Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 6595 : 2017 : REDLINE

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Test Method for Determination of Wear Metals and Contaminants in Used Lubricating Oils or Used Hydraulic Fluids by Rotating Disc Electrode Atomic Emission Spectrometry

Available format(s)

PDF

Superseded date

14-10-2022

Language(s)

English

Published date

10-05-2017

$122.77
Including GST where applicable

CONTAINED IN VOL. 05.03, 2018 Defines the determination of wear metals and contaminants in used lubricating oils and used hydraulic fluids by rotating disc electrode atomic emission spectroscopy (RDE-AES).

Committee
D 02
DocumentType
Redline
Pages
6
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

1.1This test method covers the determination of wear metals and contaminants in used lubricating oils and used hydraulic fluids by rotating disc electrode atomic emission spectroscopy (RDE-AES).

1.2This test method provides a quick indication for abnormal wear and the presence of contamination in new or used lubricants and hydraulic fluids.

1.3This test method uses oil-soluble metals for calibration and does not purport to relate quantitatively the values determined as insoluble particles to the dissolved metals. Analytical results are particle size dependent and low results may be obtained for those elements present in used oil samples as large particles.

1.4The test method is capable of detecting and quantifying elements resulting from wear and contamination ranging from dissolved materials to particles approximately 10 μm in size.

1.5The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5.1The preferred units are mg/kg (ppm by mass).

1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D 7578 : 2015-06 GUIDE FOR CALIBRATION REQUIREMENTS FOR ELEMENTAL ANALYSIS OF PETROLEUM PRODUCTS AND LUBRICANTS
ASTM D 7776 : 2012 Standard Guide for Self-Assessment of Quality System Practices in Petroleum Products and Lubricant Testing Laboratories (Withdrawn 2017)
DD ISO/TS 11365:2011 Petroleum and related products. Guidance for the maintenance and use of triaryl phosphate ester turbine-control fluids
MIL-PRF-32538 Base Document:2015 LUBRICATING OIL, HELICOPTER TRANSMISSION SYSTEM, SYNTHETIC BASE, NATO CODE NUMBER: O-165
ASTM D 7720 : 2011 : R2017 Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination
ASTM D 8120 : 2017 Standard Test Method for Ferrous Debris Quantification
ASTM D 8128 : 2017 Standard Guide for Monitoring Failure Mode Progression in Industrial Applications with Rolling Element Ball Type Bearings
16/30323482 DC : 0 BS ISO 11365 - PETROLEUM AND RELATED PRODUCTS - MAINTENANCE AND USE GUIDE FOR TRIARYL PHOSPHATE ESTER TURBINE CONTROL FLUIDS
ASTM D 7417 : 2017 : REDLINE Standard Test Method for Analysis of In-Service Lubricants Using Particular Four-Part Integrated Tester (Atomic Emission Spectroscopy, Infrared Spectroscopy, Viscosity, and Laser Particle Counter)
SAE AS 5780 : 2018 SPECIFICATION FOR AERO AND AERO-DERIVED GAS TURBINE ENGINE LUBRICANTS
ISO/TS 11365:2011 Petroleum and related products Guidance for the maintenance and use of triaryl phosphate ester turbine-control fluids
ASTM D 6813 : 2002 : REV A : R2007 Standard Guide for Performance Evaluation of Hydraulic Fluids for Piston Pumps
ASTM D 6813 : 2002 Standard Guide for Performance Evaluation of Hydraulic Fluids for Piston Pumps
ASTM D 6813 : 2002 : REV A : R2013 Standard Guide for Performance Evaluation of Hydraulic Fluids for Piston Pumps (Withdrawn 2015)
ASTM D 6813 : 2002 : REV A Standard Guide for Performance Evaluation of Hydraulic Fluids for Piston Pumps
BS ISO 18436-5:2012 Condition monitoring and diagnostics of machines. Requirements for qualification and assessment of personnel Lubricant laboratory technician/analyst
MIL-DTL-85694 Revision A:2013 Spectrometric Oil Standards
ASTM D 7596 : 2014 : REDLINE Standard Test Method for Automatic Particle Counting and Particle Shape Classification of Oils Using a Direct Imaging Integrated Tester
ISO 11365:2017 Petroleum and related products — Requirements and guidance for the maintenance of triaryl phosphate ester turbine control fluids
ASTM D 7919:2014 Standard Guide for Filter Debris Analysis (FDA) Using Manual or Automated Processes
ISO 18436-5:2012 Condition monitoring and diagnostics of machines — Requirements for qualification and assessment of personnel — Part 5: Lubricant laboratory technician/analyst
BS ISO 11365:2017 Petroleum and related products. Requirements and guidance for the maintenance of triaryl phosphate ester turbine control fluids
08/30190684 DC : DRAFT OCT 2008 BS ISO 18436-5 - CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - REQUIREMENTS FOR QUALIFICATION AND ASSESSMENT OF PERSONNEL - PART 5: LUBRICANT LABORATORY TECHNICIAN/ANALYST
ASTM D 7720:2011 Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination
MIL-PRF-23699 Revision G:2014 Lubricating Oil, Aircraft Turbine Engine, Synthetic Base, NATO Code Numbers: O-152, O-154, O-156, and O-167
ASTM D 7919 : 2014 : R2017 Standard Guide for Filter Debris Analysis (FDA) Using Manual or Automated Processes
UNI ISO 18436-5 : 2013 CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - REQUIREMENTS FOR QUALIFICATION AND ASSESSMENT OF PERSONNEL - PART 5: LUBRICANT LABORATORY TECHNICIAN/ANALYST

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more