ASTM F 2332 : 2006 : R2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Annular Ball Bearings for Instruments and Precision Rotating Components
Hardcopy , PDF
23-08-2022
English
18-10-2013
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 01.09, 2018 Provides annular ball bearings intended primarily for use in instrument and precision rotating components.
| Committee |
F 34
|
| DocumentType |
Standard
|
| Pages |
145
|
| ProductNote |
Reconfirmed 2013
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers annular ball bearings intended primarily for use in instrument and precision rotating components. Instrument and precision ball bearings should meet tolerances specified in ABMA Standard 12.2, Instrument Ball Bearings Inch Design for Classes ABEC 5P and 7P.
1.2Intended Use—Ball bearings defined by this specification are intended for use in critical components of instrument systems. Such components range from air circulating blowers and drive motors through precision gear trains, gyro gimbals, and pickoffs to rate integrating spin-motors.
1.3The specification contains many of the requirements of MIL-B-81793, which was originally developed by the Department of Defense and maintained by the Naval Air Systems Command (Navy-AS) in Lakehurst, NJ. The following government activity codes may be found in the Department of Defense, Standardization Directory SD-1.2
| Preparing activity | Custodians | Review activities |
| Navy - AS | Army - AT | Army-AV |
| Navy - AS | Navy - MC, SH | |
| Air Force - 99 | Air Force–84 | |
| DLA - GS |
1.4Classification—Annular ball bearings for instrument and precision rotating components shall be of the following types, as specified:
1.4.1Type I—Annular ball bearing, for instruments and precision rotating components, deep groove, unflanged; (See Annex A1 – Annex A4)
1.4.2Type II—Annular ball bearing, for instruments and precision rotating components, deep groove, flanged; (See Annex A5 – Annex A8)
1.4.3Type III—Annular ball bearing, for instruments and precision rotating components, deep groove, unflanged, inner ring extended; (See Annex A9 – Annex A12)
1.4.4Type IV—Annular ball bearing, for instruments and precision rotating components, deep groove, flanged, inner ring extended; (See Annex A13 – Annex A16)
1.4.5Type V—Annular ball bearing, for instruments and precision rotating components, angular contact, unflanged, nonseparable, and counterbored outer ring; (See Annex A17 – Annex A20)
1.4.6Type VI—Annular ball bearing, for instruments and precision rotating components, angular contact, flanged, nonseparable, and counterbored outer ring on flange side; (See Annex A21 – Annex A24)
1.4.7Type VII—Annular ball bearing, for instruments and precision rotating components, angular contact, unflanged, separable, and stepped inner ring; (See Annex A25 – Annex A28)
1.4.8Type VIII—Annular ball bearing, for instruments and precision rotating components, angular contact, flanged, separable, and stepped inner ring; (See Annex A29 – Annex A32)
1.4.9Type IX—Annular ball bearing, for instruments and precision rotating components, angular contact, unflanged, nonseparable, and stepped inner ring. (See Annex A33 – Annex A36)
1.5Inch-Pound Specification—This specification covers only the inch-pound bearings.
1.5.1The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
| ISO 3290:2001 | Rolling bearings Balls Dimensions and tolerances |
| ASTM D 2273 : 1997 : R2002 : EDT 1 | Standard Test Method for Trace Sediment in Lubricating Oils |
| MIL-DTL-197 Revision M:2016 | PACKAGING OF BEARINGS, ASSOCIATED PARTS AND SUBASSEMBLIES |
| MIL-STD-129 Revision R:2014 | Military Marking for Shipment and Storage |
| MIL-STD-130 Revision N:2007 | IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY |
| MIL-G-81937 Revision A:1984 | GREASE, INSTRUMENT, ULTRA CLEAN, METRIC |
| ASTM A 240/A240M : 2011 | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
| MIL-S-81087 Revision C:1981 | SILICONE FLUID, CHLORINATED PHENYL METHYL POLYSILOXANE, NATO CODE NUMBER H-536 |
| MIL-STD-1647 Revision E:2003 | IDENTIFICATION MARKINGS FOR DOMESTICALLY MANUFACTURED BEARINGS, BALL, ANNULAR FOR INSTRUMENTS AND PRECISION COMPONENTS |
| ASTM D 2273 : 1997 : R2002 : EDT 2 | Standard Test Method for Trace Sediment in Lubricating Oils |
| ASTM E 45 : 1997 : EDT 2 | Standard Test Methods for Determining the Inclusion Content of Steel |
| ISO 14644-2:2015 | Cleanrooms and associated controlled environments Part 2: Monitoring to provide evidence of cleanroom performance related to air cleanliness by particle concentration |
| ASTM D 2273 : 1997 | Standard Test Method for Trace Sediment in Lubricating Oils |
| ASME B89.3.1 : 1972 | MEASUREMENT OF OUT-OF-ROUNDNESS |
| ASTM A 666 : 2015 : REDLINE | Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar |
| ASTM A 240/A240M : 2005 | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
| MIL-STD-206 Revision B:1988 | FRICTION TORQUE TESTING FOR INSTRUMENT BALL BEARINGS PARTS 1 AND 2 |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| MIL-PRF-83261 Revision C:2011 | GREASE, AIRCRAFT, EXTREME PRESSURE, ANTI-WEAR |
| ASTM A 380 : 2006 | Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems |
| ANSI/NCSL Z540 1 : 94(R2002) | CALIBRATION - CALIBRATION LABORATORIES AND MEASURING AND TEST EQUIPMENT - GENERAL REQUIREMENTS |
| ASTM A 240/A240M : 2022 | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
| SAE AMS QQ S 763D : 2013(S2015) | STEEL, CORROSION RESISTANT, BARS, WIRE, SHAPES, AND FORGINGS |
| SAE AMS 5688 : 2012 | STEEL, CORROSION-RESISTANT, WIRE, 18CR - 9.0NI (SAE 30302), SPRING TEMPER |
| SAE AMS 5880 : 2013 | STEEL, CORROSION-RESISTANT, BARS, WIRE, AND FORGINGS, 17CR - 0.52MO (0.95 - 1.20C) (SAE 51440C), FOR BEARING APPLICATIONS |
| MIL-B-81744 Revision A:1973 | BARRIER COATING SOLUTION, LUBRICANT MIGRATION DETERRING |
| SAE AMS 2303 : 2016 | STEEL CLEANLINESS, AIRCRAFT QUALITY, MARTENSITIC CORROSION-RESISTANT STEELS, MAGNETIC PARTICLE INSPECTION PROCEDURE |
| ASTM A 756 : 2017 : R2022 | Standard Specification for Stainless Anti-Friction Bearing Steel |
| ASTM D 2273 : 2008 | Standard Test Method for Trace Sediment in Lubricating Oils |
| ASTM A 756 : 2017 : REDLINE | Standard Specification for Stainless Anti-Friction Bearing Steel |
| MIL-STD-1334 Revision B:1977 | PROCESS FOR BARRIER COATING OF ANTI-FRICTION BEARINGS |
| ISO 14644-1:2015 | Cleanrooms and associated controlled environments Part 1: Classification of air cleanliness by particle concentration |
| MIL-PRF-6085 Revision E:2011 | LUBRICATING OIL, INSTRUMENT, AIRCRAFT, LOW VOLATILITY |
| ASTM A 756 : 2017 | Standard Specification for Stainless Anti-Friction Bearing Steel |
| ASTM A 240/A240M : 2020 : REV A | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
| ASTM A 580/A580M : 2018 | Standard Specification for Stainless Steel Wire |
| ASTM D 2273 : 2008 : R2012 | Standard Test Method for Trace Sediment in Lubricating Oils |
| ASTM A 756 : 1994 | Standard Specification for Stainless Anti-Friction Bearing Steel |
| ASTM D 2273 : 2005 | Standard Test Method for Trace Sediment in Lubricating Oils |
| MIL-DTL-53131 Revision A:1998 | LUBRICATING OIL, PRECISION ROLLING ELEMENT BEARING, POLYALPHAOLEFIN BASED |
| FED-STD-791 Revision D:2007 | TESTING METHOD OF LUBRICANTS, LIQUID FUELS, AND RELATED PRODUCTS |
| ISO 10012-1:1992 | Quality assurance requirements for measuring equipment Part 1: Metrological confirmation system for measuring equipment |
| SAE AMS 6444 : 2015 | STEEL, BARS, FORGINGS, AND TUBING, 1.45CR (0.93 - 1.05C) (SAE 52100), PREMIUM AIRCRAFT-QUALITY, CONSUMABLE ELECTRODE VACUUM REMELTED |
| ISO 1224:1984 | Rolling bearings Instrument precision bearings |
| ASTM D 2273 : 2008 : R2016 | Standard Test Method for Trace Sediment in Lubricating Oils (Withdrawn 2023) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.