ASTM E 2925 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Manufactured Polymeric Drainage and Ventilation Materials Used to Provide a Rainscreen Function
Hardcopy , PDF
26-08-2019
English
01-06-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
E 06
|
| DocumentType |
Standard
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification is applicable to manufactured polymeric materials used to provide a rainscreen function, a means for the drainage of liquid moisture and the ventilation of vapor moisture that enters an above-grade exterior wall assembly. Rainscreen materials that comply with this specification are intended to be used behind exterior cladding products and intended to cover one hundred percent (100 %) of the wall area that is designed to provide a rainscreen function to resist water infiltration.
1.2This specification addresses the following types of rainscreen materials:
1.2.1Type A—entangled mesh materials.
1.2.2Type B—formed/textured sheet material.
1.2.3Type C—formed battens.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 5322 : 1998 | Standard Practice for Immersion Procedures for Evaluating the Chemical Resistance of Geosynthetics to Liquids |
| ASTM D 5199 : 2012 : R2019 | Standard Test Method for Measuring the Nominal Thickness of Geosynthetics |
| ASTM D 6108 : 2019 | Standard Test Method for Compressive Properties of Plastic Lumber and Shapes |
| ASTM D 6108 : 2003 | Standard Test Method for Compressive Properties of Plastic Lumber and Shapes |
| ASTM C 1338 : 2000 | Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings |
| ASTM D 5199 : 2001 | Standard Test Method for Measuring the Nominal Thickness of Geosynthetics |
| ASTM C 1338 : 2014 | Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings |
| ASTM D 3045 : 1992 : R1997 | Standard Practice for Heat Aging of Plastics Without Load |
| ASTM D 3045 : 2018 | Standard Practice for Heat Aging of Plastics Without Load |
| ASTM E 2273 : 2018 | Standard Test Method for Determining the Drainage Efficiency of Exterior Insulation and Finish Systems (EIFS) Clad Wall Assemblies |
| ASTM C 1338 : 2019 | Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings |
| ASTM C 1338 : 2008 | Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings |
| ASTM D 6364 : 2006 | Standard Test Method for Determining Short-Term Compression Behavior of Geosynthetics |
| ASTM D 5322 : 1998 : R2009 | Standard Practice for Immersion Procedures for Evaluating the Chemical Resistance of Geosynthetics to Liquids |
| ASTM D 6364 : 2006 : R2018 | Standard Test Method for Determining Short-Term Compression Behavior of Geosynthetics |
| ASTM D 6364 : 2006 : R2011 | Standard Test Method for Determining Short-Term Compression Behavior of Geosynthetics |
| ASTM D 6108 : 1997 | Standard Test Method for Compressive Properties of Plastic Lumber and Shapes |
| ASTM E 2273 : 2003 : R2011 | Standard Test Method for Determining the Drainage Efficiency of Exterior Insulation and Finish Systems (EIFS) Clad Wall Assemblies |
| ASTM D 5199 : 2012 | Standard Test Method for Measuring the Nominal Thickness of Geosynthetics |
| ASTM D 5199 : 2011 | Standard Test Method for Measuring the Nominal Thickness of Geosynthetics |
| ASTM D 5322 : 1998 : R2003 | Standard Practice for Immersion Procedures for Evaluating the Chemical Resistance of Geosynthetics to Liquids |
| ASTM D 5322 : 2017 | Standard Practice for Laboratory Immersion Procedures for Evaluating the Chemical Resistance of Geosynthetics to Liquids |
| ASTM D 6108 : 2018 | Standard Test Method for Compressive Properties of Plastic Lumber and Shapes |
| ASTM D 6108 : 2013 | Standard Test Method for Compressive Properties of Plastic Lumber and Shapes |
| ASTM D 5199 : 2001 : R2006 | Standard Test Method for Measuring the Nominal Thickness of Geosynthetics |
| ASTM D 6108 : 2009 | Standard Test Method for Compressive Properties of Plastic Lumber and Shapes |
| ASTM D 6364 : 1999 | Standard Test Method for Determining the Short-Term Compression Behavior of Geosynthetics |
| ASTM E 2273 : 2003 | Standard Test Method for Determining the Drainage Efficiency of Exterior Insulation and Finish Systems (EIFS) Clad Wall Assemblies |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.