Customer Support: 131 242

  • Shopping Cart
    There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 5853 : 2017 : REV A

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Test Method for Pour Point of Crude Oils

Available format(s)

Hardcopy , PDF

Superseded date

20-05-2024

Superseded by

ASTM D 5853 : 2024

Language(s)

English

Published date

05-02-2018

$122.77
Including GST where applicable

Committee
D 02
DocumentType
Test Method
Pages
10
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This test method covers two procedures for the determination of the pour point temperatures of crude oils down to −36 °C. Procedure A provides a measure of the maximum (upper) pour point temperature and is described in 9.1. Procedure B provides a measure of the minimum (lower) pour point temperature and is described in 9.2.

1.2The use of this test method is limited to use for crude oils. Pour point temperatures of other petroleum products can be determined by Test Method D97.

1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.4WARNING—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury and/or mercury containing products in your state or country may be prohibited by law.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D 6377 : 2016 Standard Test Method for Determination of Vapor Pressure of Crude Oil: VPCR<inf>x</inf > (Expansion Method)
ASTM F 3337 : 2019 Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil
ASTM D 4057 : 2012 : R2018 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 97 : 2017 : REV B Standard Test Method for Pour Point of Petroleum Products
ASTM D 7975 : 2014 Standard Test Method for Determination of Vapor Pressure of Crude Oil: <brk/>VPCR<inf >x</inf>-F(Tm°C)(Manual Expansion Field Method)
ASTM D 7975 : 2022 Standard Test Method for Determination of Vapor Pressure of Crude Oil: <brk/>VPCR<inf >x</inf>-F(Tm°C) (Manual Expansion Field Method)
ASTM F 3337 : 2023 Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil
ASTM D 8164 : 2021 Standard Guide for Digital Contact Thermometers for Petroleum Products, Liquid Fuels, and Lubricant Testing
ASTM D 6377 : 2020 Standard Test Method for Determination of Vapor Pressure of Crude Oil: VPCR<inf>x</inf > (Expansion Method)
ASTM D 8278 : 2020 Standard Specification for Digital Contact Thermometers for Test Methods Measuring Flow Properties of Fuels and Lubricants

ASTM D 4057 : 2019 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 4057 : 1995 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM E 2877 : 2012 : EDT 1 Standard Guide for Digital Contact Thermometers
ASTM D 4177 : 2016 : EDT 1 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 4177 : 1995 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 4057 : 2012 : R2018 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM E 2251 : 2007 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
ASTM E 2251 : 2003 : REV A Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
ASTM D 7962 : 2015 Standard Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift
ASTM D 4057 : 1981 : EDT 2 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 7962 : 2021 Standard Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift
ASTM E 2251 : 2003 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
ASTM D 7962 : 2016 Standard Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift
ASTM E 2251 : 2014 : R2021 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
ASTM D 4057 : 2006 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM E 77 : 2014 : EDT 1 Standard Test Method for Inspection and Verification of Thermometers
ASTM D 4177 : 2015 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM E 2251 : 2010 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
ASTM D 4057 : 2012 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 7962 : 2015 : REV A Standard Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift
ASTM E 2251 : 2011 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
ASTM E 2877 : 2012 : R2019 Standard Guide for Digital Contact Thermometers
ASTM E 2251 : 2014 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
ASTM D 4177 : 2022 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 4177 : 1995 : R2010 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 4177 : 1995 : R2000 Standard Practice for Automatic Sampling of Peroleum and Petroleum Products
ASTM D 130 : 2018 Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test
ASTM E 2877 : 2012 Standard Guide for Standard Guide for Digital Contact Thermometers
ASTM D 97 : 2017 : REV B : R2022 Standard Test Method for Pour Point of Petroleum Products
ASTM E 1 : 2014 : R2020 Standard Specification for ASTM Liquid-in-Glass Thermometers
ASTM D 4057 : 2022 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 4177 : 2016 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 4177 : 2020 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 4177 : 1995 : R2005 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 4057 : 1995 : R2000 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 4177 : 2022 : EDT 1 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM E 77 : 1998 Standard Test Method for Inspection and Verification of Thermometers
ASTM D 4177 : 2015 : REV A Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 4057 : 2006 : R2011 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM E 77 : 2014 : R2021 Standard Test Method for Inspection and Verification of Thermometers
ASTM D 7962 : 2017 Standard Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift
ASTM D 130 : 2012 Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.