ASTM E 2597/E2597M : 2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Manufacturing Characterization of Digital Detector Arrays
Hardcopy , PDF
01-03-2022
English
25-02-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.This practice describes the evaluation of Digital Detector Arrays (DDAs), and assures that one common standard exists for quantitative comparison of DDAs so that an appropriate DDA is selected to meet NDT requirements.
| Committee |
E 07
|
| DocumentType |
Standard Practice
|
| Pages |
19
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice describes the evaluation of Digital Detector Arrays (DDAs), and assures that one common standard exists for quantitative comparison of DDAs so that an appropriate DDA is selected to meet NDT requirements.
1.2This practice is intended for use by manufacturers or integrators of DDAs to provide quantitative results of DDA characteristics for NDT user or purchaser consumption. Some of these tests require specialized test phantoms to assure consistency among results among suppliers or manufacturers. These tests are not intended for users to complete, nor are they intended for long term stability tracking and lifetime measurements. However, they may be used for this purpose, if so desired.
1.3The results reported based on this standard should be based on a group of at least three individual detectors for a particular model number.
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM E 1161 : 2021 | Standard Practice for Radiographic Examination of Semiconductors and Electronic Components |
| ASTM E 2698 : 2018 : EDT 1 | Standard Practice for Radiographic Examination Using Digital Detector Arrays |
| ASTM E 2903 : 2018 | Standard Test Method for Measurement of the Effective Focal Spot Size of Mini and Micro Focus X-ray Tubes |
| ASTM E 543 : 2021 | Standard Specification for Agencies Performing Nondestructive Testing |
| ASTM E 2533 : 2021 | Standard Guide for Nondestructive Examination of Polymer Matrix Composites Used in Aerospace Applications |
| ASTM E 2737 : 2010 : R2018 | Standard Practice for Digital Detector Array Performance Evaluation and Long-Term Stability |
| ASTM E 2982 : 2021 | Standard Guide for Nondestructive Examination of Thin-Walled Metallic Liners in Filament-Wound Pressure Vessels Used in Aerospace Applications |
| ASTM E 2446 : 2016 | Standard Practice for Manufacturing Characterization of Computed Radiography Systems |
| ASTM E 1316 : 2011 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2015 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2009 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2008 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2010 : REV C | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2020 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2017 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2013 : REV C | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2000 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1815 : 1996 | Standard Test Method for Classification of Film Systems for Industrial Radiography |
| ASTM E 1316 : 2019 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2014 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2013 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1815 : 2018 | Standard Test Method for Classification of Film Systems for Industrial Radiography |
| ASTM E 1316 : 2018 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2011 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2007 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2015 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2019 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2021 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2013 : REV D | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2000 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2019 | Standard Terminology for Nondestructive Examinations |
| ASTM E 2002 : 1998 | Standard Practice for Determining Total Image Unsharpness in Radiology |
| ASTM E 2446 : 2005 : R2010 | Standard Practice for Classification of Computed Radiology Systems |
| ASTM E 1316 : 2001 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2003 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2018 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2006 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2016 | Standard Terminology for Nondestructive Examinations |
| ASTM E 2002 : 1998 : R2003 : EDT 1 | Standard Practice for Determining Total Image Unsharpness in Radiology |
| ASTM E 1815 : 2008 : R2013 : EDT 1 | Standard Test Method for Classification of Film Systems for Industrial Radiography |
| ASTM E 2002 : 1998 : R2009 | Standard Practice for Determining Total Image Unsharpness in Radiology |
| ASTM E 1316 : 2021 : REV D | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2002 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2014 : EDT 1 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2010 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2013 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2021 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 2446 : 2005 | Standard Practice for Classification of Computed Radiology Systems |
| ASTM E 1316 : 2017 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2016 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1815 : 2008 | Standard Test Method for Classification of Film Systems for Industrial Radiography |
| ASTM E 2445 : 2005 : R2010 | Standard Practice for Qualification and Long-Term Stability of Computed Radiology Systems |
| ASTM E 1316 : 2009 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2002 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2004 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2007 : REV C | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2010 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2013 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1815 : 2006 | Standard Test Method for Classification of Film Systems for Industrial Radiography |
| ASTM E 2002 : 2015 | Standard Practice for Determining Total Image Unsharpness and Basic Spatial Resolution in Radiography and Radioscopy |
| ASTM E 1316 : 2021 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2007 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2005 | Standard Terminology for Nondestructive Testing |
| ASTM E 1316 : 2004 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2021 : REV C | Standard Terminology for Nondestructive Examinations |
| ASTM E 2445 : 2005 | Standard Practice for Qualification and Long-Term Stability of Computed Radiology Systems |
| ASTM E 2446 : 2015 | Standard Practice for Manufacturing Characterization of Computed Radiography Systems |
| ASTM E 1316 : 2007 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2012 | Standard Terminology for Nondestructive Examinations |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.