Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 7422 : 2022

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine

Available format(s)

Hardcopy , PDF

Superseded date

19-12-2023

Superseded by

ASTM D 7422 : 2023

Language(s)

English

Published date

14-04-2022

$176.78
Including GST where applicable

Committee
D 02
DocumentType
Test Method
Pages
39
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics, including lead corrosion and wear of piston rings and cylinder liners in an engine equipped with exhaust gas recirculation and running on ultra-low sulfur diesel fuel.2 This test method is commonly referred to as the Mack T-12.

1.1.1This test method also provides the procedure for running an abbreviated length test, which is commonly referred to as the T-12A. The procedures for the T-12 and T-12A are identical with the exception of the items specifically listed in Annex A9. Additionally, the procedure modifications listed in Annex A9 refer to the corresponding section of the T-12 procedure.

1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.2.1Exception—Where there is no direct SI equivalent, such as the units for screw threads, National Pipe Threads/diameters, tubing size, and single source supply equipment specifications.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Annex A6 for specific safety precautions.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D 6750 : 2019 Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur)
ASTM D 5579 : 2019 Standard Test Method for Evaluating the Thermal Stability of Manual Transmission Lubricants in a Cyclic Durability Test
ASTM D 7156 : 2019 Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine
ASTM D 7320 : 2018 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 6984 : 2018 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIF, Spark-Ignition Engine
ASTM D 4485 : 2020 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 5967 : 2021 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
ASTM D 6709 : 2022 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence VIII Spark-Ignition Engine (CLR Oil Test Engine)
ASTM D 6681 : 2017 Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1P Test Procedure
ASTM D 6593 : 2018 : EDT 1 Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions
ASTM D 6750 : 2023 Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur)
ASTM D 5579 : 2019 : EDT 1 Standard Test Method for Evaluating the Thermal Stability of Manual Transmission Lubricants in a Cyclic Durability Test
ASTM D 5966 : 2022 Standard Test Method for Evaluation of Engine Oils for Roller Follower Wear in Light-Duty Diesel Engine
ASTM D 7320 : 2018 : EDT 1 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 6984 : 2018 : EDT 1 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIF, Spark-Ignition Engine
ASTM D 6681 : 2023 Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1P Test Procedure

ASTM E 29 : 2013 : R2019 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM D 613 : 2018 : REV A Standard Test Method for Cetane Number of Diesel Fuel Oil
ASTM D 86 : 2023 Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
ASTM D 664 : 2017 : REV A Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
ASTM D 1319 : 2018 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 86 : 2020 : REV A Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
ASTM D 482 : 2013 Standard Test Method for Ash from Petroleum Products
ASTM D 4052 : 2018 : REV A Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 613 : 2023 Standard Test Method for Cetane Number of Diesel Fuel Oil
ASTM D 86 : 2018 Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
ASTM D 4175 : 2022 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 445 : 2021 : EDT 2 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 93 : 2019 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
ASTM D 445 : 2017 : REV A Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 4175 : 2020 : REV B : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 86 : 2019 Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
ASTM D 2709 : 2016 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D 4175 : 2022 : REV A Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 287 : 2022 Standard Test Method for API Gravity of Crude Petroleum and Petroleum Products (Hydrometer/Method)
ASTM D 976 : 2021 Standard Test Method for Calculated Cetane Index of Distillate Fuels
ASTM D 613 : 2018 : REV A : EDT 1 Standard Test Method for Cetane Number of Diesel Fuel Oil
ASTM D 86 : 2012 Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure
ASTM D 4739 : 2017 Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
ASTM D 4175 : 2023 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4485 : 2020 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 4175 : 2022 : REV A : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 976 : 2021 : EDT 1 Standard Test Method for Calculated Cetane Index of Distillate Fuels
ASTM D 86 : 2020 : REV B Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
ASTM D 86 : 2016 : REV A Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
ASTM D 445 : 2019 : REV A Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 97 : 2017 : REV B Standard Test Method for Pour Point of Petroleum Products
ASTM D 2500 : 2017 : REV A Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels
ASTM D 287 : 2012 : REV B Standard Test Method for API Gravity of Crude Petroleum and Petroleum Products (Hydrometer Method)
ASTM D 4294 : 2016 : EDT 1 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 5453 : 2016 : EDT 1 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 445 : 2019 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 4175 : 2023 : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 2709 : 2022 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D 4175 : 2022 : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 130 : 2018 Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test
ASTM D 2622 : 2021 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 97 : 2017 : REV B : R2022 Standard Test Method for Pour Point of Petroleum Products
ASTM D 664 : 2011 : REV A Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
ASTM D 445 : 2021 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 86 : 2020 Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
ASTM D 5186 : 2022 Standard Test Method for Determination of the Aromatic Content and Polynuclear Aromatic Content of Diesel Fuels By Supercritical Fluid Chromatography
ASTM D 4739 : 2023 Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
ASTM D 524 : 2015 Standard Test Method for Ramsbottom Carbon Residue of Petroleum Products
ASTM D 4485 : 2022 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 4052 : 2022 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 5453 : 2019 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 445 : 2018 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 86 : 2015 Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
ASTM D 2500 : 2023 Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels
ASTM D 445 : 2021 : EDT 1 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 86 : 2017 Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
ASTM D 1319 : 2019 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 5186 : 2020 Standard Test Method for Determination of the Aromatic Content and Polynuclear Aromatic Content of Diesel Fuels By Supercritical Fluid Chromatography
ASTM D 445 : 2023 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 130 : 2012 Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test
ASTM D 4485 : 2022 : EDT 1 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 2622 : 2016 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 93 : 2018 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
ASTM D 287 : 2012 : REV B : R2019 Standard Test Method for API Gravity of Crude Petroleum and Petroleum Products (Hydrometer Method)
ASTM E 29 : 2022 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more