BS 5255:1989
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
Specification for thermoplastics waste pipe and fittings
Hardcopy , PDF
06-06-2019
BS EN 1565-1:2000
BS EN 1519-1:2000
BS EN 1566-1:2000
BS EN 1329-1 : 2014
BS EN 1451-1:2000
BS EN 1455-1:2000
BS EN 1329-1:2000
English
29-09-1989
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Committees responsible
Specification
1. Scope
2. Definitions
3. Materials
4. Appearance
5. Dimensions
6. Physical properties
7. Performance
8. Marking
Appendices
A. Method of test for resistance to elevated
temperature cycling
B. Method of test for stress relief behaviour of
assembled fittings
C. Guidance on quality control testing
Tables
1. Dimensions of pipes and fittings of ABS, MUPVC and
PP
2. Dimensions of pipes and fittings of PE and of ring
seal sockets for use with PE pipe
3. Dimensions of joint sockets for use with pipes
complying with the dimensions given in table 1
4. Longitudinal reversion of pipes
5. Applicability of requirements and test methods
Figures
1. Pipe lengths
2. Socket dimensions for fittings
3. Bends and equal branches
4. Unequal branches
5. Reducers
6. Straight coupling (with or without register)
7. Socket plugs (with or without access cap)
8. Adaptors
9. Expansion fittings (solvent joint systems)
10. Typical caulking bush
11. Typical installation and test assembly for elevated
temperature cycling test
Dimensions and performance for pipes and fittings made of ABS, MUPVC, PE or PP in nominal sizes of 1¼/32, 1½/40 and 2/50 for the conveyance of domestic effluent.
| Committee |
PRI/88
|
| DevelopmentNote |
Supersedes BS 5255(1976) & 86/43672 DC. (07/2005) Reviewed and confirmed by BSI, December 2009. (11/2009)
|
| DocumentType |
Standard
|
| Pages |
22
|
| PublisherName |
British Standards Institution
|
| Status |
Withdrawn
|
| SupersededBy | |
| Supersedes |
| BS 4778-1:1987 | Quality vocabulary International terms |
| BS 4118:1981 | Glossary of sanitation terms |
| BS 6209:1982 | Specification for solvent cement for non-pressure thermoplastics pipe systems |
| BS 4778-2:1979 | Quality vocabulary National terms |
| BS 2782-11:Method 1101A:1981 | Methods of testing plastics. Thermoplastics pipes, fittings and valves Measurement of dimensions of pipes |
| BS 3943:1979 | Specification for plastics waste traps |
| BS 2782-11:Method 1108A:1989 | Methods of testing plastics. Thermoplastics pipes, fittings and valves True impact rate (TIR) boundaries of pipes |
| BS 2782-11 Method 1102A:1981 | Methods of testing plastics. Thermoplastics pipes, fittings and valves Longitudinal reversion of pipes: immersion bath method |
| BS 3380:1982 | Specification for wastes (excluding skeleton sink wastes) and bath overflows |
| BS 2782-11:Method 1109A:1989 | Methods of testing plastics. Thermoplastics pipes, fittings and valves Resistance to environmental stress cracking of polyethylene pipes and fittings for non-pressure applications |
| BS 2782-11 Method 1103A:1982 | Methods of testing plastics. Thermoplastics pipes, fittings and valves Stress relief test for injection moulded fittings: oven method |
| BS 2782-1 Methods 120A to 120E:1976 | Methods of testing plastics. Thermal properties Determination of the Vicat softening temperature of thermoplastics |
| BS 5254:1976 | Specification for polypropylene waste pipe and fittings (external diameter 34.6 mm, 41.0 mm and 54.1 mm) |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
| BS 2782-11:Method 1112A:1989 | Methods of testing plastics. Thermoplastics pipes, fittings and valves Leaktightness of thermoplastics pipes and fittings for non-pressure applications |
| BS 2782-11 Method 1102B:1981 | Methods of testing plastics. Thermoplastics pipes, fittings and valves Longitudinal reversion of pipes: oven method |
| BS 1755-1:1982 | Glossary of terms used in the plastics industry Polymer and plastics technology |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.