ASTM D 8082 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Elemental Impurity Limits in Erosion Control Products used for Land Application
Hardcopy , PDF
18-07-2024
English
01-08-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 18
|
| DocumentType |
Standard
|
| Pages |
2
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This standard provides a specification for elemental impurity limits in erosion control products used for land application. Erosion control products may include but are not limited to: hydraulically-applied erosion control products, rolled erosion control products, sediment retention devices, gabions and mattresses, and articulated concrete block revetments.
1.2Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026, unless superseded by this specification.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 653 : 2007 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 3740 : 2012 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 3740 : 2023 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 3740 : 2019 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 3740 : 2004 : REV A : EDT 1 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 3740 : 2008 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 6026 : 2013 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 6026 : 2006 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 3740 : 1999 : REV C | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 3987 : 1985 : R1999 | Standard Test Method for Shake Extraction of Solid Waste with Water |
| ASTM D 653 : 2022 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 653 : 2020 : EDT 1 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 6026 : 1999 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 3740 : 2011 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 6026 : 2001 : EDT 1 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 3740 : 2010 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 653 : 2021 : REV A | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 3987 : 2012 | Standard Practice for Shake Extraction of Solid Waste with Water |
| ASTM D 6026 : 1996 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 3740 : 2004 : REV A | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 3740 : 2001 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 653 : 2021 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 653 : 2021 : REV B | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 6026 : 1996 : EDT 1 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 3740 : 2012 : REV A | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 3740 : 2003 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 6026 : 2021 | Standard Practice for Using Significant Digits and Data Records in Geotechnical Data |
| ASTM D 6026 : 2001 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 3987 : 1985 : R2004 | Standard Test Method for Shake Extraction of Solid Waste with Water |
| ASTM D 3987 : 2006 | Standard Test Method for Shake Extraction of Solid Waste with Water |
| ASTM D 3740 : 2004 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 3987 : 2012 : R2020 | Standard Practice for Shake Extraction of Solid Waste with Water |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.