ASTM D 5677 : 2017
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings, Adhesive Bonded Joint Type, for Aviation Jet Turbine Fuel Lines
Available format(s)
Hardcopy , PDF
Superseded date
19-10-2023
Superseded by
Language(s)
English
Published date
27-03-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 20
|
| DocumentType |
Standard
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers a reinforced plastic pipe and fittings system made from epoxy resin and glass-fiber reinforcement, together with adhesive for joint assembly, intended for service up to 150°F (65.6°C) and 150-psig (1034-kPa) operating pressure and surges up to 275 psig (1896 kPa) in aviation jet turbine fuel lines installed below ground.
1.2The dimensionless designator NPS has been substituted in this specification for such traditional terms as nominal diameter, size, and nominal size.
1.3The values stated in inch-pound units are to be regarded as standard. The values in parentheses are for information only.
1.4The following safety hazards caveat pertains only to the test method portion, Section 9, of this specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1:There is no known ISO equivalent to this standard.
| ASTM D 3241 : 2008 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels (JFTOT Procedure) |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 3241 : 2009 : EDT 1 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 3241 : 2019 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 3241 : 2005 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels (JFTOT Procedure) |
| ASTM D 3241 : 2020 : REV C | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 3951 : 2010 | Standard Practice for Commercial Packaging |
| ASTM D 2310 : 2001 | Standard Classification for Machine-Made "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
| ASTM D 1655 : 2008 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3241 : 2020 : REV B | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 1655 : 2011 : REV B | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2012 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3241 : 2001 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels (JFTOT Procedure) |
| ASTM D 1655 : 2006 : REV B | Standard Specification for Aviation Turbine Fuels |
| ASTM F 412 : 2020 : REV A | Standard Terminology Relating to Plastic Piping Systems |
| ASTM F 412 : 2021 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM D 1655 : 2006 : REV C | Standard Specification for Aviation Turbine Fuels |
| ASTM D 5685 : 2005 | Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings |
| ASTM D 3241 : 2006 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels (JFTOT Procedure) |
| ASTM D 1655 : 2021 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2018 : REV B | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2005 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3951 : 1998 | Standard Practice for Commercial Packaging |
| ASTM D 1655 : 2017 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3241 : 2014 : EDT 1 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 3241 : 2002 : REV A | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels (JFTOT Procedure) |
| ASTM D 5685 : 2001 | Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings |
| ASTM D 2310 : 2006 : R2012 | Standard Classification for Machine-Made “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe (Withdrawn 2017) |
| ASTM D 1655 : 2014 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2001 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 2412 : 2011 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 3241 : 2014 : REV A | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 1655 : 2011 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3241 : 2017 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 2412 : 2002 : R2008 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 1655 : 2020 : REV D | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3241 : 2020 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 2310 : 2006 | Standard Classification for Machine-Made "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
| ASTM D 1655 : 2022 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2006 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 883 : 2022 | Standard Terminology Relating to Plastics |
| ASTM D 3241 : 2018 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 1655 : 2022 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3567 : 1997 : R2006 | Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
| ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
| ASTM D 3241 : 2014 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 3241 : 2015 : EDT 1 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 3241 : 2017 : REV A | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 1655 : 2015 : REV D | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2008 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 2412 : 2010 : REV A | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 1655 : 2002 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1655 : 2006 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 3241 : 2023 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 1655 : 2016 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2010 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2017 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3951 : 2015 | Standard Practice for Commercial Packaging |
| ASTM D 1655 : 2000 : REV B | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3241 : 2019 : REV A | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 1655 : 2015 : REV C | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3241 : 2009 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels (JFTOT Procedure) |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 3567 : 2017 : R2022 | Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
| ASTM D 3241 : 2015 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 3951 : 2018 | Standard Practice for Commercial Packaging |
| ASTM D 1655 : 2015 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 2412 : 1996 : REV A | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 1655 : 2007 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1599 : 2014 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1655 : 2015 : REV B | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1599 : 2014 : EDT 1 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1655 : 2021 : REV B | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3241 : 2008 : REV A | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels (JFTOT Procedure) |
| ASTM D 2412 : 2002 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 3567 : 1997 : R2002 | Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
| ASTM D 3241 : 2001 : EDT 1 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels (JFTOT Procedure) |
| ASTM D 1655 : 2012 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM F 1173 : 2001 : R2018 | Standard Specification for Thermosetting Resin Fiberglass Pipe Systems to Be Used for Marine Applications |
| ASTM D 1599 : 2018 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1655 : 2023 | Standard Specification for Aviation Turbine Fuels |
| ASTM F 1173 : 2001 : R2012 | Standard Specification for Thermosetting Resin Fiberglass Pipe Systems to Be Used for Marine Applications |
| ASTM D 1655 : 2014 : REV B | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2015 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1599 : 1999 : R2011 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1655 : 1985 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2016 : REV C | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1599 : 1999 : EDT 1 | Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1655 : 2004 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 2412 : 2021 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 3241 : 2005 : REV B | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels (JFTOT Procedure) |
| ASTM D 3241 : 2002 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels (JFTOT Procedure) |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 3241 : 2015 : EDT 2 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 1655 : 2016 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3241 : 2014 : REV B | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM F 1173 : 2001 | Standard Specification for Thermosetting Resin Fiberglass Pipe Systems to Be Used for Marine Applications |
| ASTM D 1655 : 2021 | Standard Specification for Aviation Turbine Fuels |
| ASTM F 1173 : 2001 : R2023 | Standard Specification for Thermosetting Resin Fiberglass Pipe Systems to Be Used for Marine Applications |
| ASTM F 412 : 2023 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM D 381 : 2019 | Standard Test Method for Gum Content in Fuels by Jet Evaporation |
| ASTM D 1655 : 2021 : REV C | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2004 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2014 : REV C | Standard Specification for Aviation Turbine Fuels |
| ASTM D 381 : 2022 | Standard Test Method for Gum Content in Fuels by Jet Evaporation |
| ASTM D 1655 : 2016 : REV B | Standard Specification for Aviation Turbine Fuels |
| ASTM F 1173 : 1995 | Standard Specification for Thermosetting Resin Fiberglass Pipe Systems to Be Used for Marine Applications |
| ASTM D 1655 : 2007 : EDT 1 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3241 : 2019 : REV B | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 1655 : 2000 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3567 : 1997 | Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
| ASTM D 1655 : 2013 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2015 : REV D : EDT 1 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 5685 : 1995 | Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings |
| ASTM D 3241 : 2002 : REV A : EDT 1 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels (JFTOT Procedure) |
| ASTM D 1655 : 2019 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 381 : 2012 : R2017 | Standard Test Method for Gum Content in Fuels by Jet Evaporation |
| ASTM D 3241 : 1998 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels (JFTOT Procedure) |
| ASTM D 5685 : 2019 | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings |
| ASTM D 1655 : 2006 : REV D | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2003 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3241 : 2011 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 5685 : 2002 | Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings |
| ASTM D 1655 : 2014 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2003 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2009 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3241 : 2005 : REV A | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels (JFTOT Procedure) |
| ASTM D 1599 : 1999 : R2005 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 3241 : 2013 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 1655 : 2011 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3241 : 2014 : REV B : EDT 1 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 1655 : 2020 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3567 : 2017 | Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
| ASTM D 1655 : 2009 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2018 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2020 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2018 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 5685 : 2011 | Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings |
| ASTM D 3241 : 2016 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM F 1173 : 2001 : R2006 | Standard Specification for Thermosetting Resin Fiberglass Pipe Systems to Be Used for Marine Applications |
| ASTM D 2412 : 2011 : R2018 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 3241 : 2012 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 2310 : 1997 | Standard Classification for Machine-Made "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
| ASTM D 1599 : 1999 | Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 3567 : 1997 : R2011 | Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
| ASTM D 1655 : 2019 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 2412 : 2010 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 1655 : 2013 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3241 : 2004 | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels (JFTOT Procedure) |
| ASTM D 3241 : 2016 : REV A | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
| ASTM D 3241 : 2011 : REV A | Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.