Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 4950 : 2019

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Classification and Specification for Automotive Service Greases

Available format(s)

Hardcopy , PDF

Superseded date

27-01-2023

Superseded by

ASTM D 4950 : 2022

Language(s)

English

Published date

20-11-2019

$122.77
Including GST where applicable

Committee
D 02
DocumentType
Standard
Pages
6
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This specification covers lubricating greases suitable for the periodic relubrication of chassis systems and wheel bearings of passenger cars, trucks, and other vehicles.

1.2This specification defines the requirements used to describe the properties and performance characteristics of chassis greases and wheel bearing greases for service-fill applications.

1.3The test requirements (acceptance limits) given in this specification are, as the case may be, minimum or maximum acceptable values for valid duplicate test results. Apply no additional corrections for test precision, such as described in Practice D3244, inasmuch as the precision of the test methods was taken into account in the determination of the requirements.

1.4The values stated in SI units are to be regarded as standard.

1.4.1Exceptions—Test Method D2596 reports test results in kgf units, and Test Method D4289 reports rubber hardness in Durometer Shore A units.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM C 1812/C1812M : 2022 Standard Practice for Design of Journal Bearing Supports to be Used in Fiber Reinforced Concrete Beam Tests
ASTM C 1812/C1812M : 2015 : EDT 1 Standard Practice for Design of Journal Bearing Supports to be Used in Fiber Reinforced Concrete Beam Tests
ASTM D 4289 : 2013 : R2014 : EDT 1 Standard Test Method for Elastomer Compatibility of Lubricating Greases and Fluids
ASTM D 6185 : 2011 : R2017 Standard Practice for Evaluating Compatibility of Binary Mixtures of Lubricating Greases

ASTM D 4175 : 2020 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 3244 : 2018 Standard Practice for Utilization of Test Data to Determine Conformance with Specifications
ASTM D 4693 : 1997 Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings
ASTM D 4693 : 2007 : R2017 Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings
ASTM D 3527 : 2018 Standard Test Method for Life Performance of Automotive Wheel Bearing Grease
ASTM D 217 : 2021 Standard Test Methods for Cone Penetration of Lubricating Grease
ASTM D 2596 : 2020 Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Grease (Four-Ball Method)
ASTM D 3244 : 1997 Standard Practice for Utilization of Test Data to Determine Conformance with Specifications
ASTM D 4175 : 2020 : REV B Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4289 : 2019 Standard Test Method for Elastomer Compatibility of Lubricating Greases and Fluids
ASTM D 4175 : 2020 : REV A Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 2596 : 1997 Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Grease (Four-Ball Method)
ASTM D 4175 : 2022 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4693 : 2007 : R2021 Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings
ASTM D 217 : 2021 : REV A Standard Test Methods for Cone Penetration of Lubricating Grease
ASTM D 1742 : 2020 Standard Test Method for Oil Separation from Lubricating Grease During Storage
ASTM D 3244 : 2021 : REV A Standard Practice for Utilization of Test Data to Determine Conformance with Specifications
ASTM D 4175 : 2001 : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2020 : REV B : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4170 : 1997 Standard Test Method for Fretting Wear Protection by Lubricating Greases
ASTM D 4175 : 2022 : REV A Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2002 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 217 : 2019 : REV B Standard Test Methods for Cone Penetration of Lubricating Grease
ASTM D 2265 : 2020 Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range
ASTM D 3244 : 2020 Standard Practice for Utilization of Test Data to Determine Conformance with Specifications
ASTM D 1743 : 2021 Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases
ASTM D 217 : 1997 Standard Test Methods for Cone Penetration of Lubricating Grease
ASTM D 1743 : 2022 Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases
ASTM D 2265 : 2022 Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range
ASTM D 2596 : 2015 Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Grease (Four-Ball Method)
ASTM D 1264 : 2018 : EDT 1 Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases
ASTM D 4175 : 2022 : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 2265 : 2019 Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range
ASTM D 3527 : 2021 Standard Test Method for Life Performance of Automotive Wheel Bearing Grease
ASTM D 4290 : 2020 Standard Test Method for Determining the Leakage Tendencies of Automotive Wheel Bearing Grease Under Accelerated Conditions
ASTM D 3244 : 2021 Standard Practice for Utilization of Test Data to Determine Conformance with Specifications
ASTM D 4289 : 2021 Standard Test Method for Elastomer Compatibility of Lubricating Greases and Fluids
ASTM D 2265 : 1994 : REV A Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range
ASTM D 1742 : 2018 Standard Test Method for Oil Separation from Lubricating Grease During Storage
ASTM D 1743 : 2013 : R2018 Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases
ASTM D 1264 : 2018 Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases
ASTM D 4290 : 2019 Standard Test Method for Determining the Leakage Tendencies of Automotive Wheel Bearing Grease Under Accelerated Conditions

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more