ASTM D 5249 : 2010 : R2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Backer Material for Use with Cold- and Hot-Applied Joint Sealants in Portland-Cement Concrete and Asphalt Joints
Hardcopy , PDF
18-05-2021
English
16-03-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 04.03, 2016 Specifies backer material for cold- and hot-applied joint sealant for use in portland-cement concrete or asphalt-pavement joints.
| Committee |
D 04
|
| DocumentType |
Standard
|
| Pages |
4
|
| ProductNote |
Reconfirmed 2016
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers backer material for cold- and hot-applied joint sealant for use in portland-cement concrete or asphalt-pavement joints.
1.2This specification establishes basic requirements for sealant-backer material either in rod or strip form, that can withstand the temperature of hot- or cold-applied sealants without excessive deformation.
1.3Sealant backer material serves one or more of the following purposes:
1.3.1Limits the amount and depth of sealant applied to a joint,
1.3.2Acts as a barrier interface to prevent backside adhesion (bondbreaker), and
1.3.3Provides a form to assist the sealant in developing a shape factor.
1.4The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information purposes only.
1.5The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 7116 : 2016 | Standard Specification for Joint Sealants, Hot Applied, Jet Fuel Resistant Types, for Portland Cement Concrete Pavements |
| ASTM D 6297 : 2013 | Standard Specification for Asphaltic Plug Joints for Bridges |
| ASTM D 6690 : 2015 | Standard Specification for Joint and Crack Sealants, Hot Applied, for Concrete and Asphalt Pavements |
| ASTM D 8139 : 2017 | Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction |
| ASTM D 5893/D5893M : 2016 | Standard Specification for Cold Applied, Single Component, Chemically Curing Silicone Joint Sealant for Portland Cement Concrete Pavements |
| ASTM C 1330 : 2018 | Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid-Applied Sealants |
| ASTM D 6297 : 2020 | Standard Specification for Asphaltic Plug Joints for Bridges |
| ASTM E 1 : 2014 : REDLINE | Standard Specification for ASTM Liquid-in-Glass Thermometers |
| ASTM C 1016 : 2014 : REDLINE | Standard Test Method for Determination of Water Absorption of Sealant Backing<brk/> (Joint Filler) Material |
| ASTM C 1016 : 2002 | Standard Test Method for Determination of Water Absorption of Sealant Backing (Joint Filler) Material |
| ASTM C 1253 : 1993 : R1998 | Standard Test Method for Determining the Outgassing Potential of Sealant Backing |
| ASTM C 1253 : 2014 | Standard Test Method for Determining the Outgassing Potential of Sealant Backing |
| ASTM D 1623 : 2017 : REDLINE | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics |
| ASTM C 1253 : 2014 : R2019 | Standard Test Method for Determining the Outgassing Potential of Sealant Backing |
| ASTM D 1622 : 2008 | Standard Test Method for Apparent Density of Rigid Cellular Plastics |
| ASTM C 1016 : 2002 : R2008 | Standard Test Method for Determination of Water Absorption of Sealant Backing<br> (Joint Filler) Material |
| ASTM C 1253 : 1993 : R2009 | Standard Test Method for Determining the Outgassing Potential of Sealant Backing |
| ASTM D 1623 : 2003 | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics |
| ASTM D 1622 : 2003 | Standard Test Method for Apparent Density of Rigid Cellular Plastics |
| ASTM D 545 : 2014 : REDLINE | Standard Test Methods for Preformed Expansion Joint Fillers for Concrete Construction (Nonextruding and Resilient Types) |
| ASTM C 1016 : 2014 | Standard Test Method for Determination of Water Absorption of Sealant Backing<brk/> (Joint Filler) Material |
| ASTM D 5535 : 1998 | Standard Terminology Relating to Formed-in-Place Sealants for Joints and Cracks in Pavements |
| ASTM D 1623 : 2009 | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics |
| ASTM D 1622 : 1998 | Standard Test Method for Apparent Density of Rigid Cellular Plastics |
| ASTM D 5535 : 1998 : R2003 | Standard Terminology Relating to Formed-in-Place Sealants for Joints and Cracks in Pavements (Withdrawn 2009) |
| ASTM D 1623 : 1978 : R1995 | Standard Test Method for Tensile And Tensile Adhesion Properties Of Rigid Cellular Plastics |
| ASTM C 1016 : 2002 : R2008 : EDT 1 | Standard Test Method for Determination of Water Absorption of Sealant Backing<br> (Joint Filler) Material |
| ASTM E 220 : 2013 : REDLINE | Standard Test Method for Calibration of Thermocouples By Comparison Techniques |
| ASTM C 1016 : 1994 : REV A | Standard Test Method for Determination of Water Absorption of Sealant Backing (Joint Filler) Material |
| ASTM D 1623 : 2017 | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics |
| ASTM C 670 : 2015 : REDLINE | Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials |
| ASTM C 1253 : 1993 : R2005 | Standard Test Method for Determining the Outgassing Potential of Sealant Backing |
| ASTM D 1622 : 1993 | Standard Test Method for Apparent Density of Rigid Cellular Plastics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.