ASTM D 445 : 2021 : EDT 2
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
Hardcopy , PDF
17-04-2024
English
19-10-2022
Committee |
D 02
|
DocumentType |
Test Method
|
Pages |
17
|
ProductNote |
ε2NOTE—Editorially removed joint designation in October 2022
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method specifies a procedure for the determination of the kinematic viscosity, ν, of liquid petroleum products, both transparent and opaque, by measuring the time for a volume of liquid to flow under gravity through a calibrated glass capillary viscometer. The dynamic viscosity, η, can be obtained by multiplying the kinematic viscosity, ν, by the density, ρ, of the liquid.
Note 1:For the measurement of the kinematic viscosity and viscosity of bitumens, see also Test Methods D2170 and D2171.
Note 2:ISO 3104 corresponds to Test Method D445 – 03.
1.2The result obtained from this test method is dependent upon the behavior of the sample and is intended for application to liquids for which primarily the shear stress and shear rates are proportional (Newtonian flow behavior). If, however, the viscosity varies significantly with the rate of shear, different results may be obtained from viscometers of different capillary diameters. The procedure and precision values for residual fuel oils, which under some conditions exhibit non-Newtonian behavior, have been included.
1.3The range of kinematic viscosities covered by this test method is from 0.2 mm2/s to 300 000 mm2/s (see Table A1.1) at all temperatures (see 6.3 and 6.4). The precision has only been determined for those materials, kinematic viscosity ranges and temperatures as shown in the footnotes to the precision section.
1.4The values stated in SI units are to be regarded as standard. The SI unit used in this test method for kinematic viscosity is mm2/s, and the SI unit used in this test method for dynamic viscosity is mPa·s. For user reference, 1 mm2/s = 10-6 m2/s = 1 cSt and 1 mPa·s = 1 cP = 0.001 Pa·s.
1.5WARNING—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use Caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 8256 : 2023 | Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in the Sequence VH Spark-Ignition Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions |
ASTM D 6448 : 2016 : R2022 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
ASTM D 2532 : 2022 | Standard Test Method for Viscosity and Viscosity Change After Standing at Low Temperature of Aircraft Turbine Lubricants |
ASTM D 8111 : 2023 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIH, Spark-Ignition Engine |
ASTM D 5900 : 2023 | Standard Specification for Physical and Chemical Properties of Industry Reference Materials (IRM) |
ASTM E 2412 : 2023 | Standard Practice for Condition Monitoring of In-Service Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 7826 : 2023 : REV A | Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives |
ASTM D 1655 : 2023 : REV A | Standard Specification for Aviation Turbine Fuels |
ASTM D 5222 : 2023 | Standard Specification for Less Flammable High Molecular Weight Hydrocarbon Mineral Electrical Insulating Liquids |
ASTM D 8092 : 2022 | Standard Test Method for Field Determination of Kinematic Viscosity Using a Microchannel Viscometer |
ASTM D 4174 : 2023 | Standard Practice for Cleaning, Flushing, and Purification of Petroleum Fluid Hydraulic Systems |
ASTM D 6751 : 2023 : REV A | Standard Specification for Biodiesel Fuel Blendstock (B100) for Middle Distillate Fuels |
ASTM D 8279 : 2023 : REV A | Standard Test Method for Determination of Timing-Chain Wear in a Turbocharged, Direct-Injection, Spark-Ignition, Four-Cylinder Engine |
ASTM D 6439 : 2023 | Standard Guide for Cleaning, Flushing, and Purification of Steam, Gas, and Hydroelectric Turbine Lubrication Systems |
ASTM D 4878 : 2023 | Standard Test Methods for Polyurethane Raw Materials: Determination of Viscosity of Polyols |
ASTM D 4283 : 1998 : R2022 | Standard Test Method for Viscosity of Silicone Fluids |
ASTM D 7596 : 2023 | Standard Test Method for Automatic Particle Counting and Particle Shape Classification of Oils Using a Direct Imaging Integrated Tester |
ASTM D 6750 : 2023 | Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur) |
ASTM D 8047 : 2023 | Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine |
ASTM D 6891 : 2023 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IVA Spark-Ignition Engine |
ASTM D 5763 : 2022 : REV A | Standard Test Method for Oxidation and Thermal Stability Characteristics of Gear Oils Using Universal Glassware |
ASTM F 715 : 2007 : R2023 | Standard Test Methods for Coated Fabrics Used for Oil Spill Control and Storage |
ASTM D 975 : 2023 | Standard Specification for Diesel Fuel |
ASTM D 4304 : 2022 | Standard Specification for Mineral and Synthetic Lubricating Oil Used in Steam or Gas Turbines |
ASTM D 6074 : 2015 : R2022 | Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils |
ASTM D 892 : 2023 | Standard Test Method for Foaming Characteristics of Lubricating Oils |
ASTM D 8147 : 2017 : R2023 | Standard Specification for Special-Purpose Test Fuels for Aviation Compression-Ignition Engines |
ASTM D 4054 : 2023 | Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives |
ASTM D 2170/D2170M : 2022 | Standard Test Method for Kinematic Viscosity of Asphalts |
ASTM D 7583 : 2016 : R2023 | Standard Test Method for John Deere Coolant Cavitation Test |
ASTM D 8506 : 2023 | Standard Guide for Microbial Contamination and Biodeterioration in Turbine Oils and Turbine Oil Systems |
ASTM D 7467 : 2023 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 8240 : 2022 : EDT 1 | Standard Specification for Less-Flammable Synthetic Ester Liquids Used in Electrical Apparatus |
ASTM D 1243 : 2022 : EDT 1 | Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride Polymers |
ASTM D 2880 : 2023 | Standard Specification for Gas Turbine Fuel Oils |
ASTM D 8180 : 2023 | Standard Specification for Rerefined Mineral Insulating Liquid Used in Electrical Apparatus |
ASTM D 8114 : 2023 : REV A | Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIE Spark Ignition |
ASTM D 7152 : 2023 | Standard Practice for Calculating Viscosity of a Blend of Petroleum Products |
ASTM D 7549 : 2023 | Standard Test Method for Evaluation of Heavy-Duty Engine Oils under High Output Conditions—Caterpillar C13 Test Procedure |
ASTM D 4243 : 2023 | Standard Test Method for Measurement of Average Viscometric Degree of Polymerization of New and Aged Electrical Papers and Boards |
ASTM D 6923 : 2023 | Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1R Test Procedure |
ASTM D 6618 : 2023 | Standard Test Method for Evaluation of Engine Oils in Diesel Four-Stroke Cycle Supercharged 1M-PC Single Cylinder Oil Test Engine |
ASTM D 7109 : 2022 : EDT 1 | Standard Test Method for Shear Stability of Polymer-Containing Fluids Using a European Diesel Injector Apparatus at 30 Cycles and 90 Cycles |
ASTM D 5704 : 2022 : REV A | Standard Test Method for Evaluation of the Thermal and Oxidative Stability of Lubricating Oils Used for Manual Transmissions and Final Drive Axles |
ASTM D 6681 : 2023 | Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1P Test Procedure |
ASTM D 4293 : 2022 | Standard Specification for Phosphate Ester-Based Fluids for Turbine Lubrication and Steam Turbine Electro-Hydraulic Control (EHC) Applications |
ASTM D 7544 : 2023 | Standard Specification for Pyrolysis Liquid Biofuel |
ASTM D 2414 : 2023 | Standard Test Method for Carbon Black—Oil Absorption Number (OAN) |
ASTM D 8350 : 2023 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IVB Spark-Ignition Engine |
ASTM D 7566 : 2023 : REV A | Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons |
ASTM D 7484 : 2023 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils for Valve-Train Wear Performance in Cummins ISB Medium-Duty Diesel Engine |
ASTM D 8074 : 2023 | Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine |
ASTM D 8291 : 2023 : REV A | Standard Test Method for Evaluation of Performance of Automotive Engine Oils in the Mitigation of Low-Speed, Preignition in the Sequence IX Gasoline Turbocharged Direct-Injection, Spark-Ignition Engine |
ASTM D 7109 : 2022 | Standard Test Method for Shear Stability of Polymer-Containing Fluids Using a European Diesel Injector Apparatus at 30 Cycles and 90 Cycles |
ASTM D 4052 : 2022 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM E 3282 : 2022 | Standard Guide for NAPL Mobility and Migration in Sediments – Evaluation Metrics |
ASTM D 1243 : 2022 | Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride Polymers |
ASTM D 7528 : 2022 | Standard Test Method for Bench Oxidation of Engine Oils by ROBO Apparatus |
ASTM D 8128 : 2022 | Standard Guide for Monitoring Failure Mode Progression in Industrial Applications with Rolling Element Ball Type Bearings |
ASTM D 1601 : 2018 | Standard Test Method for Dilute Solution Viscosity of Ethylene Polymers |
ASTM D 4603 : 2018 | Standard Test Method for Determining Inherent Viscosity of Poly(Ethylene Terephthalate) (PET) by Glass Capillary Viscometer |
ASTM D 1569 : 2005 : R2014 | Standard Test Methods for Detergent Alkylate (Withdrawn 2023) |
ASTM D 2140 : 2008 : R2017 | Standard Practice for Calculating Carbon-Type Composition of Insulating Oils of Petroleum Origin |
ASTM D 2270 : 2010 : R2016 | Standard Practice for Calculating Viscosity Index from Kinematic Viscosity at 40 °C and 100 °C |
ASTM D 3607 : 2008 : R2016 | Standard Test Method for Removing Volatile Contaminants from Used Engine Oils by Stripping (Withdrawn 2022) |
ASTM D 4283 : 1998 : R2015 | Standard Test Method for Viscosity of Silicone Fluids |
ASTM D 446 : 2012 : R2017 | Standard Specifications and Operating Instructions for Glass Capillary Kinematic Viscometers |
ASTM D 7544 : 2012 : R2017 | Standard Specification for Pyrolysis Liquid Biofuel |
ASTM D 3487 : 2016 : EDT 1 | Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus |
ASTM D 6439 : 2011 : R2017 | Standard Guide for Cleaning, Flushing, and Purification of Steam, Gas, and Hydroelectric Turbine Lubrication Systems |
ASTM D 4293 : 2015 : EDT 1 | Standard Specification for Phosphate Ester Based Fluids for Turbine Lubrication and Steam Turbine Electro-Hydraulic Control (EHC) Applications |
ASTM D 4682 : 2018 | Standard Specification for Miscibility with Gasoline and Fluidity of Two-Stroke-Cycle Gasoline Engine Lubricants |
ASTM D 6923 : 2018 | Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1R Test Procedure |
ASTM D 2170/D2170M : 2018 | Standard Test Method for Kinematic Viscosity of Asphalts |
ASTM D 4486 : 2018 | Standard Test Method for Kinematic Viscosity of Volatile and Reactive Liquids |
ASTM D 8181 : 2019 | Standard Specification for Microemulsion Blendstock for Preparing Microemulsion Test Fuel Oils |
ASTM E 2412 : 2010 : R2018 | Standard Practice for Condition Monitoring of In-Service Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 2501 : 2014 : R2019 | Standard Test Method for Calculation of Viscosity-Gravity Constant (VGC) of Petroleum Oils |
ASTM D 7973 : 2019 | Standard Guide for Monitoring Failure Mode Progression in Plain Bearings |
ASTM D 3699 : 2019 | Standard Specification for Kerosine |
ASTM D 2893 : 2019 | Standard Test Methods for Oxidation Characteristics of Extreme-Pressure Lubrication Oils |
ASTM D 7156 : 2019 | Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine |
ASTM D 2502 : 2014 : R2019 : EDT 1 | Standard Test Method for Estimation of Mean Relative Molecular Mass of Petroleum Oils from Viscosity Measurements |
ASTM D 6514 : 2003 : R2019 : EDT 1 | Standard Test Method for High Temperature Universal Oxidation Test for Turbine Oils |
ASTM D 7152 : 2011 : R2016 : EDT 1 | Standard Practice for Calculating Viscosity of a Blend of Petroleum Products |
ASTM D 5621 : 2020 | Standard Test Method for Sonic Shear Stability of Hydraulic Fluids |
ASTM D 2603 : 2020 | Standard Test Method for Sonic Shear Stability of Polymer-Containing Oils |
ASTM D 892 : 2018 | Standard Test Method for Foaming Characteristics of Lubricating Oils |
ASTM D 5275 : 2020 | Standard Test Method for Fuel Injector Shear Stability Test (FISST) for Polymer Containing Fluids |
ASTM F 631 : 2015 : R2020 | Standard Guide for Collecting Skimmer Performance Data in Controlled Environments |
ASTM D 7887 : 2020 | Standard Guide for Selection of Substitute, Non-hazardous, Liquid Filling Substances for Packagings Subjected to the United Nations Performance Tests |
ASTM D 6666 : 2020 | Standard Guide for Evaluation of Aqueous Polymer Quenchants |
ASTM D 7416 : 2009 : R2020 | Standard Practice for Analysis of In-Service Lubricants Using a Particular Five-Part (Dielectric Permittivity, Time-Resolved Dielectric Permittivity with Switching Magnetic Fields, Laser Particle Counter, Microscopic Debris Analysis, and Orbital Viscometer) Integrated Tester |
ASTM D 341 : 2020 : EDT 1 | Standard Practice for Viscosity-Temperature Equations and Charts for Liquid Petroleum or Hydrocarbon Products |
ASTM D 7155 : 2020 | Standard Practice for Evaluating Compatibility of Mixtures of Turbine Lubricating Oils |
ASTM D 7578 : 2020 | Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants |
ASTM D 7666 : 2012 : R2019 | Standard Specification for Triglyceride Burner Fuel |
ASTM F 715 : 2007 : R2018 | Standard Test Methods for Coated Fabrics Used for Oil Spill Control and Storage |
ASTM F 2084/F2084M : 2001 : R2018 | Standard Guide for Collecting Containment Boom Performance Data in Controlled Environments |
ASTM D 8029 : 2018 | Standard Specification for Biodegradable, Low Aquatic Toxicity Hydraulic Fluids |
ASTM D 4504 : 1994 : R2018 | Standard Specification for Molded Polyethylene Open-Head-Pails for Industrial Shipping of Nonhazardous Goods |
ASTM D 6158 : 2018 | Standard Specification for Mineral Hydraulic Oils |
ASTM D 6080 : 2018 : REV A | Standard Practice for Defining the Viscosity Characteristics of Hydraulic Fluids |
ASTM F 3208 : 2020 | Standard Guide for Selecting Test Soils for Validation of Cleaning Methods for Reusable Medical Devices |
ASTM D 4040 : 2010 : R2019 | Standard Test Method for Rheological Properties of Paste Printing and Vehicles by the Falling-Rod Viscometer |
ASTM D 128 : 1998 : R2019 | Standard Test Methods for Analysis of Lubricating Grease |
ASTM D 7467 : 2020 : REV A | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 6278 : 2020 : REV A | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
ASTM D 4731 : 2013 : R2020 | Standard Specification for Hot-Application Filling Compounds for Telecommunications Wire and Cable |
ASTM D 4732 : 2013 : R2020 | Standard Specification for Cool-Application Filling Compounds for Telecommunications Wire and Cable |
ASTM D 6469 : 2020 | Standard Guide for Microbial Contamination in Fuels and Fuel Systems |
ASTM D 6751 : 2020 : REV A | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 8278 : 2020 | Standard Specification for Digital Contact Thermometers for Test Methods Measuring Flow Properties of Fuels and Lubricants |
ASTM D 5372 : 2020 | Standard Guide for Evaluation of Hydrocarbon Heat Transfer Fluids |
ASTM D 8274 : 2020 : REV A | Standard Test Method for Determination of Biodiesel (Fatty Acid Methyl Esters) Content in Diesel Fuel Oil by Portable Rapid Mid-Infrared Analyzer |
ASTM D 2225 : 2020 | Standard Test Methods for Silicone Liquids Used for Electrical Insulation |
ASTM D 4652 : 2020 | Standard Specification for Silicone Liquid Used for Electrical Insulation |
ASTM D 5282 : 2005 : R2020 | Standard Test Methods for Compatibility of Construction Material with Silicone Fluid Used for Electrical Insulation |
ASTM D 5900 : 2020 | Standard Specification for Physical and Chemical Properties of Industry Reference Materials (IRM) |
ASTM D 7279 : 2020 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids by Automated Houillon Viscometer |
ASTM D 1934 : 2020 | Standard Test Method for Oxidative Aging of Electrical Insulating Liquids by Open-Beaker Method |
ASTM D 7483 : 2021 | Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Oscillating Piston Viscometer |
ASTM F 2161 : 2021 | Standard Guide for Instrument and Precision Bearing Lubricants—Part 1 Oils |
ASTM D 4889 : 2021 | Standard Test Methods for Polyurethane Raw Materials: Determination of Viscosity of Crude or Modified Isocyanates |
ASTM D 2161 : 2020 | Standard Practice for Conversion of Kinematic Viscosity to Saybolt Universal Viscosity or to Saybolt Furol Viscosity |
ASTM D 3236 : 2015 : R2021 | Standard Test Method for Apparent Viscosity of Hot Melt Adhesives and Coating Materials |
ASTM D 2880 : 2020 | Standard Specification for Gas Turbine Fuel Oils |
ASTM D 7549 : 2021 | Standard Test Method for Evaluation of Heavy-Duty Engine Oils under High Output Conditions—Caterpillar C13 Test Procedure |
ASTM D 8164 : 2021 | Standard Guide for Digital Contact Thermometers for Petroleum Products, Liquid Fuels, and Lubricant Testing |
ASTM D 2162 : 2021 | Standard Practice for Basic Calibration of Master Viscometers and Viscosity Oil Standards |
ASTM D 396 : 2021 | Standard Specification for Fuel Oils |
ASTM D 8324 : 2021 | Standard Guide for Selection of Environmentally Acceptable Lubricants for the U.S. Environmental Protection Agency (EPA) Vessel General Permit |
ASTM D 333 : 2001 : R2021 | Standard Guide for Clear and Pigmented Lacquers |
ASTM D 1795 : 2013 : R2021 | Standard Test Method for Intrinsic Viscosity of Cellulose |
ASTM D 471 : 2016 : REV A : R2021 | Standard Test Method for Rubber Property—Effect of Liquids |
ASTM D 1763 : 2000 : R2021 | Standard Specification for Epoxy Resins |
ASTM D 5964 : 2016 : R2021 | Standard Practice for Rubber IRM 901, IRM 902, and IRM 903 Replacement Oils for ASTM No. 1, ASTM No. 2, ASTM No. 3 Oils, and IRM 905 formerly ASTM No. 5 Oil |
ASTM E 709 : 2021 | Standard Guide for Magnetic Particle Testing |
ASTM D 5967 : 2021 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
ASTM D 7720 : 2021 | Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination |
ASTM D 7484 : 2021 : REV B | Standard Test Method for Evaluation of Automotive Engine Oils for Valve-Train Wear Performance in Cummins ISB Medium-Duty Diesel Engine |
ASTM D 7223 : 2021 | Standard Specification for Aviation Certification Turbine Fuel |
ASTM D 6823 : 2008 : R2021 | Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils |
ASTM D 4924 : 2021 | Standard Classification for Petroleum Waxes for Use in Rubber Compounding |
ASTM D 7042 : 2021 : REV A | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
ASTM D 7826 : 2021 | Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives |
ASTM D 6710 : 2021 | Standard Guide for Evaluation of Hydrocarbon-Based Quench Oil |
ASTM D 8046 : 2021 | Standard Guide for Pumpability of Heat Transfer Fluids |
ASTM D 7945 : 2021 : REV A | Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Constant Pressure Viscometer |
ASTM D 8074 : 2022 | Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine |
ASTM D 6224 : 2022 | Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment |
ASTM D 6709 : 2022 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence VIII Spark-Ignition Engine (CLR Oil Test Engine) |
ASTM D 7422 : 2022 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 5966 : 2022 | Standard Test Method for Evaluation of Engine Oils for Roller Follower Wear in Light-Duty Diesel Engine |
ASTM D 8256 : 2022 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in the Sequence VH Spark-Ignition Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions |
ASTM D 5704 : 2022 | Standard Test Method for Evaluation of the Thermal and Oxidative Stability of Lubricating Oils Used for Manual Transmissions and Final Drive Axles |
ASTM D 4871 : 2011 : R2022 | Standard Guide for Universal Oxidation/Thermal Stability Test Apparatus |
ASTM D 4054 : 2022 | Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives |
ASTM D 2857 : 2022 | Standard Practice for Dilute Solution Viscosity of Polymers |
ASTM D 2532 : 2017 | Standard Test Method for Viscosity and Viscosity Change After Standing at Low Temperature of Aircraft Turbine Lubricants |
ASTM D 117 : 2022 | Standard Guide for Sampling, Test Methods, and Specifications for Electrical Insulating Liquids |
ASTM D 8047 : 2019 : EDT 1 | Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine |
ASTM D 7320 : 2018 : EDT 1 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
ASTM D 8048 : 2021 : REV A : EDT 1 | Standard Test Method for Evaluation of Diesel Engine Oils in T-13 Diesel Engine |
ASTM D 6984 : 2018 : EDT 1 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIF, Spark-Ignition Engine |
ASTM D 6593 : 2018 : EDT 1 | Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions |
ASTM D 4057 : 2022 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 6891 : 2021 : EDT 1 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IVA Spark-Ignition Engine |
ASTM D 7589 : 2016 : EDT 1 | Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VID Spark Ignition Engine<rangeref></rangeref > |
ASTM D 6750 : 2019 : EDT 1 | Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur) |
ASTM D 8111 : 2021 : REV A : EDT 1 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIH, Spark-Ignition Engine |
ASTM D 8291 : 2021 : REV A : EDT 1 | Standard Test Method for Evaluation of Performance of Automotive Engine Oils in the Mitigation of Low-Speed, Preignition in the Sequence IX Gasoline Turbocharged Direct-Injection, Spark-Ignition Engine |
ASTM D 2669 : 2016 | Standard Test Method for Apparent Viscosity of Petroleum Waxes Compounded with Additives (Hot Melts) |
ASTM D 8226 : 2021 : REV A : EDT 1 | Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIF Spark Ignition Engine<rangeref></rangeref > |
ASTM D 4142 : 1989 : R2022 | Standard Guide for Testing Epoxy Resins |
ASTM D 7468 : 2022 | Standard Test Method for Cummins ISM Test |
ASTM D 2414 : 2022 | Standard Test Method for Carbon Black—Oil Absorption Number (OAN) |
ASTM D 5763 : 2022 | Standard Test Method for Oxidation and Thermal Stability Characteristics of Gear Oils Using Universal Glassware |
ASTM D 7863 : 2022 | Standard Guide for Evaluation of Convective Heat Transfer Coefficient of Liquids |
ASTM D 4378 : 2022 | Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines |
ASTM D 1655 : 2022 | Standard Specification for Aviation Turbine Fuels |
ASTM D 7566 : 2022 | Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons |
ASTM D 7665 : 2022 | Standard Guide for Evaluation of Biodegradable Heat Transfer Fluids |
ASTM D 8240 : 2022 | Standard Specification for Less-Flammable Synthetic Ester Liquids Used in Electrical Apparatus |
ASTM D 8350 : 2022 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IVB Spark-Ignition Engine |
ASTM D 8279 : 2022 : REV A | Standard Test Method for Determination of Timing-Chain Wear in a Turbocharged, Direct-Injection, Spark-Ignition, Four-Cylinder Engine |
ASTM D 3591 : 2022 | Standard Test Method for Determining Logarithmic Viscosity Number of Poly(Vinyl Chloride) (PVC) in Formulated Compounds |
ASTM D 8114 : 2022 : REV A | Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIE Spark Ignition |
ASTM D 7414 : 2022 | Standard Test Method for Condition Monitoring of Oxidation in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 7624 : 2022 | Standard Test Method for Condition Monitoring of Nitration in In-Service Petroleum and Hydrocarbon-Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 7412 : 2022 | Standard Test Method for Condition Monitoring of Phosphate Antiwear Additives in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 7415 : 2022 | Standard Test Method for Condition Monitoring of Sulfate By-Products in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 7844 : 2022 : REV A | Standard Test Method for Condition Monitoring of Soot in In-Service Lubricants by Trend Analysis using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 975 : 2022 | Standard Specification for Diesel Fuel |
ASTM D 2226 : 1993 : R2022 | Standard Classification for Various Types of Petroleum Oils for Rubber Compounding Use |
ASTM D 4174 : 2017 | Standard Practice for Cleaning, Flushing, and Purification of Petroleum Fluid Hydraulic Systems |
ASTM D 4243 : 2016 | Standard Test Method for Measurement of Average Viscometric Degree of Polymerization of New and Aged Electrical Papers and Boards |
ASTM D 4304 : 2017 | Standard Specification for Mineral and Synthetic Lubricating Oil Used in Steam or Gas Turbines |
ASTM D 4636 : 2017 | Standard Test Method for Corrosiveness and Oxidation Stability of Hydraulic Oils, Aircraft Turbine Engine Lubricants, and Other Highly Refined Oils |
ASTM D 4878 : 2015 | Standard Test Methods for Polyurethane Raw Materials: Determination of Viscosity of Polyols |
ASTM D 5222 : 2016 | Standard Specification for High Fire-Point Mineral Electrical Insulating Oils |
ASTM D 5363 : 2016 | Standard Specification for Anaerobic Single-Component Adhesives (AN) |
ASTM D 6074 : 2015 | Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils |
ASTM D 6448 : 2016 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
ASTM D 6618 : 2016 | Standard Test Method for Evaluation of Engine Oils in Diesel Four-Stroke Cycle Supercharged 1M-PC Single Cylinder Oil Test Engine |
ASTM D 6681 : 2017 | Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1P Test Procedure |
ASTM D 6871 : 2017 | Standard Specification for Natural (Vegetable Oil) Ester Fluids Used in Electrical Apparatus |
ASTM D 7583 : 2016 | Standard Test Method for John Deere Coolant Cavitation Test |
ASTM D 7596 : 2014 | Standard Test Method for Automatic Particle Counting and Particle Shape Classification of Oils Using a Direct Imaging Integrated Tester |
ASTM D 7417 : 2017 | Standard Test Method for Analysis of In-Service Lubricants Using Particular Four-Part Integrated Tester (Atomic Emission Spectroscopy, Infrared Spectroscopy, Viscosity, and Laser Particle Counter) |
ASTM D 7752 : 2018 | Standard Practice for Evaluating Compatibility of Mixtures of Hydraulic Fluids |
ASTM D 8092 : 2017 | Standard Test Method for Field Determination of Kinematic Viscosity Using a Microchannel Viscometer |
ASTM D 8147 : 2017 | Standard Specification for Special-Purpose Test Fuels for Aviation Compression-Ignition Engines |
ASTM D 8185 : 2018 | Standard Guide for In-Service Lubricant Viscosity Measurement |
ASTM D 6071 : 2014 | Standard Test Method for Low Level Sodium in High Purity Water by Graphite Furnace Atomic Absorption Spectroscopy |
ASTM D 6299 : 2022 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
ASTM E 2593 : 2017 | Standard Guide for Accuracy Verification of Industrial Platinum Resistance Thermometers |
ASTM E 2593 : 2017 : R2023 | Standard Guide for Accuracy Verification of Industrial Platinum Resistance Thermometers |
ASTM D 6300 : 2021 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 6300 : 2023 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 6299 : 2023 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 6299 : 2023 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 6299 : 2022 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
ASTM E 1 : 2014 : R2020 | Standard Specification for ASTM Liquid-in-Glass Thermometers |
ASTM D 6071 : 2014 : R2022 | Standard Test Method for Low Level Sodium in High Purity Water by Graphite Furnace Atomic Absorption Spectroscopy |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.