ASTM D 8139 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction
Hardcopy , PDF
11-12-2023
English
11-10-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 04.03, 2017 Defines preformed expansion joint fillers made from closed-cell polypropylene foam materials having suitable compressibility, recovery from compression, nonextruding, and weather-resistant characteristics.
| Committee |
D 04
|
| DocumentType |
Standard
|
| Pages |
2
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This specification covers preformed expansion joint fillers made from closed-cell polypropylene foam materials having suitable compressibility, recovery from compression, nonextruding, and weather-resistant characteristics.
1.1.1Type I, closed-cell polypropylene foam.
1.2These joint fillers are intended for use in concrete pavements in full-depth joints. There are several variations in size with typical thicknesses of 1/2in. (12.7 mm), 3/4in. (19.05 mm), and 1 in. (25.4 mm); typical widths of 31/2in. (88.9 mm), 4 in. (101.6 mm), 5 in. (127 mm), 6 in. (152.5 mm), 7 in. (177.8 mm), 8 in. (203.2 mm), or 48 in. (1.2 m) sheet; and typical lengths of 5 ft (1.52 m) and 10 ft (3.05 m).
1.3The values stated in inch-pound units are to be regarded as the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 5249 : 2010 : R2016 | Standard Specification for Backer Material for Use with Cold- and Hot-Applied Joint Sealants in Portland-Cement Concrete and Asphalt Joints |
| ASTM D 4329 : 2021 | Standard Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of Plastics |
| ASTM D 5249 : 1995 : R2000 | Standard Specification for Backer Material for Use with Cold- and Hot-Applied Joint Sealants in Portland-Cement Concrete and Asphalt Joints |
| ASTM D 1623 : 2017 : REDLINE | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics |
| ASTM D 4329 : 2013 : REDLINE | Standard Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of Plastics |
| ASTM D 1623 : 2003 | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics |
| ASTM D 4329 : 2013 | Standard Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of Plastics |
| ASTM D 545 : 2014 : REDLINE | Standard Test Methods for Preformed Expansion Joint Fillers for Concrete Construction (Nonextruding and Resilient Types) |
| ASTM C 666/C666M : 2015 : REDLINE | Standard Test Method for Resistance of Concrete to Rapid Freezing and Thawing |
| ASTM D 1623 : 2009 | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics |
| ASTM D 1623 : 1978 : R1995 | Standard Test Method for Tensile And Tensile Adhesion Properties Of Rigid Cellular Plastics |
| ASTM D 4329 : 1999 | Standard Practice for Fluorescent UV Exposure of Plastics |
| ASTM D 4329 : 2005 | Standard Practice for Fluorescent UV Exposure of Plastics |
| ASTM D 5249 : 1995 : R2006 | Standard Specification for Backer Material for Use with Cold- and Hot-Applied Joint Sealants in Portland-Cement Concrete and Asphalt Joints |
| ASTM D 1623 : 2017 | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics |
| ASTM C 666/C666M : 2015 | Standard Test Method for Resistance of Concrete to Rapid Freezing and Thawing (Withdrawn 2024) |
| ASTM D 5249 : 2010 | Standard Specification for Backer Material for Use with Cold- and Hot-Applied Joint Sealants in Portland-Cement Concrete and Asphalt Joints |
| ASTM D 1623 : 2017 : R2023 | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics |
| ASTM D 5249 : 2010 : R2021 | Standard Specification for Backer Material for Use with Cold- and Hot-Applied Joint Sealants in Portland Cement Concrete and Asphalt Joints |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.