregates Determination of percentage of crushed and broken surfaces in coarse aggregate particles |
BS 812-124:2009 | Testing aggregates Method for determination of frost heave |
BS EN ISO 14688-1 : 2002 | GEOTECHNICAL INVESTIGATION AND TESTING - IDENTIFICATION AND CLASSIFICATION OF SOIL - PART 1: IDENTIFICATION AND DESCRIPTION |
BS EN ISO 22282-5:2012 | Geotechnical investigation and testing. Geohydraulic testing Infiltrometer tests |
BS EN 1367-3:2001 | Tests for thermal and weathering properties of aggregates Boiling test for Sonnenbrand basalt |
BS EN 1997-2:2007 | Eurocode 7. Geotechnical design Ground investigation and testing |
BS EN 1744-6:2006 | Tests for chemical properties of aggregates Determination of the influence of recycled aggregate extract on the initial setting time of cement |
BS 8574:2014 | Code of practice for the management of geotechnical data for ground engineering projects |
BS EN ISO 11074:2015 | Soil quality. Vocabulary |
BS EN 1997-2 NA : 2007 | UK NATIONAL ANNEX TO EUROCODE 7: GEOTECHNICAL DESIGN - PART 2: GROUND INVESTIGATION AND TESTING |
BS EN 1097-10:2014 | Tests for mechanical and physical properties of aggregates Determination of water suction height |
BS EN ISO 22476-4:2012 | Geotechnical investigation and testing. Field testing Ménard pressuremeter test |
BS EN 1097-3:1998 | Tests for mechanical and physical properties of aggregates Determination of loose bulk density and voids |
ASTM D 6528 : 2017 | Standard Test Method for Consolidated Undrained Direct Simple Shear Testing of Fine Grain Soils |
BS EN 933-4:2008 | Tests for geometrical properties of aggregates Determination of particle shape. Shape index |
ASTM D 7664 : 2010 | Standard Test Methods for Measurement of Hydraulic Conductivity of Unsaturated Soils |
BS EN 1367-6:2008 | Tests for thermal and weathering properties of aggregates Determination of resistance to freezing and thawing in the presence of salt (NaCl) |
BS EN 12620:2013 | Aggregates for concrete |
BS EN 1367-5:2011 | Tests for thermal and weathering properties of aggregates Determination of resistance to thermal shock |
BS 1377-9:1990 | Methods for test for soils for civil engineering purposes In-situ tests |
ISO/TS 22476-11:2005 | Geotechnical investigation and testing Field testing Part 11: Flat dilatometer test |
BS ISO 14686:2003 | Hydrometric determinations. Pumping tests for water wells. Considerations and guidelines for design, performance and use |
ASTM D 4611 : 2016 : REDLINE | Standard Test Method for Specific Heat of Rock and Soil |
BS EN ISO 17892-2:2014 | Geotechnical investigation and testing. Laboratory testing of soil Determination of bulk density |
BS 1377-5:1990 | Methods of test for soils for civil engineering purposes Compressibility, permeability and durability tests |
BS EN 933-6:2014 | Tests for geometrical properties of aggregates Assessment of surface characteristics. Flow coefficient of aggregates |
BS EN ISO 19901-8:2015 | Petroleum and natural gas industries. Specific requirements for offshore structures Marine soil investigations |
BS CP2012-1(1974) : 1974 | CODE OF PRACTICE FOR FOUNDATIONS FOR MACHINERY - FOUNDATIONS FOR RECIPROCATING MACHINES |
BS EN 933-7:1998 | Tests for geometrical properties of aggregates Determination of shell content. Percentage of shells in coarse aggregates |
BS EN 1097-5:2008 | Tests for mechanical and physical properties of aggregates Determination of the water content by drying in a ventilated oven |
BS ISO 5667-11:2009 | Water quality. Sampling Guidance on sampling of groundwaters |
BS EN 932-1:1997 | Tests for general properties of aggregates Methods for sampling |
BS 1377-3:1990 | Methods of test for soils for civil engineering purposes Chemical and electro-chemical tests |
BS EN 1097-2:2010 | Tests for mechanical and physical properties of aggregates Methods for the determination of resistance to fragmentation |
BS EN 1744-1 : 2009 | TESTS FOR CHEMICAL PROPERTIES OF AGGREGATES - PART 1: CHEMICAL ANALYSIS |
BS EN 932-5:2012 | Tests for general properties of aggregates Common equipment and calibration |
BS EN ISO 22282-1:2012 | Geotechnical investigation and testing. Geohydraulic testing General rules |
BS 8576:2013 | Guidance on investigations for ground gas. Permanent gases and Volatile Organic Compounds (VOCs) |
BS EN ISO 22476-15:2016 | Geotechnical investigation and testing. Field testing Measuring while drilling |
BS 8008(1996) : 1996 | GUIDE TO SAFETY PRECAUTIONS AND PROCEDURES FOR THE CONSTRUCTION AND DESCENT OF MACHINE-BORED SHAFTS FOR PILING AND OTHER PURPOSES |
BS EN ISO 22476-2 : 2005 | GEOTECHNICAL INVESTIGATION AND TESTING - FIELD TESTING - PART 2: DYNAMIC PROBING |
BS 812-1:1975 | Testing aggregates Methods for determination of particle size and shape |
ASTM D 5607 : 2016 : REDLINE | Standard Test Method for Performing Laboratory Direct Shear Strength Tests of Rock Specimens Under Constant Normal Force |
BS EN ISO 22282-2:2012 | Geotechnical investigation and testing. Geohydraulic testing Water permeability tests in a borehole using open systems |
BS EN 1997-1 : 2004 | EUROCODE 7: GEOTECHNICAL DESIGN - PART 1: GENERAL RULES |
BS 22475-3:2011 | Geotechnical investigation and testing. Sampling methods and groundwater measurements Conformity assessment of enterprises and personnel by third party |
BS EN 1097-8:2009 | Tests for mechanical and physical properties of aggregates Determination of the polished stone value |
BS EN 1367-2:2009 | Tests for thermal and weathering properties of aggregates Magnesium sulfate test |
BS EN ISO 14689-1:2003 | Geotechnical investigation and testing. Identification and classification of rock. Identification and description |
BS 1377-4:1990 | Methods of test for soils for civil engineering purposes Compaction-related tests |
BS EN 1744-4:2005 | Tests for chemical properties of aggregates Determination of water susceptibility of fillers for bituminous mixtures |
BS EN ISO 22282-6:2012 | Geotechnical investigation and testing. Geohydraulic testing Water permeability tests in a borehole using closed systems |
BS EN ISO 14688-2 : 2004 | GEOTECHNICAL INVESTIGATION AND TESTING - IDENTIFICATION AND CLASSIFICATION OF SOIL - PRINCIPLES FOR A CLASSIFICATION |
BS EN 933-10:2009 | Tests for geometrical properties of aggregates Assessment of fines. Grading of filler aggregates (air jet sieving) |
ASTM D 7070 : 2016 : REDLINE | Standard Test Methods for Creep of Rock Core Under Constant Stress and Temperature |
ASTM D 5298 : 2016 : REDLINE | Standard Test Method for Measurement of Soil Potential (Suction) Using Filter Paper |
BS EN ISO 22476-5:2012 | Geotechnical investigation and testing. Field testing Flexible dilatometer test |
BS EN 933-8 : 2012 | TESTS FOR GEOMETRICAL PROPERTIES OF AGGREGATES - PART 8: ASSESSMENT OF FINES - SAND EQUIVALENT TEST |
BS 8550:2010 | Guide for the auditing of water quality sampling |
BS 7755-3.11:1995 | Soil quality. Chemical methods Determination of water-soluble and acid-soluble sulfate |
ASTM D 3967 : 2016 : REDLINE | Standard Test Method for Splitting Tensile Strength of Intact Rock Core Specimens |
BS EN 1744-3:2002 | Tests for chemical properties of aggregates Preparation of eluates by leaching of aggregates |
BS 1377-8:1990 | Methods of test for soils for civil engineering purposes Shear strength tests (effective stress) |
BS EN 13636:2004 | Cathodic protection of buried metallic tanks and related piping |
BS 1377-2:1990 | Methods of test for soils for civil engineering purposes Classification tests |
BS EN 932-3:1997 | Tests for general properties of aggregates Procedure and terminology for simplified petrographic description |
BS ISO 10381-2:2002 | Soil quality. Sampling Guidance on sampling techniques |
BS EN 932-6:1999 | Tests for general properties of aggregates Definitions of repeatability and reproducibility |
BS EN ISO 10545-8:2014 | Ceramic tiles Determination of linear thermal expansion |
BS 7361-1:1991 | Cathodic protection Code of practice for land and marine applications |
BS EN 933-3:2012 | Tests for geometrical properties of aggregates Determination of particle shape. Flakiness index |
BS 10175(2011) : 2011 | INVESTIGATION OF POTENTIALLY CONTAMINATED SITES - CODE OF PRACTICE |
BS EN 1097-4:2008 | Tests for mechanical and physical properties of aggregates Determination of the voids of dry compacted filler |
BS EN ISO 18674-1:2015 | Geotechnical investigation and testing. Geotechnical monitoring by field instrumentation General rules |
ASTM E 1225 : 2013 : REDLINE | Standard Test Method for Thermal Conductivity of Solids Using the Guarded-Comparative-Longitudinal Heat Flow Technique |
BS EN ISO 5667-3:2012 | Water quality. Sampling Preservation and handling of water samples |
BS 22475-2:2011 | Geotechnical investigation and testing. Sampling methods and groundwater measurements Qualification criteria for enterprises and personnel |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.