Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM E 1135 : 2019

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Test Method for Comparing the Brightness of Fluorescent Penetrants

Available format(s)

Hardcopy , PDF

Superseded date

12-02-2024

Language(s)

English

Published date

18-03-2019

$108.03
Including GST where applicable

Committee
E 07
DocumentType
Test Method
Pages
3
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This test method describes the techniques for comparing the brightness of the penetrants used in the fluorescent dye penetrant process. This comparison is performed under controlled conditions that eliminate most of the variables present in actual penetrant examination. Thus, the brightness factor is isolated and is measured independently of the other factors which affect the performance of a penetrant system.

1.2The brightness of a penetrant indication is affected by the developer with which it is used. This test method, however, measures the brightness of a penetrant on a convenient filter paper substrate which serves as a substitute for the developer.

1.3The brightness measurement obtained is color-corrected to approximate the color response of the average human eye. Since most examinations are done by human eyes, this number has more practical value than a measurement in units of energy emitted. Also, the comparisons are expressed as a percentage of some chosen standard penetrant because no absolute system of measurement exists at this time.

1.4The measurements made by this standard compare the brightness of a candidate penetrant to that of a standard penetrant when tested according to the technique. There is no known correlation between the results obtained and the brightness of actual flaw indications obtained using the penetrant in inspection.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM F 601 : 2018 Standard Practice for Fluorescent Penetrant Inspection of Metallic Surgical Implants
ASTM E 1417/E1417M : 2016 Standard Practice for Liquid Penetrant Testing
ASTM E 1417/E1417M : 2021 : EDT 1 Standard Practice for Liquid Penetrant Testing

ASTM E 1316 : 2022 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2015 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2020 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2017 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2018 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2015 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2019 : REV B Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2021 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2000 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2024 Standard Terminology for <?Pub Dtl?>Nondestructive Examinations
ASTM E 1316 : 2016 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2021 : REV D Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2014 : EDT 1 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2022 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2021 : REV B Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2017 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2016 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2002 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2023 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2021 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2021 : REV C Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2023 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2023 : REV B Standard Terminology for Nondestructive Examinations

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more