ASTM F 477 : 2014 : REDLINE
Current
Current
The latest, up-to-date edition.
Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
Available format(s)
PDF
Language(s)
English
Published date
15-09-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 08.04, 2018 Specifies elastomeric seals (gaskets) used to seal the joints of plastic pipe used for gravity, low-pressure, and high-pressure applications.
| Committee |
F 17
|
| DocumentType |
Redline
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
1.1This specification covers elastomeric seals (gaskets) used to seal the joints of plastic pipe used for gravity, low-pressure, and high-pressure applications. This refers to push-on joints which require no internal or external pressure to effect the initial seal.
1.2Requirements are given for natural or synthetic rubber gaskets, or a combination of both.
1.3The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.4The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 3139 : 1998 : R2011 | Standard Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals |
| ASTM F 1987 : 2001 | Standard Specification for Multilayer Pipe Type 2 , Compression Fittings, and Compression Joints for Hydronic Heating Systems |
| ASTM D 3517 : 2014 : REDLINE | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe |
| ASTM D 3262 : 2016 : REDLINE | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer Pipe |
| ASTM F 1901 : 2016 : REDLINE | Standard Specification for Polyethylene (PE) Pipe and Fittings for Roof Drain Systems |
| ASTM F 794:2003 | Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter |
| ASTM F 794 : 2003 : R2014 | Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter |
| ASTM D 3754 : 2014 : REDLINE | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe |
| ASTM D 6783 : 2005 | Standard Specification for Polymer Concrete Pipe |
| ASTM F 2881 : 2011 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications |
| ASTM F 2946 : 2012 : R2017 | Standard Specification for PVC Hub and Elastomeric Seal (Gasket) Tee Connection for Joining Plastic Pipe to Insitu Pipelines and Manholes |
| ASTM F 2881 : 2011 : R2015 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications |
| ASTM D 3212 : 2007 : R2013 | Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals |
| ASTM F 892 : 1995 | Specification for Polyethylene (PE) Corrugated Pipe With a Smooth Interior and Fittings (Withdrawn 2001) |
| ASTM F 2737 : 2011 : R2017 | Standard Specification for Corrugated High Density Polyethylene (HDPE) Water Quality Units |
| ASTM F 2762 : 2011 : EDT 1 | Standard Specification for 12 to 30 in. (300 to 750 mm) Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications (Withdrawn 2016) |
| ASTM F 2947 : 2012 | Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM F 2763 : 2016 : REDLINE | Standard Specification for 12 to 60 in. [300 to 1500 mm] Dual and Triple Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM F 1759 : 1997 : R2004 | Standard Practice for Design of High-Density Polyethylene (HDPE) Manholes for Subsurface Applications |
| ASTM F 3058 : 2016 | Standard Practice for Preliminary Field Testing of Thermoplastic Pipe Joints for Gravity Flow (Non-Pressure) Sewer Lines |
| ASTM D 2680 : 2001 : R2014 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping |
| ASTM D 3139 : 1998 : R2005 | Standard Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals |
| ASTM F 1986 : 2001 : R2011 | Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hot and Cold Drinking-Water Systems (Withdrawn 2020) |
| ICC 2009 INT. RESI.CODE & COMM.-I1 : 2009 | 2009 INTERNATIONAL RESIDENTIAL CODE & COMMENTARY - VOLUME 2: CHAPTERS 12 TO 44 |
| AWWA M45 : 3 | FIBERGLASS PIPE DESIGN |
| ASTM F 1759 : 1997 : R2010 | Standard Practice for Design of High-Density Polyethylene (HDPE) Manholes for Subsurface Applications |
| AWWA C908 : 2001 | PVC SELF-TAPPING SADDLE TEES FOR USE ON PVC PIPE |
| ASTM F 679 : 2016 : REDLINE | Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings |
| FM 1614 : 2017 | FIBER REINFORCED COMPOSITE (FRC) PIPE AND FITTINGS FOR UNDERGROUND FIRE PROTECTION SERVICE |
| AASHTO M 304 : 2011 : R2015 | SPECIFICATION FOR POLY(VINYL CHLORIDE) (PVC) PROFILE WALL DRAIN PIPE AND FITTINGS BASED ON CONTROLLED INSIDE DIAMETER |
| ASTM F 1668 : 2016 : REDLINE | Standard Guide for Construction Procedures for Buried Plastic Pipe |
| ASTM F 1336 : 2015 : REDLINE | Standard Specification for Poly(Vinyl Chloride) (PVC) Gasketed Sewer Fittings |
| ASTM D 3212 : 2007 | Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals |
| ASTM F 3219 : 2017 | Standard Specification for 3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated Single Wall Pipe and Fittings |
| ASTM D 2680 : 2001 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping |
| ASTM F 2510/F2510M : 2017 : REDLINE | Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures and Corrugated Dual- and Triple-Wall Polyethylene and Polypropylene Pipes |
| ASTM F 2737 : 2011 | Standard Specification for Corrugated High Density Polyethylene (HDPE) Water Quality Units |
| ASTM F 2762 : 2011 | Standard Specification for 12 to 30 in. [300 to 750 mm] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM F 949 : 2015 : REDLINE | Standard Specification for Poly(Vinyl Chloride) (PVC) Corrugated Sewer Pipe With a Smooth Interior and Fittings |
| ASTM F 2562/F2562M : 2015 : REDLINE | Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage |
| AASHTO M 326 : 2008 | SPECIFICATION FOR POLYETHYLENE (PE) LINER PIPE, 300- TO 1600-MM DIAMETER, BASED ON CONTROLLED OUTSIDE DIAMETER |
| AASHTO M 278 : 2015 | SPECIFICATION FOR CLASS PS46 POLY(VINYL CHLORIDE) (PVC) PIPE |
| ASTM D 2751 : 2005 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings (Withdrawn 2014) |
| ICC 2012 INT. PVT. SEWAGE DISP.CODE : 2012 | INTERNATIONAL PRIVATE SEWAGE DISPOSAL CODE |
| ASTM F 2768 : 2009 | Standard Specification for Modified Stub ACME Thread Joint with Elastomeric Seal in Plastic Piping Components (Withdrawn 2016) |
| AWWA C900 : 2016 | POLYVINYL CHLORIDE (PVC) PRESSURE PIPE AND FABRICATED FITTINGS, 4 IN. THROUGH 60 IN. (100 MM THROUGH 1,500 MM) |
| AASHTO MP 20 : 2013 | SPECIFICATION FOR STEEL-REINFORCED POLYETHYLENE (PE) RIBBED PIPE, 300- TO 1500-MM (12- TO 60-IN.) DIAMETER |
| ASTM F 2947 : 2012 : EDT 1 | Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM F 1483 : 2017 : REDLINE | Standard Specification for Oriented Poly(Vinyl Chloride), PVCO, Pressure Pipe |
| CSA B137 COMPENDIUM : 2017 | THERMOPLASTIC PRESSURE PIPING COMPENDIUM |
| AWWA C905 : 2010 | POLYVINYL CHLORIDE (PVC) PRESSURE PIPE AND FABRICATED FITTINGS, 14 IN. THROUGH 48 IN. (350 MM THROUGH 1,200 MM), FOR WATER TRANSMISSION AND DISTRIBUTION |
| ASTM F 1759 : 1997 : R2018 | Standard Practice for Design of High-Density Polyethylene (HDPE) Manholes for Subsurface Applications |
| ASTM F 2946 :2012 | Standard Specification for PVC Hub and Elastomeric Seal (Gasket) Tee Connection for Joining Plastic Pipe to Insitu Pipelines and Manholes |
| ASTM F 1760 : 2016 : REDLINE | Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic Pipe Having Reprocessed-Recycled Content |
| ASTM D 6783 : 2005 : REV A : R2017 | Standard Specification for Polymer Concrete Pipe |
| ICC IPC CODE & COMMENTARY : 2015 | IPC® Code and Commentary |
| ICC IRC CODE AND COMMENTARY VOLUME 2 : 2015 | IRC® Code and Commentary, Volume 2 |
| ICC 2012 INTERNATIONAL RESI. CODE : 2012 | INTERNATIONAL RESIDENTIAL CODE FOR ONE- AND TWO-FAMILY DWELLINGS |
| ICC 2012 INTERNATIONAL PLUMBING CODE : 2012 | INTERNATIONAL PLUMBING CODE (INCLUDES IPSDC) |
| ANSI/AWWA C950:2013 | FIBERGLASS PRESSURE PIPE |
| ASTM D 2680 : 2001 : R2009 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping |
| ASTM D 3840 : 2014 : REDLINE | SPECIFICATION FOR 'FIBERGLASS' (GLASS-FIBER-REINFORCED THERMOSETTING-RESIN) PIPE FITTINGS FOR NONPRESSURE APPLICATIONS |
| DWA-M 143-20:2018 | TEST METHOD FOR DROP IMPACT RESISTANCE OF BLOW-MOLDED THERMOPLASTIC CONTAINERS |
| AASHTO PP 63 : 2009 : R2014 | PRACTICE FOR PIPE JOINT SELECTION FOR HIGHWAY CULVERT AND STORM DRAINS |
| AASHTO MP 20 : 2013 : R2014 | SPECIFICATION FOR STEEL-REINFORCED POLYETHYLENE (PE) RIBBED PIPE, 300- TO 1500-MM (12- TO 60-IN.) DIAMETER |
| AWWA C907 : 2017 | INJECTION-MOLDED POLYVINYL CHLORIDE (PVC) PRESSURE FITTINGS, 4 IN. THROUGH 12 IN. (100 MM THROUGH 300 MM), FOR WATER, WASTEWATER, AND RECLAIMED WATER SERVICE |
| R 82 : 2017 | PRACTICE FOR PIPE JOINT SELECTION FOR HIGHWAY CULVERT AND STORM DRAINS |
| ASTM F 2307 : 2003 | Standard Specification for Series 10 Poly(Vinyl Chloride) (PVC) Closed Profile Gravity Pipe and Fittings Based on Controlled Inside Diameter (Withdrawn 2011) |
| ASTM D3139 : 1998 | Standard Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals |
| FM 1612 : 2016 | POLYVINYL CHLORIDE (PVC) PIPE AND FITTING FOR UNDERGROUND FIRE PROTECTION SERVICE |
| ASTM F 1987 : 2001 : R2011 | Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hydronic Heating Systems (Withdrawn 2020) |
| GOST 849:2018 | Primary nickel. SpecificationsE |
| AWWA M23 : 2 | PVC PIPE - DESIGN AND INSTALLATION |
| ASTM F 1803 : 2015 | Standard Specification for Poly (Vinyl Chloride)(PVC) Closed Profile Gravity Pipe and Fittings Based on Controlled Inside Diameter |
| ASTM F 1866 : 2018 : REDLINE | Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings |
| ASTM F 1986 : 2001 : R2006 | Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hot and Cold Drinking-Water Systems |
| ICC IPSDC INTERNATIONAL PVT. SEWAGE DISPOSAL CODE : 2015 | INTERNATIONAL PRIVATE SEWAGE DISPOSAL CODE |
| AASHTO M 304 : 2011 | SPECIFICATION FOR POLY(VINYL CHLORIDE) (PVC) PROFILE WALL DRAIN PIPE AND FITTINGS BASED ON CONTROLLED INSIDE DIAMETER |
| ASTM F 1759 : 1997 | Standard Practice for Design of High-Density Polyethylene (HDPE) Manholes for Subsurface Applications |
| ASAE S376.1 : 1992 | DESIGN, INSTALLATION AND PERFORMANCE OF UNDERGROUND, THERMOPLASTIC IRRIGATION PIPELINES |
| AASHTO M 294 : 2015 | SPECIFICATION FOR CORRUGATED POLYETHYLENE PIPE, 300- TO 1500-MM (12- TO 60-IN.) DIAMETER |
| NSF 14 : 2016 | PLASTICS PIPING SYSTEM COMPONENTS AND RELATED MATERIALS |
| ASTM D 6783 : 2005 : R2011 | Standard Specification for Polymer Concrete Pipe |
| ASTM F 1986 : 2001 | Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hot and Cold Drinking-Water Systems |
| ASTM F 1987 : 2001 : R2006 | Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hydronic Heating Systems |
| ASTM F 2881/F2881M : 2018 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications |
| ASTM F 2435 : 2015 : REDLINE | Standard Specification for Steel Reinforced Polyethylene (PE) Corrugated Pipe |
| ASTM F 891 : 2016 : REDLINE | Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core |
| ASTM F 2947/F2947M : 2014-03 | SPECIFICATION FOR 150 TO 1500 MM [6 TO 60 IN.] ANNULAR CORRUGATED PROFILE-WALL POLYETHYLENE (PE) PIPE AND FITTINGS FOR SANITARY SEWER APPLICATIONS |
| ASTM A 1107/A1107M : 2017 | Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures and Corrugated Steel Drainage Pipes |
| ASTM F 794 : 2003 : R2009 | Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter |
| ASME A112.4.4 : 2017 | PLASTIC PUSH-FIT DRAIN, WASTE, AND VENT (DWV) FITTINGS |
| NSF 61 : 2016 | DRINKING WATER SYSTEM COMPONENTS - HEALTH EFFECTS |
| NSF 14 : 2016 | PLASTICS PIPING SYSTEM COMPONENTS AND RELATED MATERIALS |
| ASTM D 1149 : 2016-02 | TEST METHODS FOR RUBBER DETERIORATION - CRACKING IN AN OZONE CONTROLLED ENVIRONMENT |
| ASTM D 1414 : 2015 : REDLINE | Standard Test Methods for Rubber O-Rings |
| ASTM D 1349 : 2014 : REDLINE | Standard Practice for Rubber—Standard Conditions for Testing |
| ASTM F 913 : 2002 : EDT 1 | Standard Specification for Thermoplastic Elastomeric Seals (Gaskets) for Joining Plastic Pipe |
| ASTM D 1566 : 2015 : REDLINE | TERMINOLOGY RELATING TO RUBBER |
| ASTM D 471 : 2016-02 | TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.