Customer Support: 131 242

  • Shopping Cart
    There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 6088 : 2006 : R2016

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Practice for Installation of Geocomposite Pavement Drains

Available format(s)

Hardcopy , PDF

Superseded date

17-06-2022

Language(s)

English

Published date

15-06-2016

$122.77
Including GST where applicable

CONTAINED IN VOL. 04.13, 2017 Defines recommendations and identifies pertinent areas of consideration for the installation of buried geocomposite drains used for highway edgedrains, underdrains, or other pavement drainage applications meeting the requirements of Specification D 7001.

Committee
D 35
DocumentType
Standard Practice
Pages
9
ProductNote
Reconfirmed 2016
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This practice covers recommendations and identifies pertinent areas of consideration for the installation of buried geocomposite drains used for highway edgedrains, under-drains, or other pavement drainage applications meeting the requirements of Specification D7001. These recommendations are intended as guidelines for developing a satisfactory construction and installation method to minimize installation-caused deformation or damage and to provide long-term performance of these products. It is also intended as a guideline for ensuring a stable underground environment for these materials under a wide range of service conditions. Because of the numerous and diverse product designs available and the inherent variability of natural ground conditions, achieving satisfactory performance of any one product may require review by the engineer and modification to provisions contained herein to meet specific project requirements.

1.2The scope of this practice necessarily excludes product performance criteria such as compressibility in any plane, flow capacity, inlet capacity, or geotextile selection and use. It is, therefore, incumbent upon the product manufacturer, specifier, and project engineer to verify that the product specified for an intended application, when installed according to procedures outlined in this practice, will provide satisfactory long term performance according to criteria established by the owner for that application. A commentary of product performance and installation factors important in achieving a satisfactory installation is included in Appendix X1.

1.3The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM D 7001 : 2006 : R2011 Standard Specification for Geocomposites for Pavement Edge Drains and Other High-Flow Applications

ASTM D 2321 : 2005 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM D 4439 : 2020 Standard Terminology for Geosynthetics
ASTM D 2321 : 2009 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM D 2487 : 2017 : EDT 1 Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
ASTM D 2321 : 2014 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM D 4439 : 2015 Standard Terminology for Geosynthetics
ASTM D 653 : 2007 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 4318 : 2005 Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils
ASTM D 3839 : 2014 Standard Guide for Underground Installation of “Fiberglass” (Glass-Fiber Reinforced Thermosetting-Resin) Pipe
ASTM F 412 : 2020 : REV A Standard Terminology Relating to Plastic Piping Systems
ASTM D 698 : 2000 Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12,400 ft-lbf/ft<sup>3</sup> (600 kN-m/m<sup>3</sup>))
ASTM F 412 : 2021 Standard Terminology Relating to Plastic Piping Systems
ASTM D 7001 : 2006 : R2011 Standard Specification for Geocomposites for Pavement Edge Drains and Other High-Flow Applications
ASTM D 698 : 2012 : R2021 Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12,400 ft-lbf/ft<sup>3</sup> (600 kN-m/m<sup>3</sup>))
ASTM D 2321 : 2018 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM D 2321 : 2011 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM D 7001 : 2004 Standard Specification for Geocomposites for Pavement Edge Drains and Other High-Flow Applications
ASTM D 4439 : 2011 Standard Terminology for Geosynthetics
ASTM D 2321 : 2000 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM D 4318 : 2010 Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils
ASTM D 3839 : 2002 : EDT 1 Standard Guide for Underground Installation of "Fiberglass" (Glass-FiberReinforced Thermosetting-Resin) Pipe
ASTM D 4318 : 2000 Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils
ASTM D 4439 : 2015 : REV A Standard Terminology for Geosynthetics
ASTM D 7001 : 2005 Standard Specification for Geocomposites for Pavement Edge Drains and Other High-Flow Applications
ASTM D 3839 : 2014 : REDLINE Standard Guide for Underground Installation of “Fiberglass” (Glass-Fiber Reinforced Thermosetting-Resin) Pipe
ASTM D 4439 : 2002 Standard Terminology for Geosynthetics
ASTM D 2321 : 2004 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM D 698 : 2013-05 TEST METHODS FOR LABORATORY COMPACTION CHARACTERISTICS OF SOIL USING STANDARD EFFORT (12400 FT-LBF/FT[3] (600 KN-M/M[3]))
ASTM D 8 : 2022 Standard Terminology Relating to Materials for Roads and Pavements
ASTM D 420 : 1998 Guide to Site Characterization for Engineering, Design, and Construction Purposes
ASTM D 653 : 2020 : EDT 1 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 4439 : 2017 Standard Terminology for Geosynthetics
ASTM D 2321 : 2014 : EDT 1 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM D 2321 : 1974 Recommended Practice for Underground Installation Of Flexible Thermoplastic Sewer Pipe
ASTM D 2321 : 2004 : EDT 1 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM D 653 : 2021 : REV A Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 7001 : 2020 Standard Specification for Geocomposites for Pavement Edge Drains and Other High-Flow Applications
ASTM D 4318 : 2017 : EDT 1 Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils
ASTM D 8 : 2021 Standard Terminology Relating to Materials for Roads and Pavements
ASTM D 2487 : 2006 : EDT 1 Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
ASTM D 653 : 2021 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 653 : 2021 : REV B Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 4439 : 2001 Standard Terminology for Geosynthetics
ASTM D 4439 : 2014 Standard Terminology for Geosynthetics
ASTM D 4318 : 2010 : EDT 1 Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils
ASTM D 8 : 2019 Standard Terminology Relating to Materials for Roads and Pavements
ASTM D 3839 : 1994 : REV A Standard Practice for Underground Installation of "Fiberglass" (Glass-Fiber- Reinforced Thermosetting-Resin) Pipe
ASTM D 2321 : 2008 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM D 7001 : 2006 Standard Specification for Geocomposites for Pavement Edge Drains and Other High-Flow Applications
ASTM D 4439 : 2004 Standard Terminology for Geosynthetics
ASTM D 3839 : 2014 : R2019 Standard Guide for Underground Installation of “Fiberglass” (Glass-Fiber Reinforced Thermosetting-Resin) Pipe
ASTM D 4318 : 2017 Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils
ASTM D 2487 : 2010 Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
ASTM D 4439 : 2017-08 TERMINOLOGY FOR GEOSYNTHETICS
ASTM D 2487 : 2000 Standard Classification of Soils for Engineering Purposes (Unified Soil Classification System)
ASTM D 2487 : 2006 Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
ASTM D 8 : 2020 : REV A Standard Terminology Relating to Materials for Roads and Pavements
ASTM D 4439 : 2000 Standard Terminology for Geosynthetics
ASTM D 2487 : 2011 Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
ASTM D 2321 : 2020 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM D 3839 : 2002 Standard Guide for Underground Installation of "Fiberglass" (Glass-FiberReinforced Thermosetting-Resin) Pipe
ASTM D 2487 : 2017 Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
ASTM D 4439 : 2018 Standard Terminology for Geosynthetics
ASTM D 2487 : 1969 : R1975 Standard Test Method for Classification Of Soils For Engineering Purposes
ASTM D 653 : 2014 : REDLINE Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 698 : 2012 : EDT 2 Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12 400 ft-lbf/ft<sup>3</sup> (600 kN-m/m<sup>3</sup>))
ASTM D 3839 : 2008 Standard Guide for Underground Installation of <span class='unicode'>“</span>Fiberglass<span class='unicode'>”</span> (Glass-FiberReinforced Thermosetting-Resin) Pipe

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.