ASTM E 1324 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Guide for Measuring Some Electronic Characteristics of Ultrasonic Testing Instruments
Hardcopy , PDF
01-07-2021
English
04-07-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
E 07
|
| DocumentType |
Guide
|
| Pages |
11
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This guide describes procedures for electronically measuring the following performance-related characteristics of some sections of ultrasonic instruments:
1.1.1Power Supply Section:
line regulation,
battery discharge time, and
battery charge time.
1.1.2Pulser Section:
pulse shape,
pulse amplitude,
pulse rise time, pulse length, and
pulse frequency spectrum.
1.1.3Receiver Section:
vertical linearity,
frequency response,
noise and sensitivity, and
dB controls.
1.1.4Time Base Section:
horizontal linearity, and
clock (pulse repetition rate).
1.1.5Gate/Alarm Section:
delay and width,
resolution,
alarm level,
gain uniformity,
analog output, and
back echo gate.
1.2This guide complements Practice E317, D2548 and is not intended for evaluating the performance characteristics of ultrasonic testing instruments on the inspection/production line.
Note 1:No access to internal circuitry is required.
1.3Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM E 127 : 2015 | Standard Practice for Fabrication and Control of Aluminum Alloy Ultrasonic Standard Reference Blocks |
| ASTM E 2491 : 2013 : R2018 | Standard Guide for Evaluating Performance Characteristics of Phased-Array Ultrasonic Testing Instruments and Systems |
| ASTM E 127 : 2020 | Standard Practice for Fabrication and Control of Flat Bottomed Hole Ultrasonic Standard Reference Blocks |
| ASTM E 2533 : 2021 | Standard Guide for Nondestructive Examination of Polymer Matrix Composites Used in Aerospace Applications |
| ASTM E 2373/E2373M : 2019 | Standard Practice for Use of the Ultrasonic Time of Flight Diffraction (TOFD) Technique |
| ASTM E 2373/E2373M : 2014 | Standard Practice for Use of the Ultrasonic Time of Flight Diffraction (TOFD) Technique |
| ASTM E 317 : 2016 | Standard Practice for Evaluating Performance Characteristics of Ultrasonic Pulse-Echo Testing Instruments and Systems without the Use of Electronic Measurement Instruments |
| ASTM E 2775 : 2016 | Standard Practice for Guided Wave Testing of Above Ground Steel Pipework Using Piezoelectric Effect Transduction |
| ASTM E 1316 : 2011 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2015 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2009 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2008 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2010 : REV C | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2020 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2017 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2013 : REV C | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2000 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2019 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2014 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2013 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2018 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2011 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2007 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2015 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2019 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2013 : REV D | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2000 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2019 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2001 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2003 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2018 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2006 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2016 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2002 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2014 : EDT 1 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2010 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2013 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2017 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2016 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2009 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2002 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2004 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2007 : REV C | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2010 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2013 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2021 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2007 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2005 | Standard Terminology for Nondestructive Testing |
| ASTM E 1316 : 2004 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2007 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2012 | Standard Terminology for Nondestructive Examinations |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.