ASTM G 85 : 2011 : REDLINE
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Modified Salt Spray (Fog) Testing
Available format(s)
PDF
Superseded date
29-01-2020
Superseded by
Language(s)
English
Published date
01-05-2011
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 03.02, 2015 Provides forth conditions for five modifications in salt spray (fog) testing for specification purposes.
| Committee |
G 01
|
| DevelopmentNote |
Supersedes ASTM G 43 (12/2001)
|
| DocumentType |
Redline
|
| Pages |
14
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This practice covers and sets forth conditions for five modifications in salt spray (fog) testing for specification purposes. These are in chronological order of their development:
1.1.1 Annex A1, acetic acid-salt spray test, continuous.
1.1.2 Annex A2, cyclic acidified salt spray test.
1.1.3 Annex A3, seawater acidified test, cyclic (SWAAT).
1.1.4 Annex A4, SO2 salt spray test, cyclic.
1.1.5 Annex A5, dilute electrolyte cyclic fog dry test.
1.2 This practice does not prescribe the type of modification, test specimen or exposure periods to be used for a specific product, nor the interpretation to be given to the results.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3.1 Exception—Fahrenheit temperature values are given for information only throughout this practice.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| SAE AS29600B | Connectors, Electrical, Circular, Miniature, Composite, High Density, Quick Coupling, Environment Resistant, Removable Crimp Contacts Associated Hardware, General Specification For |
| SAE AIR 5479 : 2017 | ENVIRONMENTALLY COMPLIANT PROCESSES FOR LANDING GEAR |
| MIL-PRF-32577 Base Document:2017 | Coating System, Nonskid, Metallic Thermal Spray Application |
| ASTM D 7087 : 2005 : REV A : R2010 | Standard Test Method for An Imaging Technique to Measure Rust Creepage at Scribe on Coated Test Panels Subjected to Corrosive Environments (Withdrawn 2019) |
| SAE AS12500 | Corrosion Prevention and Deterioration Control in Electronic Components and Assemblies |
| SAE AMS4459A | Aluminum Alloy, Extrusion 2.7Cu - 1.8Li - 0.7Zn - 0.3Mn - 0.3Mg - 0.08Zr (2099-T81) Solution Heat Treated, Stress Relieved by Stretching 1 to 3% and Aged |
| SAE AMS4287A | Aluminum Alloy, Extrusion 2.7Cu - 1.8Li - 0.7Zn - 0.3Mn - 0.3Mg - 0.08Zr (2099-T83) Solution Heat Treated, Stress Relieved by Stretching 1% to 4% and Aged |
| ASTM D 7893 : 2013 | Standard Guide for Corrosion Test Panel Preparation, Testing, and Rating of Coil-Coated Building Products |
| ASTM G 39 : 1999 : R2016 | Standard Practice for Preparation and Use of Bent-Beam Stress-Corrosion Test Specimens |
| ASTM G 112 : 1992 : R2015 | Standard Guide for Conducting Exfoliation Corrosion Tests in Aluminum Alloys |
| ASTM B 456 : 2017 : REDLINE | Standard Specification for Electrodeposited Coatings of Copper Plus Nickel Plus<brk/> Chromium and Nickel Plus Chromium |
| ASTM D 5894 : 2016 : REDLINE | Standard Practice for Cyclic Salt Fog/UV Exposure of Painted Metal, (Alternating Exposures in a Fog/Dry Cabinet and a UV/Condensation Cabinet) |
| SAE AMS3379 | Sealing Compound, Polysulfide Rubber Preformed Strips for Sealing Removable Doors, Skins, and Panels |
| ASTM G 198 : 2017 : REDLINE | Standard Test Method for Determining the Relative Corrosion Performance of Driven Fasteners in Contact with Treated Wood |
| ASTM D 1654 : 2008 : R2016 | Standard Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments |
| 15/30333168 DC : 0 | BS EN 6118 - AEROSPACE SERIES - PROCESS SPECIFICATION - ALUMINIUM BASE PROTECTION FOR FASTENERS |
| DEFSTAN 95-33/1(2004) : 2004 | ALUMINIUM ALLOY (7019) FOR STRUCTURAL (NON-ARMOUR) APPLICATIONS |
| ASME A112.18.1 : 2012 | PLUMBING SUPPLY FITTINGS |
| DEFSTAN 95-19/3(2004) : 2004 | ARMOUR HOMOGENEOUS ALUMINIUM ALLOY, HEAT TREATABLE, EXTRUSIONS AND FORGINGS (6 MM THICK AND OVER) |
| ASME A112.18.1 : 2012 : R2017 | PLUMBING SUPPLY FITTINGS |
| DEFSTAN 95-32/2(2004) : 2004 | ALUMINIUM ALLOY ARMOUR EXTRUSIONS AND FORGINGS (7019) |
| DEFSTAN 95-31/2(2004) : 2004 | ALUMINIUM ALLOY ARMOUR PLATE (7019) |
| DEFSTAN 95-22/4(2004) : 2004 | ALUMINIUM ALLOY ARMOUR PLATE (HEAT TREATABLE 6-120 MM) |
| BS EN 50483-6:2009 | Test requirements for low voltage aerial bundled cable accessories Environmental testing |
| SAE AMS 4257 : 2014 | ALUMINUM ALLOY, EXTRUSION 3.7CU - 1.15LI - 0.5ZN - 0.45AG - 0.4MG - 0.3MN - 0.1ZR (2055-T84) SOLUTION HEAT TREATED, STRESS RELIEVED BY STRETCHING 2% TO 5% AND AGED |
| ASTM G 39 : 1999 : R2005 | Standard Practice for Preparation and Use of Bent-Beam Stress-Corrosion Test Specimens |
| MIL-STD-1678-3 Revision C:2016 | FIBER OPTIC CABLING SYSTEMS REQUIREMENTS AND MEASUREMENTS - PART 3: PHYSICAL, MECHANICAL, ENVIRONMENTAL AND MATERIAL MEASUREMENTS (PART 3 OF 6 PARTS) |
| TT-P-2756 Revision A:1996 | POLYURETHANE COATING - SELF-PRIMING TOPCOAT, LOW VOLATILE ORGANIC COMPOUND (VOC) CONTENT |
| ASTM G 39 : 1999 : R2011 | Standard Practice for Preparation and Use of Bent-Beam Stress-Corrosion Test Specimens |
| ASTM B 733 : 2015 : REDLINE | Standard Specification for Autocatalytic (Electroless) Nickel-Phosphorus Coatings on Metal |
| SAE AIR5919B | Alternatives to Cadmium Plating |
| ASTM G 112 : 1992 : R2003 | Standard Guide for Conducting Exfoliation Corrosion Tests in Aluminum Alloys |
| ASTM G 112 : 1992 : R1997 | Standard Guide for Conducting Exfoliation Corrosion Tests in Aluminum Alloys |
| ASTM G 112 : 1992 : R2009 | Standard Guide for Conducting Exfoliation Corrosion Tests in Aluminum Alloys |
| ASTM D 1654 : 2008 | Standard Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments |
| SAE AMS4458A | Aluminum Alloy, Plate (2.7 Cu - 1.8 Li - 0.7 Zn) 2099-T86 Solution Heat Treated, Cold Worked and Artificially Aged |
| MIL-PRF-64266 Revision B:2016 | CONNECTORS, FIBER OPTIC, CIRCULAR AND RECTANGULAR, PLUG AND RECEPTACLE STYLE, MULTIPLE REMOVABLE GENDERLESS TERMINI, ENVIRONMENT RESISTING GENERAL SPECIFICATION FOR |
| SSPC-PA 12 : 2012 | PREPARATION OF UNCONTAMINATED RUSTED STEEL TEST PANELS |
| IEEE 1478-2013 | IEEE Standard for Environmental Conditions for Transit Railcar Electronic Equipment |
| SAE AMS4251B | Aluminum Alloy Sheet 2.7Cu - 2.2Li - 0.12Zr (2090-T83) Solution Heat Treated, Cold Worked, and Precipitation Heat Treated |
| ASTM D 1654 : 2008 : R2016 : EDT 1 | Standard Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments |
| I.S. EN 50483-6:2009 | TEST REQUIREMENTS FOR LOW VOLTAGE AERIAL BUNDLED CABLE ACCESSORIES - PART 6: ENVIRONMENTAL TESTING |
| GEIA HB 0005-2 : 2007 | TECHNICAL GUIDELINES FOR AEROSPACE AND HIGH PERFORMANCE ELECTRONIC SYSTEMS CONTAINING LEAD-FREE SOLDER AND FINISHES |
| NASA STD 6012 : 2012 | CORROSION PROTECTION FOR SPACE FLIGHT HARDWARE |
| MIL-HDBK-516 Revision C:2014 | AIRWORTHINESS CERTIFICATION CRITERIA |
| JSSG-2006 Base Document:1998 | JOINT SERVICE SPECIFICATION GUIDE - AIRCRAFT STRUCTURES |
| SAE AMS4232C | Aluminum Alloy Extrusions 2.7Cu - 2.2Li - 0.12Zr (2090-T86) Solution Heat Treated, Cold Worked, and Precipitation Heat Treated |
| CSA B125.1:2012 | PLUMBING SUPPLY FITTINGS |
| BS EN ISO 14713-1:2017 | Zinc coatings. Guidelines and recommendations for the protection against corrosion of iron and steel in structures General principles of design and corrosion resistance |
| DIN EN ISO 14713-1:2010-05 | ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 1: GENERAL PRINCIPLES OF DESIGN AND CORROSION RESISTANCE (ISO 14713-1:2017) |
| PREN 14592 : DRAFT 2017 | TIMBER STRUCTURES - DOWEL-TYPE FASTENERS - REQUIREMENTS |
| MIL-PRF-24623-7 Revision A:2013 | SPLICE, MECHANICAL, SIMPLEX FIBER OPTIC CABLE, AIRCRAFT |
| ADS-13F-HDBK : 1997 | AERONAUTICAL DESIGN STANDARD - HANDBOOK - AIR VEHICLE MATERIALS AND PROCESSES |
| SAE AMS4303C | Aluminum Alloy Plate 2.7Cu - 2.2Li - 0.12Zr (2090-T81) Solution Heat Treated, Cold Worked, and Aged |
| SAE ARP5764 | Aerospace Active Inceptor Systems for Aircraft Flight and Engine Controls |
| SAE AMS3603A | Protective Film, High Performance, Polymeric Pressure Sensitive Adhesive, for Aircraft Exterior Applications |
| ASTM D 7087 : 2005 | Standard Test Method for An Imaging Technique to Measure Rust Creepage at Scribe on Coated Test Panels Subjected to Corrosive Environments |
| SAE AMS4359 | Aluminum Alloy, Extruded Profiles (2395-T84) 3.95Cu - 1.15Li - 0.3Ag - 0.5Mg - 0.1Zr Solution Heat Treated, Stress Relieved by Stretching, and Aged |
| ISO 14713-1:2017 | Zinc coatings — Guidelines and recommendations for the protection against corrosion of iron and steel in structures — Part 1: General principles of design and corrosion resistance |
| IEC TS 62647-22:2013 | Process management for avionics - Aerospace and defence electronic systems containing lead-free solder - Part 22: Technical guidelines |
| IEC PAS 62647-22:2011 | Process management for avionics - Aerospace and defence electronic systems containing lead-free solder - Part 22: Technical guidelines |
| EN ISO 14713-1:2017 | Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 1: General principles of design and corrosion resistance (ISO 14713-1:2017) |
| MIL-C-29600 Base Document:1989 | CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, COMPOSITE, HIGH DENSITY, QUICK COUPLING, ENVIRONMENT RESISTANT, REMOVABLE, CRIMP CONTACTS, ASSOCIATED HARDWARE GENERAL SPECIFICATION FOR |
| ASTM D 7087 : 2005 : REV A | Standard Test Method for An Imaging Technique to Measure Rust Creepage at Scribe on Coated Test Panels Subjected to Corrosive Environments |
| SAE AMS4259B | Aluminum Alloy, Sheet 2.4Li - 1.3Cu - 0.95Mg - 0.10Zr (8090-T6) Solution and Precipitation Heat Treated (Unrecrystallized) |
| SAE AS5127/1C | Aerospace Standard Test Methods for Aerospace Sealants Two-Component Synthetic Rubber Compounds |
| I.S. EN ISO 14713-1:2017 | ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 1: GENERAL PRINCIPLES OF DESIGN AND CORROSION RESISTANCE (ISO 14713-1:2017) |
| UNE-EN ISO 14713-1:2017 | Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 1: General principles of design and corrosion resistance (ISO 14713-1:2017) |
| CEI EN 50483-6 : 2011 | TEST REQUIREMENTS FOR LOW VOLTAGE AERIAL BUNDLED CABLE ACCESSORIES - PART 6: ENVIRONMENTAL TESTING |
| SAE AMS3144 | Primer, Anodic Electrodeposition for Aircraft Applications |
| MIL-STD-1568 Revision D:2015 | Materials and Processes for Corrosion Prevention and Control in Aerospace Weapons Systems |
| ASTM D 6577 : 2015 : REDLINE | Standard Guide for Testing Industrial Protective Coatings |
| ASTM G 39 : 1999 | Standard Practice for Preparation and Use of Bent-Beam Stress-Corrosion Test Specimens |
| NACE TM 01 04 : 2004 | OFFSHORE PLATFORM BALLAST WATER TANK COATING SYSTEM EVALUATION |
| ASTM B 994/B994M : 2015 | Standard Specification for Nickel-Cobalt Alloy Coating |
| ASTM G 43 : 1975 : R1980 | Method of Acidified Synthetic Sea Water (Fog) Testing (Withdrawn 1987) |
| PD IEC/TS 62647-22:2013 | Process management for avionics. Aerospace and defence electronic systems containing lead-free solder Technical guidelines |
| EN 50483-6:2009 | Test requirements for low voltage aerial bundled cable accessories - Part 6: Environmental testing |
| AHRI 1361 (SI) : 2017 | PERFORMANCE RATING OF COMPUTER AND DATA PROCESSING ROOM AIR CONDITIONERS |
| AHRI 210/240 : 2006 | PERFORMANCE RATING OF UNITARY AIR-CONDITIONING AND AIR-SOURCE HEAT PUMP EQUIPMENT |
| AHRI 340/360 (I-P) : 2015 | PERFORMANCE RATING OF COMMERCIAL AND INDUSTRIAL UNITARY AIR-CONDITIONING AND HEAT PUMP EQUIPMENT |
| AHRI 1360 (I-P) : 2017 | PERFORMANCE RATING OF COMPUTER AND DATA PROCESSING ROOM AIR CONDITIONERS |
| PREN 6118 : DRAFT 2016 | AEROSPACE SERIES - PROCESS SPECIFICATION - ALUMINIUM BASE PROTECTION FOR FASTENERS |
| ASTM D 1141 : 1998 : EDT 1 | Standard Practice for the Preparation of Substitute Ocean Water |
| ASTM D 609 : 2017 : REDLINE | Standard Practice for Preparation of Cold-Rolled Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products |
| ASTM E 70 | TEST METHOD FOR PH OF AQUEOUS SOLUTIONS WITH THE GLASS ELECTRODE |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.