ASTM E 1537 : 2007
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Fire Testing of Upholstered Furniture
Hardcopy , PDF
11-11-2014
English
01-05-2007
Committee |
E 05
|
DocumentType |
Test Method
|
Pages |
22
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1 This is a fire-test-response standard.
1.2 The purpose of this test method is to determine the burning behavior of upholstered furniture used in public occupancies by measuring specific fire-test responses when the specimen of furniture is subjected to a specified flaming ignition source under well-ventilated conditions.
1.3 Data are obtained describing the burning behavior from a specific ignition source until all burning has ceased, a period of 1 h has elapsed, or flashover appears inevitable.
1.4 This test method does not provide information on the fire performance of upholstered furniture in fire conditions other than those conditions specified. In particular, this test method does not apply to smoldering ignition by cigarettes. See for further information.
1.5 The rate of heat release of the burning specimen is measured by an oxygen consumption method. See for further information.
1.6 The production of light obscuring smoke is measured and the concentrations of certain toxic gas species in the combustion gases are determined. See for further information.
1.7 The burning behavior is visually documented by photographic or video recordings, whenever possible.
1.8 The system of units to be used in referee decisions is the SI system of units, see IEEE/ASTM SI-10 only. The units given in parentheses are for information only.
1.9 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions
1.10 Fire testing of products and materials is inherently hazardous, and adequate safeguards for personnel and property shall be employed in conducting these tests. This test method may involve hazardous materials, operations, and equipment
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM E 603 : 2017 | Standard Guide for Room Fire Experiments |
ASTM E 2280 : 2017 | Standard Guide for Fire Hazard Assessment of the Effect of Upholstered Seating Furniture Within Patient Rooms of Health Care Facilities |
ASTM F 1550 : 2016 | Standard Test Method for Determination of Fire-Test-Response Characteristics of Components or Composites of Mattresses or Furniture for Use in Correctional Facilities after Exposure to Vandalism, by Employing a Bench Scale Oxygen Consumption Calorimeter |
ASTM E 176 : 2018 : REV A | Standard Terminology of Fire Standards |
ASTM D 5537 : 2018 | Standard Test Method for Heat Release, Flame Spread, Smoke Obscuration, and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration |
ASTM E 1822 : 2017 | Standard Test Method for Fire Testing of Stacked Chairs |
ASTM E 1995 : 2018 | Standard Test Method for Measurement of Smoke Obscuration Using a Conical Radiant Source in a Single Closed Chamber, With the Test Specimen Oriented Horizontally |
ASTM E 2574/E2574M : 2017 | Standard Test Method for Fire Testing of School Bus Seat Assemblies |
ASTM E 2067 : 2015 | Standard Practice for Full-Scale Oxygen Consumption Calorimetry Fire Tests |
ASTM E 3020 : 2016 : REV A | Standard Practice for Ignition Sources |
ASTM E 1590 : 2017 | Standard Test Method for Fire Testing of Mattresses |
ASTM F 1870 : 2016 | Standard Guide for Selection of Fire Test Methods for the Assessment of Upholstered Furnishings in Detention and Correctional Facilities |
ASTM E 2335 : 2017 | Standard Guide for Laboratory Monitors |
ASTM E 1591 : 2013 | Standard Guide for Obtaining Data for Fire Growth Models |
ASTM E 2102 : 2017 | Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.