ASTM F 970 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Measuring Recovery Properties of Floor Coverings after Static Loading
Hardcopy , PDF
05-11-2022
English
02-11-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.This test method is intended for use in determining the recovery properties of uninstalled resilient floor covering after long-term indentation test, 24 h under the load specified in the detail specification.
| Committee |
F 06
|
| DocumentType |
Test Method
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method is intended for use in determining the recovery properties of uninstalled resilient floor covering after long-term indentation test, 24 h under the load specified in the detail specification. The reported value, residual indentation, is the depth of the depression remaining 24 h after removal of the specified load.
1.2This test method is not intended for use in evaluating the long-term indentation resistance or recovery properties, or both, of resilient floor coverings at loads above those listed in the Precision and Bias statement as described in Section 10.
1.2.1Testing at loads above 250 psi is outside the scope of this test method.
1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 3261 : 2020 | Standard Specification for Resilient Flooring in Modular Format with Rigid Polymeric Core |
| ASTM F 3041 : 2014 : R2019 | Standard Specification for Bonded Rubber Crumb Floor Coverings |
| ASTM F 2195 : 2018 | Standard Specification for Linoleum Floor Tile |
| ASTM F 1913 : 2019 | Standard Specification for Vinyl Sheet Floor Covering Without Backing |
| ASTM F 1344 : 2021 : REV A | Standard Specification for Rubber Floor Tile |
| ASTM F 1860 : 2021 : REV A | Standard Specification for Rubber Sheet Floor Covering With Backing |
| ASTM F 1303 : 2004 : R2021 | Standard Specification for Sheet Vinyl Floor Covering with Backing |
| ASTM F 3008 : 2013 : R2020 | Standard Specification for Cork Floor Tile |
| ASTM F 2034 : 2018 | Standard Specification for Sheet Linoleum Floor Covering |
| ASTM F 1859 : 2021 : REV A | Standard Specification for Rubber Sheet Floor Covering Without Backing |
| ASTM F 2982 : 2018 | Standard Specification for Polyester Composition Floor Tile |
| ASTM F 3404 : 2021 : EDT 1 | Standard Specification for Heterogeneous Polyurethane Tile or Plank Flooring |
| ASTM F 3403 : 2021 : EDT 1 | Standard Specification for Heterogeneous Polyurethane Sheet Flooring |
| ASTM F 3261 : 2020 | Standard Specification for Resilient Flooring in Modular Format with Rigid Polymeric Core |
| ASTM F 1914 : 2006 | Standard Test Methods for Short-Term Indentation and Residual Indentation of Resilient Floor Covering |
| ASTM F 386 : 2017 | Standard Test Method for Thickness of Resilient Flooring Materials Having Flat Surfaces |
| ASTM F 1914 : 2018 | Standard Test Methods for Short-Term Indentation and Residual Indentation of Resilient Floor Covering |
| ASTM F 1914 : 2007 : R2011 | Standard Test Methods for Short-Term Indentation and Residual Indentation of Resilient Floor Covering |
| ASTM F 1914 : 2007 | Standard Test Methods for Short-Term Indentation and Residual Indentation of Resilient Floor Covering |
| ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM F 387 : 2017 | Standard Test Method for Measuring Thickness of Resilient Floor Covering With Foam Layer |
| ASTM F 1914 : 2005 | Standard Test Method for Short-Term Indentation and Residual Indentation of Resilient Floor Covering |
| ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM F 1914 : 2017 | Standard Test Methods for Short-Term Indentation and Residual Indentation of Resilient Floor Covering |
| ASTM F 386 : 2017 : R2022 | Standard Test Method for Thickness of Resilient Flooring Materials Having Flat Surfaces |
| ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM F 387 : 2017 : R2022 | Standard Test Method for Measuring Thickness of Resilient Floor Covering With Foam Layer |
| ASTM F 1914 : 1998 | Standard Test Method for Short-Term Indentation and Residual Indentation of Resilient Floor Covering |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.