ASTM D 5262 :2007
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Evaluating the Unconfined Tension Creep and Creep Rupture Behavior of Geosynthetics
Hardcopy , PDF
11-11-2014
English
01-06-2007
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 04.13, 2017 Specifies the unconfined tension creep and creep rupture behavior of geosynthetics at constant temperature when subjected to a sustained tensile loading.
| Committee |
D 35
|
| DocumentType |
Test Method
|
| Pages |
16
|
| ProductNote |
Reconfirmed 2007
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This test method is intended for use in determining the unconfined tension creep and creep rupture behavior of geosynthetics at constant temperature when subjected to a sustained tensile loading. This test method is applicable to all geosynthetics.
1.2 The test method measures total elongation of the geosynthetic test specimen, from the time of loading, while being maintained at a constant temperature. It includes procedures for measuring the tension creep and creep rupture behavior at constant temperature of conditioned geosynthetics as well as directions for calculating tension creep and creep rupture curves.
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 7406 : 2007 : R2012 | Standard Test Method for Time-Dependent (Creep) Deformation Under Constant Pressure for Geosynthetic Drainage Products |
| ASTM D 6992 : 2016 | Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method |
| ASTM D 7361 : 2007 : R2018 | Standard Test Method for Accelerated Compressive Creep of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method |
| ASTM D 6455 : 2011 : R2018 | Standard Guide for the Selection of Test Methods for Prefabricated Bituminous Geomembranes (PBGMs) |
| ASTM D 5819 : 2018 | Standard Guide for Selecting Test Methods for Experimental Evaluation of Geosynthetic Durability |
| ASTM D 7737/D7737M : 2015 | Standard Test Method for Individual Geogrid Junction Strength |
| ASTM D 8105 : 2018 | Standard Guide for Use and Application of Geosynthetic Reinforcement Reduction Factor Test Results |
| ASTM D 6637/D6637M : 2015 | Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method |
| ASTM E 2777 : 2014 | Standard Guide for Vegetative (Green) Roof Systems |
| ASTM D 4354 : 2012 : REDLINE | Standard Practice for Sampling of Geosynthetics and Rolled Erosion Control Products(RECPs) for Testing |
| ASTM D 4439 : 2017-08 | TERMINOLOGY FOR GEOSYNTHETICS |
| ASTM D 2990 : 2017 : REDLINE | Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics |
| ASTM D 4595 : 2017 : REDLINE | Standard Test Method for Tensile Properties of Geotextiles by the Wide-Width Strip Method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.