ASTM E 2375 : 2022
Current
The latest, up-to-date edition.
Standard Practice for Ultrasonic Testing of Wrought Products
Hardcopy , PDF
English
11-01-2023
Committee |
E 07
|
DocumentType |
Standard Practice
|
Pages |
23
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1Purpose—This practice establishes the minimum requirements for ultrasonic examination of wrought products.
Note 1:This practice was adopted to replace MIL-STD-2154, 30 Sept. 1982. This practice is intended to be used for the same applications as the document which it replaced. Users should carefully review its requirements when considering its use for new, or different applications, or both.
1.2Application—This practice is applicable for examination of materials such as, wrought metals and wrought metal products having a thickness or cross section equal to 0.250 in. (6.35 mm) or greater.
1.2.1Wrought Aluminum Alloy Products—Examination shall be in accordance with Practice B594. Angle beam scans of wrought aluminum alloy products shall be performed in accordance with this practice as agreed upon by the purchaser and supplier.
1.3Acceptance Class—When examination is performed in accordance with this practice, engineering drawings, specifications, or other applicable documents shall indicate the acceptance criteria. Five ultrasonic acceptance classes are defined in Table 1. One or more of these classes may be used to establish the acceptance criteria or additional or alternate criteria may be specified.
1.4Order of Precedence—Contractual requirements and authorized direction from the cognizant engineering organization may add to or modify the requirements of this practice. Otherwise, in the event of conflict between the text of this practice and the references cited herein, the text of this practice takes precedence. Nothing in this practice, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.
1.5Measurement Values—The values stated in inch-pounds are to be regarded as standard. The metric equivalents are in parentheses.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM E 2982 : 2021 | Standard Guide for Nondestructive Examination of Thin-Walled Metallic Liners in Filament-Wound Pressure Vessels Used in Aerospace Applications |
ASTM E 543 : 2021 | Standard Specification for Agencies Performing Nondestructive Testing |
ASTM E 3370 : 2022 | Standard Practice for Matrix Array Ultrasonic Testing of Composites, Sandwich Core Constructions, and Metals Used in Aerospace Applications |
ASTM E 127 : 2020 | Standard Practice for Fabrication and Control of Flat Bottomed Hole Ultrasonic Standard Reference Blocks |
ASTM E 2981 : 2021 | Standard Guide for Nondestructive Examination of Composite Overwraps in Filament Wound Pressure Vessels Used in Aerospace Applications |
ASTM F 3268 : 2018 : REV A | Standard Guide for <emph type="bdit">in vitro</emph> Degradation Testing of Absorbable Metals |
NASA-STD-5009C:2023 | Nondestructive Evaluation Requirements for Fracture Critical Metallic Components |
ASTM E 1316 : 2022 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2024 : REV B | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2024 | Standard Terminology for <?Pub Dtl?>Nondestructive Examinations |
ASTM E 1316 : 2023 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2024 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2023 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2023 : REV B | Standard Terminology for Nondestructive Examinations |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.