ASTM G 61 : 1986 : R2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Conducting Cyclic Potentiodynamic Polarization Measurements for Localized Corrosion Susceptibility of Iron-, Nickel-, or Cobalt-Based Alloys
Hardcopy , PDF
24-05-2024
English
01-05-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
G 01
|
| DocumentType |
Test Method
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers a procedure for conducting cyclic potentiodynamic polarization measurements to determine relative susceptibility to localized corrosion (pitting and crevice corrosion) for iron-, nickel-, or cobalt-based alloys in a chloride environment. This test method also describes an experimental procedure which can be used to check one's experimental technique and instrumentation.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM B 1015 : 2020 | Standard Practice for Form and Style of Standards Relating to Refined Nickel and Cobalt and Their Alloys |
| ASTM G 46 : 2021 | Standard Guide for Examination and Evaluation of Pitting Corrosion |
| ASTM F 1875 : 1998 : R2022 | Standard Practice for Fretting Corrosion Testing of Modular Implant Interfaces: Hip Femoral Head-Bore and Cone Taper Interface |
| ASTM F 2129 : 2019 : REV A | Standard Test Method for Conducting Cyclic Potentiodynamic Polarization Measurements to Determine the Corrosion Susceptibility of Small Implant Devices |
| ASTM G 192 : 2008 : R2020 : EDT 1 | Standard Test Method for Determining the Crevice Repassivation Potential of Corrosion-Resistant Alloys Using a Potentiodynamic-Galvanostatic-Potentiostatic Technique |
| ASTM G 199 : 2009 : R2020 : EDT 1 | Standard Guide for Electrochemical Noise Measurement |
| ASTM G 108 : 2023 | Standard Test Methods for Electrochemical Reactivation (EPR) for Detecting Sensitization of AISI Type 304 and 304L Stainless Steels |
| NACE SP21469:2021 | Corrosion Inhibition Selection and Management for Oil and Gas Production |
| ASTM G 3 : 2014 : R2024 | Standard Practice for Conventions Applicable to Electrochemical Measurements in Corrosion Testing |
| ASTM G 5 : 1994 | Standard Reference Test Method for Making Potentiostatic and Potentiodynamic Anodic Polarization Measurements |
| ASTM G 5 : 1994 : R1999 | Standard Reference Test Method for Making Potentiostatic and Potentiodynamic Anodic Polarization Measurements |
| ASTM G 5 : 2014 : EDT 1 | Standard Reference Test Method for Making Potentiodynamic Anodic Polarization Measurements |
| ASTM G 3 : 2014 : R2019 | Standard Practice for Conventions Applicable to Electrochemical Measurements in Corrosion Testing |
| ASTM G 5 : 2014 : R2021 | Standard Reference Test Method for Making Potentiodynamic Anodic Polarization Measurements |
| ASTM D 1193 : 1970 | Standard Specification For Reagent Water |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.