ASTM E 2261/E2261M : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Examination of Welds Using the Alternating Current Field Measurement Technique
Hardcopy , PDF
05-01-2022
English
06-07-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.This practice describes procedures to be followed during alternating current field measurement examination of welds for baseline and service-induced surface breaking discontinuities.
| Committee |
E 07
|
| DocumentType |
Standard Practice
|
| Pages |
15
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice describes procedures to be followed during alternating current field measurement examination of welds for baseline and service-induced surface breaking discontinuities.
1.2This practice is intended for use on welds in any metallic material.
1.3This practice does not establish weld acceptance criteria.
1.4Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system might not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 2982 : 2021 | Standard Guide for Nondestructive Examination of Thin-Walled Metallic Liners in Filament-Wound Pressure Vessels Used in Aerospace Applications |
| ASTM E 1316 : 2011 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2015 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2009 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2008 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2010 : REV C | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2020 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2017 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2013 : REV C | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2000 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 543 : 2021 | Standard Specification for Agencies Performing Nondestructive Testing |
| ASTM E 1316 : 2019 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2014 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2013 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2018 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2011 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2007 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2015 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2019 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2021 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2013 : REV D | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2000 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2019 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2001 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2003 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2018 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2006 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 543 : 2015 | Standard Specification for Agencies Performing Nondestructive Testing |
| ASTM E 1316 : 2016 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2002 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2014 : EDT 1 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2010 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2013 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2021 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2017 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2016 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2009 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2002 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2004 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2007 : REV C | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2010 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2013 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2021 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2007 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2005 | Standard Terminology for Nondestructive Testing |
| ASTM E 1316 : 2004 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2021 : REV C | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2007 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2012 | Standard Terminology for Nondestructive Examinations |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.