ASTM F 2854 : 2010 : R2016
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Push-Fit Crosslinked Polyethylene (PEX) Mechanical Fittings for Crosslinked Polyethylene (PEX) Tubing
Available format(s)
Hardcopy , PDF
Superseded date
17-11-2020
Superseded by
Language(s)
English
Published date
26-08-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 08.04, 2017 Defines crosslinked polyethylene (PEX) push-fit mechanical fittings for use with crosslinked polyethylene (PEX) tubing in [1/2], [3/4], 1 and (1[1/4]) in. nominal diameters that meet the requirements of Specification F876.
| Committee |
F 17
|
| DocumentType |
Standard
|
| Pages |
4
|
| ProductNote |
Reconfirmed 2016
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers crosslinked polyethylene (PEX) push-fit mechanical fittings for use with crosslinked polyethylene (PEX) tubing in 1/2, 3/4, 1 and 1 1/4 in. nominal diameters that meet the requirements of Specification F876. These fittings are intended for use in residential and commercial, hot and cold, potable water distribution systems as well as hydronic heating, including under-floor heating systems, up to and including 100 psig (6.90 bar) and 180°F (82°C). Included are the requirements for materials, workmanship, dimensions, performance, and markings to be used on the fittings.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 2000 : 2003 : REV A : EDT 1 | Standard Classification System for Rubber Products in Automotive Applications |
| EN 12168:2016 | Copper and copper alloys - Hollow rod for free machining purposes |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2000 : 2001 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM F 876 : 2017 : REDLINE | SPECIFICATION FOR CROSSLINKED POLYETHYLENE (PEX) TUBING |
| ASTM F 2023 : 2003 | Standard Test Method for Evaluating the Oxidative Resistance of Crosslinked Polyethylene (PEX) Tubing and Systems to Hot Chlorinated Water |
| ASTM D 2765 : 2011 | Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics |
| ASTM D 2122 : 1998 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ASTM F 2023 : 2015 | Standard Test Method for Evaluating the Oxidative Resistance of Crosslinked Polyethylene (PEX) Pipe, Tubing and Systems to Hot Chlorinated Water |
| ASTM F 2023 : 2010 | Standard Test Method for Evaluating the Oxidative Resistance of Crosslinked Polyethylene (PEX) Tubing and Systems to Hot Chlorinated Water |
| ASTM D 6394 : 2014 : REDLINE | Standard Specification for Sulfone Plastics (SP) |
| ASTM D 6284 : 2002 : R2008 : EDT 1 | Standard Test Method for Rubber Property—Effect of Aqueous Solutions with Available Chlorine and Chloramine |
| ASTM D 6284 : 2017 : REDLINE | Standard Test Method for Rubber Property—Effect of Aqueous Solutions with Available Chlorine and Chloramine |
| ASTM D 6284 : 2009 | Standard Test Method for Rubber Property—Effect of Aqueous Solutions with Available Chlorine and Chloramine |
| ASTM D 6394 : 2001 | Standard Specification for Sulfone Plastics (SP) |
| NSF 14 : 2016 | PLASTICS PIPING SYSTEM COMPONENTS AND RELATED MATERIALS |
| ASTM D 2000 : 2000 : EDT 1 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2765 : 2001 : R2006 | Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics |
| ASTM D 2000 : 2003 : REV A | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 6394 : 2003 | Standard Specification for Sulfone Plastics (SP) |
| ASTM F 2023 : 2008 | Standard Test Method for Evaluating the Oxidative Resistance of Crosslinked Polyethylene (PEX) Tubing and Systems to Hot Chlorinated Water |
| ASTM D 6284 : 1998 | Standard Test Method for Rubber Property-Effect of Aqueous Solutions with Available Chlorine and Chloramine |
| ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| ASTM D 1505 : 2003 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| PPI TR 3 : 2017 | POLICIES AND PROCEDURES FOR DEVELOPING HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESSES (HDS), PRESSURE DESIGN BASIS (PDB), STRENGTH DESIGN BASIS (SDB), MINIMUM REQUIRED STRENGTH (MRS) RATINGS, AND CATEGORIZED REQUIRED STRENGTH (CRS) FOR THERMOPLASTIC PIPING MATERIALS OR PIPE |
| ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM F 2023 : 2003 : EDT 1 | Standard Test Method for Evaluating the Oxidative Resistance of Crosslinked Polyethylene (PEX) Tubing and Systems to Hot Chlorinated Water |
| ASTM F 2023 : 2013 | Standard Test Method for Evaluating the Oxidative Resistance of Crosslinked Polyethylene (PEX) Tubing and Systems to Hot Chlorinated Water |
| ASTM F 2023 : 2005 | Standard Test Method for Evaluating the Oxidative Resistance of Crosslinked Polyethylene (PEX) Tubing and Systems to Hot Chlorinated Water |
| ASTM D 1599 : 2014 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1599 : 2014 : EDT 1 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM A 351/A351M : 2016-05 | SPECIFICATION FOR CASTINGS, AUSTENITIC, FOR PRESSURE-CONTAINING PARTS |
| ASTM D 2765 : 2001 | Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics |
| ASTM D 2000 : 2008 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2000 : 2006 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 6394 : 2005 | Standard Specification for Sulfone Plastics (SP) |
| ASTM D 2122 : 1998 : EDT 1 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 6394 : 2014 | Standard Specification for Sulfone Plastics (SP) |
| ASTM D 2000 : 2006 : REV A | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 1599 : 2018 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1599 : 1999 : R2011 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 2000 : 2005 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 1599 : 1999 : EDT 1 | Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 2000 : 2018 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM F 2023 : 2015 : REDLINE | Standard Test Method for Evaluating the Oxidative Resistance of Crosslinked Polyethylene (PEX) Pipe, Tubing and Systems to Hot Chlorinated Water |
| ASTM D 6284 : 2017 | Standard Test Method for Rubber Property—Effect of Aqueous Solutions with Available Chlorine and Chloramine |
| ASTM D 1505 : 1968 : R1979 | Standard Test Method for Density Of Plastics By The Density-Gradient Technique |
| ASTM D 2765 : 2016 : REDLINE | Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 2000 : 2006 : REV A : EDT 1 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 6394 : 2002 | Standard Specification for Sulfone Plastics (SP) |
| ASTM D 2000 : 2012 : R2017 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 6394 : 2011 | Standard Specification for Sulfone Plastics (SP) |
| ASTM D 2122 : 2016 : REDLINE | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| EN 12164:2016 | Copper and copper alloys - Rod for free machining purposes |
| ASTM D 1505 : 2010 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
| ASTM D 1505 : 2018 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
| ASTM D 2122 : 1998 : R2004 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 1505 : 1998 : EDT 1 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
| ASTM D 6394 : 2008 | Standard Specification for Sulfone Plastics (SP) |
| ASTM D 2122 : 2016 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 6394 : 1999 | Standard Specification for Sulfone Plastics (SP) |
| ASTM D 6394 : 2009 | Standard Specification for Sulfone Plastics (SP) |
| ASTM F 2023 : 2009 | Standard Test Method for Evaluating the Oxidative Resistance of Crosslinked Polyethylene (PEX) Tubing and Systems to Hot Chlorinated Water |
| ASTM D 6394 : 2007 | Standard Specification for Sulfone Plastics (SP) |
| ASTM F 2023 : 2004 | Standard Test Method for Evaluating the Oxidative Resistance of Crosslinked Polyethylene (PEX) Tubing and Systems to Hot Chlorinated Water |
| ASTM D 1599 : 1999 : R2005 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM A 276/A276M : 2017 : REDLINE | Standard Specification for Stainless Steel Bars and Shapes |
| ASTM A 312/A312M : 2017-03 | SPECIFICATION FOR SEAMLESS, WELDED, AND HEAVILY COLD WORKED AUSTENITIC STAINLESS STEEL PIPES |
| ASTM D 2000 : 2004 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 6284 : 2002 | Standard Test Method for Rubber Property—Effect of Aqueous Solutions with Available Chlorine and Chloramine |
| EN 12165:2016 | Copper and copper alloys - Wrought and unwrought forging stock |
| ASTM D 2765 : 2016 | Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics |
| ASTM D 2765 : 1995 | Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics |
| ASTM D 2122 : 1998 : R2010 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 6394 : 2010 | Standard Specification for Sulfone Plastics (SP) |
| ASTM F 2023 : 2000 | Standard Test Method for Evaluating the Oxidative Resistance of Crosslinked Polyethylene (PEX) Tubing and Systems to Hot Chlorinated Water |
| ASTM D 2000 : 2012 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 1599 : 1999 | Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 2000 : 2003 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2000 : 2000 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2122 : 2015 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.