ASTM D 546 : 2017 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Sieve Analysis of Mineral Filler for Asphalt Paving Mixtures
15-10-2024
English
01-04-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 04.03, 2017 Describes the sieve analysis of mineral fillers used in bituminous paving mixtures.
| Committee |
D 04
|
| DevelopmentNote |
Also numbered as AASHTO T 37. (04/2017)
|
| DocumentType |
Redline
|
| Pages |
2
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This test method covers the sieve analysis of mineral fillers used in asphalt paving mixtures.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
Note 1:Regarding sieves, per Specification E11, “the values stated in SI units shall be considered standard for the dimensions of the wire cloth openings and the diameter of the wires used in the wire cloth.” When sieve mesh sizes are referenced, the alternate inch-pound designations are provided for information purposes and enclosed in parentheses.
1.3The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| AASHTO M 17 : 2011 | SPECIFICATION FOR MINERAL FILLER FOR BITUMINOUS PAVING MIXTURES |
| ASTM D 3089 : 1997 : R2008 | Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes |
| ASTM D 242/D242M : 2009 : R2014 | Standard Specification for Mineral Filler For Bituminous Paving Mixtures |
| ASTM C 1097 : 2013 : REDLINE | Standard Specification for Hydrated Lime for Use in Asphalt Cement or Bituminous Paving Mixtures |
| ASTM D 4215 : 2007 : R2013 | Standard Specification for Cold-Mixed, Cold-Laid Bituminous Paving Mixtures |
| AASHTO M 17 : 2011(R2015) | SPECIFICATION FOR MINERAL FILLER FOR BITUMINOUS PAVING MIXTURES |
| AWWA C203 : 2015 | COAL-TAR PROTECTIVE COATINGS AND LININGS FOR STEEL WATER PIPE |
| NACE RP0276:1976 | EXTRUDED ASPHALT MASTIC TYPE PROTECTIVE COATINGS FOR UNDERGROUND PIPELINES |
| ASTM D 242/D242M : 2009 | Standard Specification for Mineral Filler For Bituminous Paving Mixtures |
| ASTM D 3515 : 2001 | Standard Specification for Hot-Mixed, Hot-Laid Bituminous Paving Mixtures (Withdrawn 2009) |
| ASTM D 4215 : 2007 | Standard Specification for Cold-Mixed, Cold-Laid Bituminous Paving Mixtures |
| ASTM D 242 : 2004 | Standard Specification for Mineral Filler For Bituminous Paving Mixtures |
| ASTM D 422 : 1963 : R2002 : EDT 1 | Standard Test Method for Particle-Size Analysis of Soils |
| ASTM D 242 : 2004 | Standard Specification for Mineral Filler For Bituminous Paving Mixtures |
| ASTM C 702 : 1998 | Standard Practice for Reducing Samples of Aggregate to Testing Size |
| ASTM E 11 : 2017 : REDLINE | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM D 4753 : 2015 : REDLINE | Standard Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing |
| ASTM C 786 : 1996 | Standard Test Method for Fineness of Hydraulic Cement and Raw Materials by the 300-µm (No. 50), 150-µm (No. 100), and 75-µm (No. 200) Sieves by Wet Methods |
| ASTM C 670 : 2015 : REDLINE | Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.