ASTM D 6497/D6497M : 2002 : R2015 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Guide for Mechanical Attachment of Geomembrane to Penetrations or Structures
Hardcopy , PDF
13-08-2021
English
12-06-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 04.13, 2017 Defines procedures that can be employed to mechanically attach fabricated geomembranes to structures, pipes, etc.
| Committee |
D 35
|
| DevelopmentNote |
Supersedes ASTM D 6497. (06/2015)
|
| DocumentType |
Guide
|
| Pages |
13
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This guide covers procedures that can be employed to mechanically attach fabricated geomembranes to structures, pipes, etc.
1.2This guide does not address all problems or situations a geomembrane installer or design engineer may face in the attachment of geomembranes to structures, pipes, etc. The sole purpose of this standard guide is to point out typical problems with geomembrane attachments and clearly state objectives of each component of the geomembrane attachment(s).
1.3This guide has been generated for geomembrane application(s); however, a geomembrane installer or design engineer, or both, may find portions of this guide applicable to other geosynthetics.
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 4439 : 2020 | Standard Terminology for Geosynthetics |
| ASTM D 4439 : 2015 | Standard Terminology for Geosynthetics |
| ASTM D 4848 : 1998 : R2004 : EDT 1 | Standard Terminology Related to Force, Deformation and Related Properties of Textiles |
| ASTM D 4848 : 1998 : R2018 | Standard Terminology Related to Force, Deformation and Related Properties of Textiles |
| ASTM D 4439 : 2011 | Standard Terminology for Geosynthetics |
| ASTM D 4439 : 2015 : REV A | Standard Terminology for Geosynthetics |
| ASTM D 4439 : 2002 | Standard Terminology for Geosynthetics |
| ASTM D 4439 : 2017 | Standard Terminology for Geosynthetics |
| ASTM D 4848 : 1998 | Standard Terminology of Force, Deformation and Related Properties of Textiles |
| ASTM F 118 : 2013 : REDLINE | Standard Definitions of Terms Relating to Gaskets |
| ASTM D 4439 : 2001 | Standard Terminology for Geosynthetics |
| ASTM D 4439 : 2014 | Standard Terminology for Geosynthetics |
| ASTM D 4439 : 2004 | Standard Terminology for Geosynthetics |
| ASTM D 4439 : 2017-08 | TERMINOLOGY FOR GEOSYNTHETICS |
| ASTM D 4439 : 2000 | Standard Terminology for Geosynthetics |
| ASTM D 4439 : 2018 | Standard Terminology for Geosynthetics |
| ASTM D 4848 : 1998 : R2004 | Standard Terminology of Force, Deformation and Related Properties of Textiles |
| ASTM D 4848 : 1998 : R2012 | Standard Terminology Related to Force, Deformation and Related Properties of Textiles |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.