Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS 4660:2000

Withdrawn

Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

View Superseded by

Thermoplastics ancillary fittings of nominal sizes 110 and 160 for below ground gravity drainage and sewerage

Available format(s)

Hardcopy , PDF

Withdrawn date

26-04-2022

Language(s)

English

Published date

10-12-2002

$319.77
Including GST where applicable

Committees responsible
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Materials
5 Appearance
6 Dimensions
7 Physical properties
8 Performance characteristics
9 Marking
Annex A (normative) Method of test for the impact
                    resistance of polyolefin fittings
Annex B (normative) Method of test for water seal
Annex C (informative) Guidance on quality control testing
Bibliography
Figure 1 - Typical channel fittings
Table C.1 - Applicability of requirements and test
            methods

Defines requirements for thermoplastics ancillary access fittings for constructing gravity drains and sewers, other than conventional couplers, bends and branches included in BS EN 1401-1:1998. Covers access fittings of nominal sizes 110 to 160 along with necessary joints and accessories. Test methods, guidance and information on quality control tests are provided.

Committee
PRI/88
DevelopmentNote
Supersedes BS 4660(1989). (12/1999) Supersedes 99/121346 DC. (01/2003) Reviewed and confirmed by BSI, June 2007. (05/2007)
DocumentType
Standard
Pages
16
PublisherName
British Standards Institution
Status
Withdrawn
SupersededBy

This British Standard specifies requirements for thermoplastics ancillary access fittings suitable for the construction of gravity drains and sewers, other than conventional branches, bends and couplers which are covered in BS EN 1401-1:1998. It is applicable to access fittings with nominal sizes of 110 and 160 together with necessary joints and accessories.

Methods of test, associated guidance and information on quality control testing are given in Annex A, Annex B and Annex C.

BS EN 1610:2015 Construction and testing of drains and sewers
BS 2782-11:Method 1121B:1997 Methods of testing plastics. Thermoplastics pipes, fittings and valves Thermoplastics pipes for the conveyance of fluids. Nominal outside diameters and nominal pressures. Metric series
BS EN 752-2:1997 Drain and sewer systems outside buildings Performance requirements
BS EN 1253-2:2015 Gullies for buildings Roof drains and floor gullies without trap
BS EN 681-1:1996 Elastomeric seals. Material requirements for pipe joint seals used in water and drainage applications Vulcanized rubber
BS 6209:1982 Specification for solvent cement for non-pressure thermoplastics pipe systems
BS 5955-6:1980 Plastics pipework (thermoplastics materials) Code of practice for the installation of unplasticized PVC pipework for gravity drains and sewers
BS EN 744:1996 Plastics piping and ducting systems. Thermoplastics pipes. Test method for resistance to external blows by the round-the-clock method
BS 2782-11:Method 1101A:1981 Methods of testing plastics. Thermoplastics pipes, fittings and valves Measurement of dimensions of pipes
BS 3943:1979 Specification for plastics waste traps
BS ISO 472:1988 Plastics. Vocabulary
DD ENV 1401-2:2001 Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinylchloride) (PVC-U) Guidance for assessment of conformity
BS EN 752-3:1997 Drain and sewer systems outside buildings Planning
BS 2782-11:Method 1109A:1989 Methods of testing plastics. Thermoplastics pipes, fittings and valves Resistance to environmental stress cracking of polyethylene pipes and fittings for non-pressure applications
BS EN 1277:2003 Plastics piping systems. Thermoplastics piping systems for buried non-pressure applications. Test methods for leaktightness of elastomeric sealing ring type joints
BS 5834-2:1983 Surface boxes, guards and underground chambers for gas and waterworks purposes Specification for small surface boxes
BS EN ISO 9002:1994 Quality systems. Model for quality assurance in production, installation and servicing
BS EN 1401-1:2009 Plastic piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U) Specifications for pipes, fittings and the system
BS EN 1053:1996 Plastics piping systems. Thermoplastics piping systems for non-pressure applications. Test methods for watertightness
BS EN 752-1:1996 Drain and sewer systems outside buildings Generalities and definitions

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more