ASTM E 1820 : 2023 : REV B
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Measurement of Fracture Toughness
Hardcopy , PDF
29-05-2024
English
01-06-2023
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
E 08
|
| DocumentType |
Test Method
|
| Pages |
67
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers procedures and guidelines for the determination of fracture toughness of metallic materials using the following parameters: K, J, and CTOD (δ). Toughness can be measured in the R-curve format or as a point value. The fracture toughness determined in accordance with this test method is for the opening mode (Mode I) of loading.
Note 1:Until this version, KIc could be evaluated using this test method as well as by using Test Method E399. To avoid duplication, the evaluation of KIc has been removed from this test method and the user is referred to Test Method E399.
1.2The recommended specimens are single-edge bend, [SE(B)], compact, [C(T)], and disk-shaped compact, [DC(T)]. All specimens contain notches that are sharpened with fatigue cracks.
1.2.1Specimen dimensional (size) requirements vary according to the fracture toughness analysis applied. The guidelines are established through consideration of material toughness, material flow strength, and the individual qualification requirements of the toughness value per values sought.
Note 2:Other standard methods for the determination of fracture toughness using the parameters K, J, and CTOD are contained in Test Methods E399, E1290, and E1921. This test method was developed to provide a common method for determining all applicable toughness parameters from a single test.
1.3The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 647 : 2023 : REV A | Standard Test Method for Measurement of Fatigue Crack Growth Rates |
| ASTM E 1921 : 2022 : REV A | Standard Test Method for Determination of Reference Temperature, <emph type="bdit">T<inf >0</inf></emph>, for Ferritic Steels in the Transition Range |
| ASTM E 2215 : 2019 | Standard Practice for Evaluation of Surveillance Capsules from Light-Water Moderated Nuclear Power Reactor Vessels |
| ASTM F 3056 : 2014 : R2021 | Standard Specification for Additive Manufacturing Nickel Alloy (UNS N06625) with Powder Bed Fusion |
| ASTM F 3213 : 2017 | Standard for Additive Manufacturing – Finished Part Properties – Standard Specification for Cobalt-28 Chromium-6 Molybdenum via Powder Bed Fusion |
| ASTM A 788/A788M : 2022 : REV A | Standard Specification for Steel Forgings, General Requirements |
| ASTM E 2818 : 2011(R2019) | Standard Practice for Determination of Quasistatic Fracture Toughness of Welds |
| ASTM F 3318 : 2018 | Standard for Additive Manufacturing – Finished Part Properties – Specification for AlSi10Mg with Powder Bed Fusion – Laser Beam |
| ASTM E 1253 : 2021 | Standard Guide for Reconstitution of Charpy-Sized Specimens |
| ASTM E 509/E509M : 2021 | Standard Guide for In-Service Annealing of Light-Water Moderated Nuclear Reactor Vessels |
| ASTM E 399 : 2023 | Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness of Metallic Materials |
| ASTM E 636 : 2020 | Standard Guide for Conducting Supplemental Surveillance Tests for Nuclear Power Reactor Vessels |
| ASTM A 1099/A1099M : 2020 | Standard Specification for Modified Alloy Steel Forgings, Forged Bar, and Rolled Bar Commonly Used in Oil and Gas Pressure Vessels |
| ASTM E 2899 : 2019 : EDT 1 | Standard Test Method for Measurement of Initiation Toughness in Surface Cracks Under Tension and Bending |
| ASTM F 3055 : 2014 : REV A : R2021 | Standard Specification for Additive Manufacturing Nickel Alloy (UNS N07718) with Powder Bed Fusion |
| ASTM F 2924 : 2014 : R2021 | Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium with Powder Bed Fusion |
| ASTM E 1823 : 2023 | Standard Terminology Relating to Fatigue and Fracture Testing |
| ASTM F 3184 : 2016 | Standard Specification for Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion |
| ASTM E 185 : 2021 | Standard Practice for Design of Surveillance Programs for Light-Water Moderated Nuclear Power Reactor Vessels |
| ASTM F 3001 : 2014 : R2021 | Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium ELI (Extra Low Interstitial) with Powder Bed Fusion |
| ASTM F 3122 : 2014 : R2022 | Standard Guide for Evaluating Mechanical Properties of Metal Materials Made via Additive Manufacturing Processes |
| ASTM F 3439 : 2022 | Additive manufacturing of metals — Finished part properties — Orientation and location dependence of mechanical properties for metal powder bed fusion |
| ASTM F 3302 : 2018 | Standard for Additive Manufacturing – Finished Part Properties – Standard Specification for Titanium Alloys via Powder Bed Fusion |
| ASTM E 2472 : 2012 : R2018 : EDT 2 | Standard Test Method for Determination of Resistance to Stable Crack Extension under Low-Constraint Conditions |
| ASTM E 1457 : 2019 : EDT 1 | Standard Test Method for Measurement of Creep Crack Growth Times in Metals |
| SAE AMS6468G | Steel, Welding Wire, 1.0Cr - 10Ni - 3.8Co - 0.45Mo - 0.08V (0.14 - 0.17C), Vacuum Melted, Environment Controlled Packaging |
| ASTM F 3184 : 2016 : R2023 | Standard Specification for Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion |
| ASTM A 788/A788M : 2023 | Standard Specification for Steel Forgings, General Requirements |
| ASTM E 2472 : 2012 : R2018 : EDT 3 | Standard Test Method for Determination of Resistance to Stable Crack Extension under Low-Constraint Conditions |
| ASTM E 1823 : 2024 : REV A | Standard Terminology Relating to Fatigue and Fracture Testing |
| ASTM E 647 : 2023 : REV B | Standard Test Method for Measurement of Fatigue Crack Growth Rates |
| ASTM E 2899 : 2024 | Standard Test Method for Measurement of Initiation Toughness in Surface Cracks Under Tension and Bending |
| ASTM E 531 : 2023 | Standard Practice for Surveillance Testing of High-Temperature Nuclear Component Materials |
| ASTM E 1921 : 2023 : REV B | Standard Test Method for Determination of Reference Temperature, <emph type="bdit">T<inf >0</inf></emph>, for Ferritic Steels in the Transition Range |
| ASTM F 3607 : 2022 | Standard Specification for Additive Manufacturing – Finished Part Properties – Maraging Steel via Powder Bed Fusion |
| ASTM E 1823 : 2024 | Standard Terminology Relating to Fatigue and Fracture Testing |
| ASTM E 8/E8M : 2024 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM E 23 : 2024 | Standard Test Methods for Notched Bar Impact Testing of Metallic Materials |
| ASTM E 1823 : 2024 : REV A | Standard Terminology Relating to Fatigue and Fracture Testing |
| ASTM E 1921 : 2023 : REV B | Standard Test Method for Determination of Reference Temperature, <emph type="bdit">T<inf >0</inf></emph>, for Ferritic Steels in the Transition Range |
| ASTM E 23 : 2023 : REV A | Standard Test Methods for Notched Bar Impact Testing of Metallic Materials |
| ASTM E 8/E8M : 2022 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM E 1921 : 2023 : REV A | Standard Test Method for Determination of Reference Temperature, <emph type="bdit">T<inf >0</inf></emph>, for Ferritic Steels in the Transition Range |
| ASTM E 1921 : 2023 | Standard Test Method for Determination of Reference Temperature, <emph type="bdit">T<inf >0</inf></emph>, for Ferritic Steels in the Transition Range |
| ASTM E 1921 : 2022 : REV A | Standard Test Method for Determination of Reference Temperature, <emph type="bdit">T<inf >0</inf></emph>, for Ferritic Steels in the Transition Range |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.