ASTM E 2251 : 2003
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
Available format(s)
Hardcopy , PDF
Superseded date
30-09-2020
Language(s)
English
Published date
10-01-2003
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
E 20
|
| DocumentType |
Standard
|
| Pages |
18
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
1.1 The purpose of this standard is to specify liquid-in-glass ASTM thermometers using low hazard thermometric liquids defined in this standard.
1.2 This standard specifies liquid-in-glass thermometers graduated in degrees Celsius or degrees Fahrenheit that are frequently identified and used in methods under the jurisdiction of the various technical committees within ASTM. The current approved thermometers are listed in Table 1.
1.3 The technical requirements for the thermometric liquids used in the thermometers in are specified in . Tests for conformity to the technical requirements are also found in Annex A1.
Note 1—It has been found by experience that ASTM Thermometers, although developed in general for specific tests, may also be found suitable for other applications, thus precluding the need for new thermometer specifications differing in only minor features. However, it is suggested that technical committees contact E20.05 before choosing a currently designated thermometer for a new method to be sure the thermometer will be suitable for the intended application.
1.4 For full rationale, see Appendix X1.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
| ASTM D 1601 : 2018 | Standard Test Method for Dilute Solution Viscosity of Ethylene Polymers |
| ASTM D 4603 : 2018 | Standard Test Method for Determining Inherent Viscosity of Poly(Ethylene Terephthalate) (PET) by Glass Capillary Viscometer |
| ASTM D 4943 : 2018 | Standard Test Method for Shrinkage Factors of Cohesive Soils by the Water Submersion Method |
| ASTM C 782 : 2013 : R2018 | Standard Test Method for Softness of Preformed Tape Sealants |
| ASTM D 2111 : 2010 : R2015 | Standard Test Methods for Specific Gravity and Density of Halogenated Organic Solvents and Their Admixtures |
| ASTM D 2251 : 2010 : R2015 | Standard Test Method for Metal Corrosion by Halogenated Organic Solvents and Their Admixtures |
| ASTM D 3195/D3195M : 2010 : R2015 | Standard Practice for Rotameter Calibration |
| ASTM D 5006 : 2011 : R2016 | Standard Test Method for Measurement of Fuel System Icing Inhibitors (Ether Type) in Aviation Fuels |
| ASTM D 7577 : 2012 : R2016 | Standard Test Method for Determining the Accelerated Iron Corrosion Rating of Denatured Fuel Ethanol and Ethanol Fuel Blends |
| ASTM F 483 : 2009 : R2014 | Standard Practice for Total Immersion Corrosion Test for Aircraft Maintenance Chemicals |
| ASTM D 1321 : 2016 : REV A | Standard Test Method for Needle Penetration of Petroleum Waxes |
| ASTM D 1525 : 2017 : EDT 1 | Standard Test Method for Vicat Softening Temperature of Plastics |
| ASTM D 2158 : 2016 : REV A : EDT 1 | Standard Test Method for Residues in Liquefied Petroleum (LP) Gases |
| ASTM D 2500 : 2017 : REV A | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels |
| ASTM D 323 : 2015 : REV A | Standard Test Method for Vapor Pressure of Petroleum Products (Reid Method) |
| ASTM D 4171 : 2016 : REV A | Standard Specification for Fuel System Icing Inhibitors |
| ASTM D 5853 : 2017 : REV A | Standard Test Method for Pour Point of Crude Oils |
| ASTM D 6371 : 2017 : REV A | Standard Test Method for Cold Filter Plugging Point of Diesel and Heating Fuels |
| ASTM D 6572 : 2013 : EDT 2 | Standard Test Methods for Determining Dispersive Characteristics of Clayey Soils by the Crumb Test |
| ASTM E 77 : 2014 : EDT 1 | Standard Test Method for Inspection and Verification of Thermometers |
| ASTM D 2726/D2726M : 2019 | Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Asphalt Mixtures |
| ASTM F 2105 : 2018 | Standard Test Method for Measuring Air Performance Characteristics of Vacuum Cleaner Motor/Fan Systems |
| ASTM C 359 : 2018 | Standard Test Method for Early Stiffening of Hydraulic Cement (Mortar Method) |
| ASTM D 2746/D2746M : 2018 | Standard Test Method for Staining Tendency of Asphalt (Stain Index) |
| ASTM C 1810/C1810M : 2019 | Standard Guide for Comparing Performance of Concrete-Making Materials Using Mortar Mixtures |
| ASTM D 3012 : 2019 | Standard Test Method for Thermal-Oxidative Stability of Polypropylene Using a Specimen Rotator Within an Oven |
| ASTM E 126 : 2019 | Standard Test Method for Inspection, Calibration, and Verification of ASTM Hydrometers |
| ASTM D 5/D5M : 2019 | Standard Test Method for Penetration of Bituminous Materials |
| ASTM E 100 : 2019 | Standard Specification for ASTM Hydrometers |
| ASTM G 42 : 2011 : R2019 : EDT 1 | Standard Test Method for Cathodic Disbonding of Pipeline Coatings Subjected to Elevated Temperatures |
| ASTM F 1914 : 2018 | Standard Test Methods for Short-Term Indentation and Residual Indentation of Resilient Floor Covering |
| ASTM F 558 : 2018 | Standard Test Method for Measuring Air Performance Characteristics of Vacuum Cleaners |
| ASTM F 820 : 2018 | Standard Test Method for Measuring Air Performance Characteristics of Central Vacuum Cleaning Systems |
| ASTM D 4659 : 2019 | Standard Test Methods for Polyurethane Raw Materials: Determination of Specific Gravity of Isocyanates |
| ASTM D 8164 : 2019 | Standard Guide for Digital Contact Thermometers for Petroleum Products, Liquid Fuels, and Lubricant Testing |
| ASTM D 5478 : 2013 : R2018 | Standard Test Methods for Viscosity of Materials by a Falling Needle Viscometer |
| ASTM D 6084/D6084M : 2018 | Standard Test Method for Elastic Recovery of Asphalt Materials by Ductilometer |
| ASTM D 4669 : 2018 | Standard Test Method for Polyurethane Raw Materials: Determination of Specific Gravity of Polyols |
| ASTM D 7263 : 2009 : R2018 : EDT 2 | Standard Test Methods for Laboratory Determination of Density (Unit Weight) of Soil Specimens |
| ASTM D 2838 : 2018 | Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting |
| ASTM D 1045 : 2014 | Standard Test Methods for Sampling and Testing Plasticizers Used in Plastics |
| ASTM D 1074 : 2017 | Standard Test Method for Compressive Strength of Asphalt Mixtures |
| ASTM D 1125 : 2014 | Standard Test Methods for Electrical Conductivity and Resistivity of Water (Withdrawn 2023) |
| ASTM D 1243 : 2015 | Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride Polymers |
| ASTM D 1310 : 2014 | Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus |
| ASTM D 1429 : 2013 | Standard Test Methods for Specific Gravity of Water and Brine (Withdrawn 2022) |
| ASTM D 1608 : 2016 | Standard Test Method for Oxides of Nitrogen in Gaseous Combustion Products (Phenol-Disulfonic Acid Procedures) (Withdrawn 2023) |
| ASTM D 1755 : 2015 | Standard Specification for Poly(Vinyl Chloride) Resins |
| ASTM D 1795 : 2013 | Standard Test Method for Intrinsic Viscosity of Cellulose |
| ASTM C 403/C403M : 2016 | Standard Test Method for Time of Setting of Concrete Mixtures by Penetration Resistance |
| ASTM D 2732 : 2014 | Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film<brk/> and Sheeting |
| ASTM D 2913 : 2014 | Standard Test Method for Mercaptan Content of the Atmosphere |
| ASTM D 2914 : 2015 | Standard Test Methods for Sulfur Dioxide Content of the Atmosphere (West-Gaeke Method) |
| ASTM D 3082 : 2015 | Standard Test Method for Boron in Water (Withdrawn 2024) |
| ASTM D 3154 : 2014 | Standard Test Method for Average Velocity in a Duct (Pitot Tube Method) |
| ASTM D 3685/D3685M : 2013 | Standard Test Methods for Sampling and Determination of Particulate Matter in Stack Gases |
| ASTM D 3591 : 2017 | Standard Test Method for Determining Logarithmic Viscosity Number of Poly(Vinyl Chloride) (PVC) in Formulated Compounds |
| ASTM D 3603 : 2014 | Standard Test Method for Rust-Preventing Characteristics of Steam Turbine Oil in the Presence of Water (Horizontal Disk Method) |
| ASTM D 3642 : 2013 | Standard Test Method for Softening Point of Certain Alkali-Soluble Resins |
| ASTM D 3934 : 2014 | Standard Test Method for Flash/No Flash Test—Equilibrium Method by a Closed-Cup Apparatus |
| ASTM D 3941 : 2014 | Standard Test Method for Flash Point by the Equilibrium Method With a Closed-Cup Apparatus |
| ASTM D 4130 : 2015 | Standard Test Method for Sulfate Ion in Brackish Water, Seawater, and Brines (Withdrawn 2024) |
| ASTM D 4350 : 2016 | Standard Test Method for Corrosivity Index of Plastics and Fillers |
| ASTM D 4532 : 2015 | Standard Test Method for Respirable Dust in Workplace Atmospheres Using Cyclone Samplers |
| ASTM D 4539 : 2017 | Standard Test Method for Filterability of Diesel Fuels by Low-Temperature Flow Test (LTFT) |
| ASTM D 4878 : 2015 | Standard Test Methods for Polyurethane Raw Materials: Determination of Viscosity of Polyols |
| ASTM D 4889 : 2015 | Standard Test Methods for Polyurethane Raw Materials: Determination of Viscosity of Crude or Modified Isocyanates |
| ASTM D 4957 : 2018 | Standard Test Method for Apparent Viscosity of Asphalt Emulsion Residues and Non-Newtonian Asphalts by Vacuum Capillary Viscometer |
| ASTM D 5015 : 2015 | Standard Test Method for pH of Atmospheric Wet Deposition Samples by Electrometric Determination |
| ASTM D 113 : 2017 | Standard Test Method for Ductility of Asphalt Materials |
| ASTM D 5298 : 2016 | Standard Test Method for Measurement of Soil Potential (Suction) Using Filter Paper |
| ASTM D 5346 : 2017 | Standard Test Method for Determination of the Pour Point of Petroleum Oil Used in Fatliquors and Softening Compounds |
| ASTM D 5438 : 2017 | Standard Practice for Collection of Floor Dust for Chemical Analysis |
| ASTM D 5440 : 2017 | Standard Test Method for Determining the Melting Point of Fats and Oils |
| ASTM D 721 : 2017 | Standard Test Method for Oil Content of Petroleum Waxes |
| ASTM D 5801 : 2017 | Standard Test Method for Toughness and Tenacity of Asphalt Materials |
| ASTM D 914 : 2012 | Standard Test Methods for Ethylcellulose |
| ASTM D 972 : 2016 | Standard Test Method for Evaporation Loss of Lubricating Greases and Oils |
| ASTM D 6209 : 2013 | Standard Test Method for Determination of Gaseous and Particulate Polycyclic Aromatic Hydrocarbons in Ambient Air (Collection on Sorbent-Backed Filters with Gas Chromatographic/Mass Spectrometric Analysis) |
| ASTM E 337 : 2015 | Standard Test Method for Measuring Humidity with a Psychrometer (the Measurement of Wet- and Dry-Bulb Temperatures) |
| ASTM D 6288 : 2017 | Standard Practice for Separation and Washing of Recycled Plastics Prior to Testing |
| ASTM D 6331 : 2016 | Standard Test Method for Determination of Mass Concentration of Particulate Matter from Stationary Sources at Low Concentrations (Manual Gravimetric Method) |
| ASTM D 6539 : 2013 | Standard Test Method for Measurement of the Permeability of Unsaturated Porous Materials by Flowing Air (Withdrawn 2022) |
| ASTM E 644 : 2011 | Standard Test Methods for Testing Industrial Resistance Thermometers |
| ASTM D 61 : 2015 | Standard Test Method for Softening Point of Pitches (Cube-in-Water Method) |
| ASTM D 6784 : 2016 | Standard Test Method for Elemental, Oxidized, Particle-Bound and Total Mercury in Flue Gas Generated from Coal-Fired Stationary Sources (Ontario Hydro Method) |
| ASTM D 6925 : 2015 | Standard Test Method for Preparation and Determination of the Relative Density of Asphalt Mix Specimens by Means of the Superpave Gyratory Compactor |
| ASTM D 6926 : 2016 | Standard Practice for Preparation of Asphalt Mixture Specimens Using Marshall Apparatus |
| ASTM D 6927 : 2015 | Standard Test Method for Marshall Stability and Flow of Asphalt Mixtures |
| ASTM F 390 : 2011 | Standard Test Method for Sheet Resistance of Thin Metallic Films With a Collinear Four-Probe Array (Withdrawn 2020) |
| ASTM D 8055 : 2017 | Standard Guide for Selecting an Appropriate Electronic Thermometer for Replacing Mercury Thermometers in D04 Road and Paving Standards |
| ASTM D 5869/D5869M : 2007 : REV A : R2018 : EDT 1 | Standard Practice for Dark Oven Heat Exposure of Roofing and Waterproofing Materials |
| ASTM D 8175 : 2018 | Standard Test Method for Finite Flash Point Determination of Liquid Wastes by Pensky-Martens Closed Cup Tester |
| ASTM E 1 : 2014 | Standard Specification for ASTM Liquid-in-Glass Thermometers |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.