ASTM F 2352 : 2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Design and Performance of Light Sport Gyroplane Aircraft
Hardcopy , PDF
14-10-2022
English
25-11-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
F 37
|
| DocumentType |
Standard
|
| Pages |
17
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers the manufacture of gyroplanes. This specification includes design and performance requirements for light sport gyroplane aircraft.
1.2This specification applies to light gyroplane aircraft seeking civil aviation authority approval in the form of flight certificates, flight permits, or other like documentation.
1.3A gyroplane for the purposes of this specification is defined as a rotorcraft to be used for day VFR only, with rotor blades that are not engine-driven in flight and are supported in flight by the reaction of the air on a single rotor that rotates freely on a substantially vertical axis when the aircraft is in horizontal flight.
1.4These requirements apply to light gyroplanes of orthodox design. Aircraft having the following basic features will be so regarded:
1.4.1Rotors of either fixed collective pitch or collective pitch control that are not adjustable in flight,
1.4.2Single engine with fixed or ground adjustable pitch propeller,
1.4.3No more than two occupant seats, and
1.4.4A maximum gross weight (MGW) of 725 kg (1600 lb) or less.
1.5Where it can be shown that a particular feature is similar in all significant respects to a feature that has historically demonstrated compliance with this specification and can be considered a separate entity in terms of its operation, that feature shall be deemed to be applicable and in compliance with this specification.
1.6Where these requirements are inappropriate to particular design and construction features, it will be necessary to submit an appropriate amendment of this specification to ASTM Committee F37 on Light Sport Aircraft for consideration and approval.
1.7The values in SI units are to be regarded as the standard. The values in parentheses are for information only.
1.8This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.9Table of Contents:
| Section | |
| Scope | 1 |
| Table of Contents | 1.9 |
| Referenced Documents | 2 |
| Terminology | 3 |
| Definitions | 3.1 |
| Acronyms | 3.2 |
| Flight | 4 |
| General | 4.1 |
| Performance | 4.2 |
| Controllability and Maneuverability | 4.3 |
| Longitudinal Lateral and Directional Control | 4.4 |
| Stability | 4.5 |
| Ground-Handling Characteristics | 4.6 |
| Miscellaneous Flight Requirements | 4.7 |
| Structure | 5 |
| General | 5.1 |
| Flight Loads | 5.2 |
| Engine Torque | 5.3 |
| Control System Loads | 5.4 |
| Stabilizing and Control Surfaces | 5.5 |
| Ground Loads | 5.6 |
| Main Component Requirements | 5.7 |
| Emergency Landing Conditions | 5.8 |
| Other Loads | 5.9 |
| Design and Construction | 6 |
| General | 6.1 |
| Materials | 6.2 |
| Fabrication Methods | 6.3 |
| Locking of Connections | 6.4 |
| Protection of Structure | 6.5 |
| Inspection | 6.6 |
| Provisions for Rigging and Derigging | 6.7 |
| Material Strength Properties and Design Values | 6.8 |
| Fatigue Strength | 6.9 |
| Special Factors of Safety | 6.10 |
| Bearing Factors | 6.10.2 |
| Fitting Factors | 6.10.3 |
| Cable Factor | 6.10.4 |
| Rotor Components Factor | 6.10.5 |
| Flutter Prevention and Structural Stiffness | 6.11 |
| Control Surfaces and Rotors | 6.12 |
| Control Surface Installations (Other Than Rotor Blades) | 6.13 |
| Control Surface Hinges (Other Than Rotor Blades) | 6.14 |
| Rotor Mass Balance | 6.15 |
| Rotor Blade Clearance | 6.16 |
| Rotor Head Bearings | 6.17 |
| Control Systems | 6.18 |
| Cockpit Design | 6.19 |
| Powerplant | 7 |
| General | 7.1 |
| Engine | 7.2 |
| Engine and Propeller Compatibility | 7.3 |
| Rotor Spin-Up and Brake Systems | 7.4 |
| Powerplant and Rotor System Compatibility | 7.5 |
| Propeller Clearance | 7.6 |
| Fuel System | 7.7 |
| Oil System | 7.8 |
| Cooling | 7.9 |
| Induction System | 7.10 |
| Exhaust System | 7.11 |
| Powerplant Controls and Accessories | 7.12 |
| Cowling and Nacelle | 7.13 |
| Equipment | 8 |
| General | 8.1 |
| Instruments—Installation | 8.2 |
| Electrical Systems and Equipment | 8.3 |
| Miscellaneous Equipment | 8.4 |
| Operating Limitations and Information | 9 |
| General | 9.1 |
| Airspeed Limitations | 9.2 |
| Weight and Balance | 9.3 |
| Powerplant and Propeller Limitations | 9.4 |
| Pilot Operating Handbook, POH | 9.5 |
| Maintenance Manual | 9.6 |
| Markings and Placards | 9.7 |
| Propellers | 10 |
| Design and Construction | 10.1 |
| Keywords | 12 |
| ASTM F 3060 : 2020 | Standard Terminology for Aircraft |
| ASTM F 2507 : 2015 | Standard Specification for Recreational Airpark Design (Withdrawn 2024) |
| ASTM F 2415 : 2014 | Standard Practice for Continued Airworthiness System for Light Sport Gyroplane Aircraft (Withdrawn 2023) |
| ASTM F 3060 : 2016 : REV A | Standard Terminology for Aircraft |
| ASTM F 2339 : 2019 : REV A | Standard Practice for Design and Manufacture of Reciprocating Spark Ignition Engines for Light Sport Aircraft |
| ASTM F 2972 : 2014 : EDT 1 | Standard Specification for Light Sport Aircraft Manufacturer’s Quality Assurance System |
| ASTM F 2339 : 2019 | Standard Practice for Design and Manufacture of Reciprocating Spark Ignition Engines for Light Sport Aircraft |
| ASTM F 2339 : 2004 | Standard Practice for Design and Manufacture of Reciprocating Spark Ignition Engines for Light Sport Aircraft |
| ASTM F 2483 : 2012 | Standard Practice for Maintenance and the Development of Maintenance Manuals for Light Sport Aircraft |
| ASTM F 2972 : 2014 | Standard Specification for Light Sport Aircraft Manufacturer’s Quality Assurance System |
| ASTM F 2483 : 2018 | Standard Practice for Maintenance and the Development of Maintenance Manuals for Light Sport Aircraft |
| ASTM F 2972 : 2015 | Standard Specification for Light Sport Aircraft Manufacturer’s Quality Assurance System (Withdrawn 2024) |
| ASTM F 2339 : 2017 | Standard Practice for Design and Manufacture of Reciprocating Spark Ignition Engines for Light Sport Aircraft |
| ASTM F 2972 : 2012 | Standard Specification for Light Sport Aircraft Manufacturer’s Quality Assurance System |
| ASTM F 2483 : 2018 : EDT 1 | Standard Practice for Maintenance and the Development of Maintenance Manuals for Light Sport Aircraft |
| ASTM F 2483 : 2005 | Standard Practice for Maintenance and the Development of Maintenance Manuals for Light Sport Aircraft |
| ASTM F 2339 : 2006 : R2009 | Standard Practice for Design and Manufacture of Reciprocating Spark Ignition Engines for Light Sport Aircraft |
| ASTM F 2339 : 2005 | Standard Practice for Design and Manufacture of Reciprocating Spark Ignition Engines for Light Sport Aircraft |
| ASTM F 2339 : 2006 | Standard Practice for Design and Manufacture of Reciprocating Spark Ignition Engines for Light Sport Aircraft |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.