ASTM D 774/D774M : 1997
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Bursting Strength of Paper
Hardcopy , PDF
11-11-2014
English
31-12-2010
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 15.09, 2009 Deals with the measurements of the bursting strength of paper and paper products occurring as single or laminated flat sheets not over 0.6 mm [0.025 in.] in thickness having a bursting strength of 30 kPa up to 1400 kPa.
| Committee |
D 06
|
| DevelopmentNote |
Supersedes ASTM D 774. (12/2007)
|
| DocumentType |
Test Method
|
| Pages |
4
|
| ProductNote |
Reconfirmed 1997
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1 This test method covers measurements of the bursting strength of paper and paper products occurring as single or laminated flat sheets not over 0.6mm. (0.025 in.) in thickness having a bursting strength of 30 kPa up to 1400 kPa (4 psi up to 200 psi).
1.2 This test method is not intended for use in testing corrugated boxboard, liner board, or hardboards that tend to cut the thin rubber diaphragm.
Note 1- Similar procedures for making bursting strength measurements are found in ISO 2758 and TAPPI 403.
1.3 The values stated in either SI units or in other units shall be regarded seperately as the standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM C 921 : 2010 : R2015 | Standard Practice for Determining the Properties of Jacketing Materials for Thermal Insulation (Withdrawn 2021) |
| ASTM D 8065/D8065M : 2016 | Standard Classification System and Basis for Specification for Specifying Plastic Films |
| ASTM C 1136 : 2017 : REV A | Standard Specification for Flexible, Low Permeance Vapor Retarders for Thermal Insulation |
| ASTM D 3376 : 2018 | Standard Test Methods of Sampling and Testing Pulps to be Used in the Manufacture of Electrical Insulation |
| ASTM C 1423 : 2016 | Standard Guide for Selecting Jacketing Materials for Thermal Insulation |
| ASTM E 832 : 1981 : R2019 | Standard Specification for Laboratory Filter Papers |
| ASTM D 202 : 2017 | Standard Test Methods for Sampling and Testing Untreated Paper Used for Electrical Insulation |
| ASTM D 3664 : 2016 | Standard Specification for Biaxially Oriented Polymeric Resin Film for Capacitors in Electrical Equipment (Withdrawn 2022) |
| ASTM D 5047 : 2017 | Standard Specification for Polyethylene Terephthalate Film and Sheeting |
| ASTM D 1968 : 2019 | Standard Terminology Relating to Paper and Paper Products |
| TAPPI T 403 : 2010 | BURSTING STRENGTH OF PAPER |
| ASTM D 646 : 2013 | Standard Test Method for Mass Per Unit Area of Paper and Paperboard of Aramid Papers (Basis Weight) (Withdrawn 2022) |
| ASTM D 585 : 1997 | Standard Practice for Sampling and Accepting a Single Lot of Paper, Paperboard, Fiberboard, and Related Product |
| ISO 2758:2014 | Paper Determination of bursting strength |
| ASTM D 1968 : 2015 | Standard Terminology Relating to Paper and Paper Products |
| ASTM D 685 : 2017 : REDLINE | Standard Practice for Conditioning Paper and Paper Products for Testing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.