ASTM D 6693/D6693M : 2004 : R2015 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Determining Tensile Properties of Nonreinforced Polyethylene and Nonreinforced Flexible Polypropylene Geomembranes
Hardcopy , PDF
12-08-2020
English
01-05-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 04.13, 2017 Defines the determination of the tensile properties of nonreinforced geomembranes in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, and machine speed.
| Committee |
D 35
|
| DevelopmentNote |
Supersedes ASTM D 6693. (06/2015)
|
| DocumentType |
Test Method
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the determination of the tensile properties of nonreinforced geomembranes in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, and machine speed.
1.2This test method can be used for testing materials thickness between 0.25 mm [0.010 in.] and 6.3 mm [0.25 in.].
Note 1:This test method is not intended to cover precise physical procedures. The constant rate of crosshead movement of this test lacks accuracy from a theoretical standpoint. A wide difference may exist between the rate of crosshead movement and the rate of strain of the specimen indicating that the testing speeds specified may disguise important effects or characteristics of these materials in the plastic state. Further, it is realized that variations in the thicknesses of test specimens, as permitted by this test method, produce variations in the surface-volume ratios of such specimens, and that these variations may influence the test results. Hence, where directly comparable results are desired, all samples should be of equal thickness. Special additional tests should be used where more precise physical data are needed.
1.3Test data obtained by this test method are relevant and may be appropriate for use in engineering design with consideration of test conditions as compared with in-service conditions.
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 6495/D6495M : 2018 : REDLINE | Standard Guide for Acceptance Testing Requirements for Geosynthetic Clay Liners |
| ASTM D 5889/D5889M : 2018 : REDLINE | Standard Practice for Quality Control of Geosynthetic Clay Liners |
| ASTM D 4439 : 2020 | Standard Terminology for Geosynthetics |
| ASTM D 4439 : 2015 | Standard Terminology for Geosynthetics |
| ASTM D 4000 : 2013 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 5199 : 2012 : R2019 | Standard Test Method for Measuring the Nominal Thickness of Geosynthetics |
| ASTM D 4000 : 2003 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2000 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2012 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2009 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2011 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4439 : 2011 | Standard Terminology for Geosynthetics |
| ASTM D 5199 : 2001 | Standard Test Method for Measuring the Nominal Thickness of Geosynthetics |
| ASTM D 4000 : 2004 : EDT 1 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4439 : 2015 : REV A | Standard Terminology for Geosynthetics |
| ASTM D 4439 : 2002 | Standard Terminology for Geosynthetics |
| ASTM D 4000 : 2009 : REV B | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2000 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2010 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4439 : 2017 | Standard Terminology for Geosynthetics |
| ASTM D 4000 : 2007 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2009 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2001 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2008 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4439 : 2001 | Standard Terminology for Geosynthetics |
| ASTM D 4439 : 2014 | Standard Terminology for Geosynthetics |
| ASTM D 4000 : 2001 : REV A : EDT 1 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 5199 : 2012 | Standard Test Method for Measuring the Nominal Thickness of Geosynthetics |
| ASTM D 4000 : 2004 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 5199 : 2011 | Standard Test Method for Measuring the Nominal Thickness of Geosynthetics |
| ASTM D 4439 : 2004 | Standard Terminology for Geosynthetics |
| ASTM D 4439 : 2017-08 | TERMINOLOGY FOR GEOSYNTHETICS |
| ASTM D 4000 : 2010 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 5994/D5994M : 2010 : R2015 : EDT 1 | Standard Test Method for Measuring Core Thickness of Textured Geomembranes |
| ASTM D 5199 : 2001 : R2006 | Standard Test Method for Measuring the Nominal Thickness of Geosynthetics |
| ASTM D 4439 : 2000 | Standard Terminology for Geosynthetics |
| ASTM D 4000 : 2003 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4439 : 2018 | Standard Terminology for Geosynthetics |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 4000 : 2016 : REDLINE | Standard Classification System for Specifying Plastic Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.