ASTM D 5365 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Long-Term Ring-Bending Strain of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
Hardcopy , PDF
17-07-2023
English
21-08-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.1.1 This test method covers a procedure for determining thelong-term ring-bending strain (Sb) of “fiberglass” pipe. Bothglass-fiber-reinforced thermosetting-resin pipe (RTRP) andglass-fiber-reinforced polymer mortar pipe (RPMP) are “fiberglass”pipes.1.2 The values stated in inch-pound units are to be regardedas the standard. The SI units given in parentheses are forinformation only.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appropriatesafety, health, and environmental practices and determinethe applicability of regulatory limitations prior to use. Aspecific warning statement is given in 9.51.4 This international standard was developed in accordancewith internationally recognized principles on standardizationestablished in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendationsissued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.
| Committee |
D 20
|
| DocumentType |
Test Method
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers a procedure for determining the long-term ring-bending strain (Sb) of “fiberglass” pipe. Both glass-fiber-reinforced thermosetting-resin pipe (RTRP) and glass-fiber-reinforced polymer mortar pipe (RPMP) are “fiberglass” pipes.
1.2The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. A specific warning statement is given in 9.5.
Note 1:There is no known ISO equivalent to this standard.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 883 : 2022 | Standard Terminology Relating to Plastics |
| ASTM D 3567 : 1997 : R2006 | Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
| ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 3567 : 2017 : R2022 | Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 3567 : 1997 : R2002 | Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 3567 : 1997 | Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
| ASTM D 3567 : 2017 | Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
| ASTM D 3567 : 1997 : R2011 | Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.