ASTM D 4950 : 2014
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Classification and Specification for Automotive Service Greases
Available format(s)
Hardcopy , PDF
Superseded date
20-11-2019
Superseded by
Language(s)
English
Published date
01-12-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.1.1 This specification covers lubricating greases suitable for the periodic relubrication of chassis systems and wheel bearings of passenger cars, trucks, and other vehicles.
| Committee |
D 02
|
| DocumentType |
Standard
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers lubricating greases suitable for the periodic relubrication of chassis systems and wheel bearings of passenger cars, trucks, and other vehicles.
1.2This specification defines the requirements used to describe the properties and performance characteristics of chassis greases and wheel bearing greases for service-fill applications.
1.3The test requirements (acceptance limits) given in this specification are, as the case may be, minimum or maximum acceptable values for valid duplicate test results. Apply no additional corrections for test precision, such as described in Practice D3244, inasmuch as the precision of the test methods was taken into account in the determination of the requirements.
1.4The values stated in SI units are to be regarded as standard.
1.4.1Exceptions—Test Method D2596 reports test results in kgf units, and Test Method D4289 reports rubber hardness in Durometer Shore A units.
| ASTM D 4289 : 2013 : R2014 : EDT 1 | Standard Test Method for Elastomer Compatibility of Lubricating Greases and Fluids |
| ASTM D 6185 : 2011 : R2017 | Standard Practice for Evaluating Compatibility of Binary Mixtures of Lubricating Greases |
| ASTM C 1812/C1812M : 2015 : EDT 1 | Standard Practice for Design of Journal Bearing Supports to be Used in Fiber Reinforced Concrete Beam Tests |
| ASTM D 2266 : 2001 | Standard Test Method for Wear Preventive Characteristics of Lubricating Grease (Four-Ball Method) |
| ASTM D 4175 : 2014 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2009 : REV A : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2008 : REV B : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4693 : 1997 | Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings |
| ASTM D 4175 : 2005 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2005 : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4693 : 2007 : R2017 | Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings |
| ASTM D 3527 : 2018 | Standard Test Method for Life Performance of Automotive Wheel Bearing Grease |
| ASTM D 3244 : 1997 | Standard Practice for Utilization of Test Data to Determine Conformance with Specifications |
| ASTM D 1742 : 2006 : R2013 | Standard Test Method for Oil Separation from Lubricating Grease During Storage |
| ASTM D 4175 : 2015 : REV C | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 3244 : 2012 | Standard Practice for Utilization of Test Data to Determine Conformance with Specifications |
| ASTM D 4175 : 2017 : REV A : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 2266 : 2001 : R2015 | Standard Test Method for Wear Preventive Characteristics of Lubricating Grease (Four-Ball Method) |
| ASTM D 4170 : 2010 | Standard Test Method for Fretting Wear Protection by Lubricating Greases |
| ASTM D 4175 : 2008 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 3527 : 1995 | Standard Test Method for Life Performance of Automotive Wheel Bearing Grease |
| ASTM D 4175 : 2017 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 1742 : 1994 : R2000 : EDT 1 | Standard Test Method for Oil Separation from Lubricating Grease During Storage |
| ASTM D 4175 : 2009 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 2596 : 1997 | Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Grease (Four-Ball Method) |
| ASTM D 4290 : 2007 | Standard Test Method for Determining the Leakage Tendencies of Automotive Wheel Bearing Grease Under Accelerated Conditions |
| ASTM D 2596 : 2010 : EDT 1 | Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Grease (Four-Ball Method) |
| ASTM D 3244 : 2007 | Standard Practice for Utilization of Test Data to Determine Conformance with Specifications |
| ASTM D 1264 : 2016 | Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases |
| ASTM D 1743 : 2005 : REV A | Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases |
| ASTM D 4289 : 2003 | Standard Test Method for Elastomer Compatibility of Lubricating Greases and Fluids |
| ASTM D 3244 : 2016 | Standard Practice for Utilization of Test Data to Determine Conformance with Specifications |
| ASTM D 4175 : 2009 : REV A : EDT 4 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2009 : REV A : EDT 3 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 3527 : 2002 | Standard Test Method for Life Performance of Automotive Wheel Bearing Grease |
| ASTM D 4175 : 2018 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 3527 : 2007 | Standard Test Method for Life Performance of Automotive Wheel Bearing Grease |
| ASTM D 4175 : 2001 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4170 : 1997 | Standard Test Method for Fretting Wear Protection by Lubricating Greases |
| ASTM D 4175 : 2001 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2005 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 1264 : 2003 : EDT 1 | Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases |
| ASTM D 1264 : 2011 | Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases |
| ASTM D 4290 : 1994 : R1999 | Standard Test Method for Determining the Leakage Tendencies of Automotive Wheel Bearing Grease Under Accelerated Conditions |
| ASTM D 2266 : 2001 : R2008 | Standard Test Method for Wear Preventive Characteristics of Lubricating Grease (Four-Ball Method) |
| ASTM D 4175 : 2002 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4290 : 2015 | Standard Test Method for Determining the Leakage Tendencies of Automotive Wheel Bearing Grease Under Accelerated Conditions |
| ASTM D 4175 : 2015 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2002 : REV A : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4170 : 2016 | Standard Test Method for Fretting Wear Protection by Lubricating Greases |
| ASTM D 1264 : 2000 | Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases |
| ASTM D 1743 : 2005 | Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases |
| ASTM D 4290 : 2007 : R2012 | Standard Test Method for Determining the Leakage Tendencies of Automotive Wheel Bearing Grease Under Accelerated Conditions |
| ASTM D 1264 : 2012 | Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases |
| ASTM D 2265 : 2006 : R2014 | Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range |
| ASTM D 4175 : 2009 : REV A : EDT 5 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2016 : REV C | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2015 : REV B | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4289 : 1997 | Standard Test Method for Elastomer Compatibility of Lubricating Greases and Fluids |
| ASTM D 4289 : 2013 | Standard Test Method for Elastomer Compatibility of Lubricating Greases and Fluids |
| ASTM D 2265 : 2015 : EDT 1 | Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range |
| ASTM D 4175 : 2015 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2009 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2016 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 3527 : 2007 : EDT 1 | Standard Test Method for Life Performance of Automotive Wheel Bearing Grease |
| ASTM D 4175 : 2002 : REV A : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2008 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2002 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 1742 : 2006 | Standard Test Method for Oil Separation from Lubricating Grease During Storage |
| ASTM D 2596 : 2015 | Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Grease (Four-Ball Method) |
| ASTM D 4175 : 2000 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2016 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 1743 : 2010 | Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases |
| ASTM D 4693 : 2007 | Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings |
| ASTM D 1264 : 2003 | Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases |
| ASTM D 1264 : 2003 : R2008 | Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases |
| ASTM D 2265 : 2019 | Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range |
| ASTM D 1743 : 2013 | Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases |
| ASTM D 1743 : 2001 | Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases |
| ASTM D 2265 : 2006 | Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range |
| ASTM D 4175 : 2017 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 2265 : 2000 | Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range |
| ASTM D 1743 : 2005 : REV A : EDT 1 | Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases |
| ASTM D 4175 : 2009 : REV A : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 3527 : 2015 | Standard Test Method for Life Performance of Automotive Wheel Bearing Grease |
| ASTM D 1264 : 1996 | Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases |
| ASTM D 3527 : 2011 | Standard Test Method for Life Performance of Automotive Wheel Bearing Grease |
| ASTM D 4290 : 2002 | Standard Test Method for Determining the Leakage Tendencies of Automotive Wheel Bearing Grease Under Accelerated Conditions |
| ASTM D 4175 : 2018 : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2016 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 2265 : 1994 : REV A | Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range |
| ASTM D 1743 : 1994 : EDT 1 | Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases |
| ASTM D 1743 : 2013 : R2018 | Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases |
| ASTM D 4693 : 2003 | Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings |
| ASTM D 4693 : 2007 : R2012 | Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings |
| ASTM D 1264 : 2018 | Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases |
| ASTM D 2596 : 2010 | Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Grease (Four-Ball Method) |
| ASTM D 4175 : 2017 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 2266 : 1991 : R1996 | Standard Test Method for Wear Preventive Characteristics of Lubricating Grease (Four-Ball Method) |
| ASTM D 4175 : 2019 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 3244 : 2007 : REV A | Standard Practice for Utilization of Test Data to Determine Conformance with Specifications |
| ASTM D 4175 : 2015 : REV B : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4289 : 2013 : R2014 : EDT 1 | Standard Test Method for Elastomer Compatibility of Lubricating Greases and Fluids |
| ASTM D 4290 : 2019 | Standard Test Method for Determining the Leakage Tendencies of Automotive Wheel Bearing Grease Under Accelerated Conditions |
| ASTM D 4175 : 2008 : REV B | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4289 : 2003 : R2008 | Standard Test Method for Elastomer Compatibility of Lubricating Greases and Fluids |
| ASTM D 2265 : 2015 | Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range |
| ASTM D 2596 : 2014 | Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Grease (Four-Ball Method) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.