ASTM E 1418 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Visible Penetrant Testing Using the Water-Washable Process
Hardcopy , PDF
13-08-2021
English
22-08-2016
Committee |
E 07
|
DocumentType |
Standard Practice
|
Pages |
6
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This practice describes procedures for visible liquid penetrant examination utilizing the water-washable process. It is a nondestructive practice for detecting discontinuities that are open to the surface such as cracks, seams, laps, cold shuts, laminations, isolated porosity, through leaks or lack of fusion and is applicable to in-process, final, and maintenance examination. This practice can be effectively used in the examination of nonporous, metallic materials, both ferrous and nonferrous, and of nonmetallic materials such as glazed or fully densified ceramics, and certain nonporous plastics, and glass.
1.2This practice also provides the following references:
1.2.1A reference by which visible penetrant examination procedures using the water-washable process can be reviewed to ascertain their applicability and completeness.
1.2.2For use in the preparation of process specifications dealing with the visible, water-washable liquid penetrant examination of materials and parts. Agreement between the user and the supplier regarding specific techniques is strongly recommended.
1.2.3For use in the organization of the facilities and personnel concerned with the liquid penetrant examination.
1.3This practice does not indicate or suggest criteria for evaluation of the indications obtained. It should be noted, however, that after indications have been produced, they must be interpreted or classified and then evaluated. For this purpose there must be a separate code, specification, or a specific agreement to define the type, size, location, and orientation of indications considered acceptable, and those considered unacceptable.
1.4The values stated in inch-pound units are regarded as standard. SI units given in parentheses are for information only.
1.5Basis of Application—There are areas in this practice that may require agreement between the cognizant engineering organization and the supplier, or specific direction from the cognizant engineering organization. These areas are identified as follows:
1.5.1Penetrant type, method and sensitivity,
1.5.2Accept/reject criteria,
1.5.3Personnel qualification requirements,
1.5.4Grit blasting,
1.5.5Etching,
1.5.6Indication/discontinuity sizing,
1.5.7Total processing time, and
1.5.8Marking of parts.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM E 165/E165M : 2018 | Standard Practice for Liquid Penetrant Testing for General Industry |
ASTM E 2297 : 2015 | Standard Guide for Use of UV-A and Visible Light Sources and Meters used in the Liquid Penetrant and Magnetic Particle Methods |
NFPA 1910:2024 | Standard for the Inspection, Maintenance, Refurbishment, Testing, and Retirement of In-Service Emergency Vehicles and Marine Firefighting Vessels |
ASTM D 1552 : 2003 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
ASTM E 1219 : 2005 | Standard Test Method for Fluorescent Liquid Penetrant Examination Using the Solvent-Removable Process |
ASTM E 1316 : 2011 : REV B | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2015 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2009 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2008 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2010 : REV C | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2020 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2017 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2013 : REV C | Standard Terminology for Nondestructive Examinations |
ASTM D 1552 : 2008 : R2014 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
ASTM E 1316 : 2000 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM D 1552 : 1990 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
ASTM E 1316 : 2019 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM D 1552 : 2016 | Standard Test Method for Sulfur in Petroleum Products by High Temperature Combustion and Infrared (IR) Detection or Thermal Conducitivity Detection (TCD) |
ASTM E 1316 : 2014 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2013 : REV B | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2018 | Standard Terminology for Nondestructive Examinations |
ASTM D 1552 : 2000 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
ASTM E 1316 : 2011 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2007 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2015 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2019 : REV B | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2021 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2013 : REV D | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2000 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2019 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2001 | Standard Terminology for Nondestructive Examinations |
ASTM E 1219 : 2010 | Standard Practice for Fluorescent Liquid Penetrant Testing Using the Solvent-Removable Process |
ASTM E 1316 : 2003 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2018 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2006 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2016 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2002 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM D 1552 : 2016 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products by High Temperature Combustion and Infrared (IR) Detection or Thermal Conductivity Detection (TCD) |
ASTM E 1316 : 2014 : EDT 1 | Standard Terminology for Nondestructive Examinations |
ASTM D 1552 : 2007 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
ASTM E 1219 : 2016 | Standard Practice for Fluorescent Liquid Penetrant Testing Using the Solvent-Removable Process |
ASTM D 1552 : 1995 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
ASTM D 1552 : 2015 | Standard Test Method for Sulfur in Petroleum Products by High Temperature Combustion and IR Detection |
ASTM D 1552 : 2001 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
ASTM E 1316 : 2010 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM D 1552 : 2008 : R2014 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
ASTM E 1316 : 2013 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2021 : REV B | Standard Terminology for Nondestructive Examinations |
ASTM E 1219 : 1999 | Standard Test Method for Fluorescent Liquid Penetrant Examination Using the Solvent-Removable Process |
ASTM E 1316 : 2017 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2016 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2009 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2002 | Standard Terminology for Nondestructive Examinations |
ASTM D 1552 : 2008 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
ASTM E 1316 : 2004 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2007 : REV C | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2010 : REV B | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2013 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM D 1552 : 2016 : R2021 | Standard Test Method for Sulfur in Petroleum Products by High Temperature Combustion and Infrared (IR) Detection or Thermal Conductivity Detection (TCD) |
ASTM E 1316 : 2021 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2007 : REV B | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2005 | Standard Terminology for Nondestructive Testing |
ASTM E 1316 : 2004 | Standard Terminology for Nondestructive Examinations |
ASTM D 1552 : 1983 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
ASTM E 1316 : 2007 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2012 | Standard Terminology for Nondestructive Examinations |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.