ASTM G 65 : 2016 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus
Hardcopy , PDF
10-01-2022
English
30-11-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
G 02
|
| DocumentType |
Test Method
|
| Pages |
14
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers laboratory procedures for determining the resistance of metallic materials to scratching abrasion by means of the dry sand/rubber wheel test. It is the intent of this test method to produce data that will reproducibly rank materials in their resistance to scratching abrasion under a specified set of conditions.
1.2Abrasion test results are reported as volume loss in cubic millimetres for the particular test procedure specified. Materials of higher abrasion resistance will have a lower volume loss.
Note 1:In order to attain uniformity among laboratories, it is the intent of this test method to require that volume loss due to abrasion be reported only in the metric system as cubic millimetres. 1 mm3 = 6.102 × 10−5 in3.
1.3This test method covers five recommended procedures which are appropriate for specific degrees of wear resistance or thicknesses of the test material.
1.3.1Procedure A—This is a relatively severe test which will rank metallic materials on a wide volume loss scale from low to extreme abrasion resistance. It is particularly useful in ranking materials of medium to extreme abrasion resistance.
1.3.2Procedure B—A short-term variation of Procedure A. It may be used for highly abrasive resistant materials but is particularly useful in the ranking of medium- and low-abrasive-resistant materials. Procedure B should be used when the volume–loss values developed by Procedure A exceeds 100 mm3.
1.3.3Procedure C—A short-term variation of Procedure A for use on thin coatings.
1.3.4Procedure D—This is a lighter load variation of Procedure A which is particularly useful in ranking materials of low-abrasion resistance. It is also used in ranking materials of a specific generic type or materials which would be very close in the volume loss rates as developed by Procedure A.
1.3.5Procedure E—A short-term variation of Procedure B that is useful in the ranking of materials with medium- or low-abrasion resistance.
1.4This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM B 611 : 2013 : R2018 | Standard Test Method for Determining the High Stress Abrasion Resistance of Hard Materials |
| ASTM D 2000 : 2003 : REV A : EDT 1 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2000 : 2001 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2240 : 2000 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM E 177 : 1990 : REV A : R1996 | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
| ASTM G 40 : 2021 | Standard Terminology Relating to Wear and Erosion |
| ASTM D 2000 : 2000 : EDT 1 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2000 : 2003 : REV A | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2240 : 2004 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 2240 : 2004 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 2000 : 2008 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2000 : 2006 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2000 : 2006 : REV A | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM G 40 : 2021 : REV A | Standard Terminology Relating to Wear and Erosion |
| ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 2240 : 2015 : R2021 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 2000 : 2005 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2000 : 2018 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2240 : 2002 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 2000 : 2006 : REV A : EDT 1 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2240 : 2015 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 2000 : 2012 : R2017 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2240 : 2003 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 2240 : 2002 : REV B | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 2240 : 2015 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 2240 : 2005 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 2000 : 2004 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2240 : 2005 : R2010 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM G 40 : 2017 | Standard Terminology Relating to Wear and Erosion |
| ASTM D 2240 : 2002 : REV A | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 2000 : 2012 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2000 : 2003 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2000 : 2000 | Standard Classification System for Rubber Products in Automotive Applications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.