ASTM E 999 : 2015 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Guide for Controlling the Quality of Industrial Radiographic Film Processing
05-08-2020
English
01-06-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 03.03, 2017 Identifies guidelines which can be used in maintenance and control of industrial radiographic film processing materials and equipment.
| Committee |
E 07
|
| DocumentType |
Redline
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This guide2 establishes guidelines that may be used for the control and maintenance of industrial radiographic film processing equipment and materials. Effective use of these guidelines aid in controlling the consistency and quality of industrial radiographic film processing.
1.2Use of this guide is limited to the processing of films for industrial radiography. This guide includes procedures for wet-chemical processes and dry processing techniques.
1.3The necessity of applying specific control procedures such as those described in this guide is dependent, to a certain extent, on the degree to which a facility adheres to good processing practices as a matter of routine procedure.
1.4If a nondestructive testing agency as described in Practice E543 is used to perform the examination, the testing agency shall meet the requirements of Practice E543.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of federal and local codes prior to use.
| ASTM E 1735 : 2007 : R2014 | Standard Test Method for Determining Relative Image Quality of Industrial Radiographic Film Exposed to X-Radiation from 4 to 25 MeV |
| ASTM E 1030/E1030M : 2015 : REDLINE | Standard Practice for Radiographic Examination of Metallic Castings |
| ASTM E 1030 : 2005 | Standard Test Method for Radiographic Examination of Metallic Castings |
| ASTM E 592 : 2015 : REDLINE | Standard Guide to Obtainable ASTM Equivalent Penetrameter Sensitivity for Radiography of Steel Plates <fraction><num>1</num><den>4 </den></fraction> to 2 in. (6 to 51 mm) Thick with X-Rays and 1 to 6 in. (25 to 152 mm) Thick with <brk/>Cobalt-60 |
| API TR 17TR8 : 2018 | HIGH-PRESSURE HIGH-TEMPERATURE DESIGN GUIDELINES |
| ASTM E 1030 : 2005 : R2011 | Standard Test Method for Radiographic Examination of Metallic Castings |
| ASTM C 1175 : 1999 : REV A : R2004 | Standard Guide to Test Methods and Standards for Nondestructive Testing of Advanced Ceramics |
| ASTM E 543 : 2015 : REDLINE | Standard Specification for Agencies Performing Nondestructive Testing |
| ASTM C 1175 : 1999 : REV A : R2010 | Standard Guide to Test Methods and Standards for Nondestructive Testing of Advanced Ceramics (Withdrawn 2018) |
| ASTM E 1114 : 2009 : EDT 1 | Standard Test Method for Determining the Size of Iridium-192 Industrial Radiographic Sources |
| ASTM E 1742/E1742M : 2018 : REDLINE | Standard Practice for Radiographic Examination |
| ASTM E 94 : 2004 | Standard Guide for Radiographic Examination |
| ASTM E 1161 : 2009 : R2014 | Standard Practice for Radiologic Examination of Semiconductors and Electronic Components |
| 18/30338016 DC | BS ISO 20890-6. In-service inspections for primary coolant circuit components of light water reactors Part 6. Radiographic testing |
| ASTM E 1114 : 2009 : R2014 | Standard Test Method for Determining the Size of Iridium-192 Industrial Radiographic Sources |
| ASTM E 1735 : 2007 | Standard Test Method for Determining Relative Image Quality of Industrial Radiographic Film Exposed to X-Radiation from 4 to 25 MeV |
| ASTM E 1114:2009 | Standard Test Method for Determining the Size of Iridium-192 Industrial Radiographic Sources |
| ASTM E 746 : 2018 : REDLINE | Standard Practice for Determining Relative Image Quality Response of Industrial Radiographic Imaging Systems |
| ABS 0014 : 2018 | GUIDE FOR NONDESTRUCTIVE INSPECTION OF HULL WELDS |
| ASTM E 2104 : 2015 : REDLINE | Standard Practice for Radiographic Examination of Advanced Aero and Turbine Materials and Components |
| ASTM E 94/E94M : 2017 : REDLINE | Standard Guide for Radiographic Examination Using Industrial Radiographic Film |
| ASTM E 94 : 2004 : R2010 | Standard Guide for Radiographic Examination |
| ASTM E 1161 : 2009 | Standard Practice for Radiologic Examination of Semiconductors and Electronic Components |
| ASTM C 1175 : 1999 : REV A | Standard Guide to Test Methods and Standards for Nondestructive Testing of Advanced Ceramics |
| ASTM E 1254 : 2013 | Standard Guide for Storage of Radiographs and Unexposed Industrial Radiographic Films |
| ISO 18917:1999 | Photography Determination of residual thiosulfate and other related chemicals in processed photographic materials Methods using iodine-amylose, methylene blue and silver sulfide |
| ASTM E 543 : 2015 : REDLINE | Standard Specification for Agencies Performing Nondestructive Testing |
| ASTM E 1079 : 2016 : REDLINE | Standard Practice for Calibration of Transmission Densitometers |
| ISO 11699-2:1998 | Non-destructive testing Industrial radiographic films Part 2: Control of film processing by means of reference values |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.