ASTM D 5312/D5312M : 2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Evaluation of Durability of Rock for Erosion Control Under Freezing and Thawing Conditions
Hardcopy , PDF
19-09-2020
English
01-07-2012
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 04.08, 2018 Specifies the procedures for evaluating the durability of rock for erosion control when exposed to freezing and thawing conditions on slabs of rock.
| Committee |
D 18
|
| DevelopmentNote |
Supersedes ASTM D 5312. (02/2013)
|
| DocumentType |
Test Method
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the procedures for evaluating the durability of rock for erosion control when exposed to freezing and thawing conditions on slabs of rock. This weathering test exposes the rock to freezing and thawing cycles similar to natural weather conditions. The rock slabs, prepared in accordance with procedures in Practice D5121, are intended to be representative of erosion control rock and its weaknesses. The test is appropriate for breakwater stone, armor stone, riprap, and gabion sized rock materials.
The limitations of the test are twofold. First the size of the cut rock slab specimens may eliminate some of the internal defects present in the rock structure. The test specimens may not be representative of the quality of the larger rock samples used in construction. Careful examination of the rock source and proper sampling are essential in minimizing this limitation. Secondly the test requires the rock slabs to be exposed to up to 55 freezing-thawing cycles. The test is time intensive and may require up to two or more months to complete the sample preparation, testing, and analysis portions of the procedure.
1.3Units—The values stated in either SI units or inch-pound units [presented in brackets] are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026, unless superseded by this standard.
1.4.1For purposes of comparing measured or calculated value(s) with specified limits, the measured or calculated value(s) shall be rounded to the nearest decimal or significant digits in the specified limits.
1.4.2The procedures used to specify how data are collected/recorded or calculated, in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analytical methods for engineering design.
| ASTM D 5121 : 2015 : REDLINE | Standard Practice for Preparation of Rock Slabs for Durability Testing |
| ASTM D 3740 : 2012-06 | PRACTICE FOR MINIMUM REQUIREMENTS FOR AGENCIES ENGAGED IN TESTING AND/OR INSPECTION OF SOIL AND ROCK AS USED IN ENGINEERING DESIGN AND CONSTRUCTION |
| ASTM D 4753 : 2015 : REDLINE | Standard Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing |
| ASTM D 6026 : 2013 : REDLINE | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 653 : 2014 : REDLINE | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.